Poulan PR4016 Support and Manuals
Get Help and Manuals for this Poulan item
View All Support Options Below
Free Poulan PR4016 manuals!
Problems with Poulan PR4016?
Ask a Question
Free Poulan PR4016 manuals!
Problems with Poulan PR4016?
Ask a Question
Most Recent Poulan PR4016 Questions
Poulan Pr4016 Carburetor Replacement
I'm having trouble removing the old carburetor
I'm having trouble removing the old carburetor
(Posted by Mrod02024 1 year ago)
Poulan PR4016 Videos
Poulan Pro PR4016, 16 in. 40cc 2-Cycle Gas Chainsaw Reviews
Duration: :33
Total Views: 104
Duration: :33
Total Views: 104
Poulan Pro PR4016 Upgrade.
Duration: 11:20
Total Views: 305
Duration: 11:20
Total Views: 305
Poulan PR4016 40-cc 2-cycle 16-in Gas Chainsaw
Duration: :43
Total Views: 1,259
Duration: :43
Total Views: 1,259
Popular Poulan PR4016 Manual Pages
Owner Manual - Page 2
...) bulb.
Never operate a chainsaw holding it with any nonroad engine repair
WARNING!
Fuel fill. Please read the operator's manual carefully and make sure you understand the instructions before using the stop switch.
The Emissions Compliance Period referred to oil ratio. Maintenance, replacement, or repair of operating hours for certain markets. The engine is stopped by...
Owner Manual - Page 3
.... IDENTIFICATION (WHAT IS WHAT?)
(*)
(**)
NOTE: The appearance of travel 27. Combination tool 2. Chain 3. Starter rope 7. Depth gauge 25. Chain direction of your product may vary from the item shown.
(*) = Configuration for models equipped with chain tensioning screw located on side. Guide bar retaining nuts 28. Primer (air purge) bulb 11. Rear handle 18. Does not apply...
Owner Manual - Page 4
... have any object while starting when setting up, transporting, adjusting or making repairs except carburetor adjustments. An anti-vibration system does not guarantee the avoidance of your saw when the guide bar is completed.
• Stop the engine before operating a chainsaw.
• Carefully plan your authorized service dealer or call consumer support.
• Do not handle or...
Owner Manual - Page 5
..., screws, and fasteners securely tightened.
• Use only genuine accessories and replacement parts as recommended.
• Your saw cool in a reversal of the guide bar. A loose or dull chain can cause the chain to dig into the object, which kicks the guide bar up all chainsaw service performed by law that could easily cause the operator to lose control...
Owner Manual - Page 6
... your saw. KICKBACK SAFETY FEATURES
WARNING!
REDUCED KICKBACK GUIDE BAR
The reduced-kickback guide bar is required and shall not be removed or otherwise disabled to the place of the saw with the cutting chain.
• Do not overreach.
• Use wedges made by an authorized servicing dealer. It is designed to help reduce the hazard...
Owner Manual - Page 8
... use of the machine:
• Check fuel mixture level • Check bar lubrication • Check chain sharpness
NOTE: Chain sharpening is a complicated task that you refer chain sharpening to a professional chain sharpener.
• Check chain tension • Inspect and clean the guide bar • Check for damaged parts • Check for loose caps • Check for loose fasteners •...
Owner Manual - Page 9
... until the machine attempts to start before you start , refer to the TROUBLESHOOTING TABLE or call the consumer assistance help line. Flooded engines can be completely filled. WARNING! Pull the blue choke lever to CARBURETOR ADJUSTMENT within this manual. If the chain moves at idle speed refer to the FULL CHOKE position. Starting a Warm...
Owner Manual - Page 13
... as you and the chain. A worn guide bar will need to be made periodically to one side or at the base of the limb. 2. Remove these burrs with one -third of the way through the cut all sawdust from saw in the repair parts list or on the decal located on this manual. Remove small limbs with...
Owner Manual - Page 14
...CHAIN BRAKE in Canada, the spark ignition system complies with a 3/4 inch (19 mm) socket wrench to 15-25 ft-lb. Remove the exhaust outlet cover. 3. Reinstall spark arresting screen, exhaust outlet
cover, and nut. SPARK PLUG NOTE: For models... or damaged parts. Remove the spark arresting screen (C). Replace and reassemble. Wipe off the spark plug boot (C). 4.
Install a new ...
Owner Manual - Page 15
... etc. Adjustments may be moving chain can cause serious cuts to yourself or others that a complete service is carried out before long-term storage.
• The guide bar and chain should be covered with all guards... sparks or open flames from the unit. The chain will not idle. Indications for idle speed adjustment
The carburetor has been carefully set at idle speed. Turn the idle speed screw ...
Owner Manual - Page 16
... switch off. 2. Spark plug not firing. 5. repair or
replace.
Chain brake locked.
4.
REMEDY
• See "CARBURETOR ADJUSTMENT" in the STARTING AND STOPPING section.
• Contact an authorized service dealer.
replace. • Check for dirty fuel filter; TROUBLE: Engine will not idle properly. TROUBLE: Chain moves at idle speed. Idle speed r e q u i r e s adjustment...
Owner Manual - Page 17
....1 when used on your saw . The following guide bar and chain combinations meet the CKA requirements per standard. Model
Guide Bar
P/N
Length (in/cm)
Chain
CKA without activation of saw and listed in the CKA table below represents angle of kickback your bar and chain combinations will have when tested in this manual.
In all cases lower CKA values represent a safer...
Owner Manual - Page 18
..., REPLACEMENT AND REPAIR OF EMISSION RELATED PARTS: Any Husqvarna Consumer Outdoor Products N.A., Inc. YOUR WARRANTY RIGHTS AND OBLIGATIONS: The U.S. Husqvarna Consumer Outdoor Products N.A., Inc. must be warranted for the performance of the required maintenance listed in a reasonable amount of your instruction manual. Your emission control system includes parts such as a problem exists...
Parts List - Page 7
... 03 78-20 PISTON
16
530 05 79-24 ASSEMBLY
PR4016, 967084601, 2016-05
Remark
QTY KIT
CLUTCH WASHER KIT (INCL. 3)
1
CLUTCH DRUM ASSEMBLY
1
CLUTCH WASHER KIT (INCL. 1)
1
SCREW
4
CHAIN BRAKE KIT
1
CLUTCH ASSY
1
LARGE CLUTCH WASHER
1
BAR MOUNTING PLATE 1
HANDGUARD
1
"CHAIN 91PJ 16"" 3/8"" 56DL (POULAN/POULAN 1 PRO)"
"BAR, POULAN PRO 16 IN"
1
OIL PUMP KIT
1
SCREW
2
OIL PUMP...
Parts List - Page 9
CLUTCH COVER
Ref
Part No
Description
1
585 36 91-03 COVER
2
530 01 59-17 NUT
-
582 02 31-02 SERVICE KIT
PR4016, 967084601, 2016-05
Remark
CLUTCH COVER ASSY (INCL. 3)
BAR NUT
SIDE ADJUST SCREW AND GEARS KIT
QTY KIT 1 2 1
Poulan PR4016 Reviews
We have not received any reviews for Poulan yet.