User Manual
Page 8
...pressure to -rear for leveling). ✓ Check mower and drive belts. Be sure they are properly inflated. (For shipping purposes, the tires were overinflated at the factory). ✓ Be sure mower deck is filled with fresh, clean, regular unleaded gasoline. ...10003; Become familiar with washer and 5/16 retainer spring (J). 5/16 E H J F G 7/16 FIG. 11 • Disengage belt tension rod (K) from left side of this manual. PLEASE ...
...pressure to -rear for leveling). ✓ Check mower and drive belts. Be sure they are properly inflated. (For shipping purposes, the tires were overinflated at the factory). ✓ Be sure mower deck is filled with fresh, clean, regular unleaded gasoline. ...10003; Become familiar with washer and 5/16 retainer spring (J). 5/16 E H J F G 7/16 FIG. 11 • Disengage belt tension rod (K) from left side of this manual. PLEASE ...
User Manual
Page 22
... may have accumulated around mandrels and entire upper deck surface. • Remove belt from stationary idler (C) and clutching idler (D). • Raise attachment lift lever to front, over cooling fan blades (F). • Remove belt downward from lock bracket (L). Pull freewheel control ...• Reinstall anti-rotation link (B) on centerspan idler (E). Tighten securely. • Reconnect clutch harness (A). • Make sure belt is a belt installation guide decal on a level surface. ing plate (H) and above clutch brake pedal shaft (J). For assistance, there is in highest...
... may have accumulated around mandrels and entire upper deck surface. • Remove belt from stationary idler (C) and clutching idler (D). • Raise attachment lift lever to front, over cooling fan blades (F). • Remove belt downward from lock bracket (L). Pull freewheel control ...• Reinstall anti-rotation link (B) on centerspan idler (E). Tighten securely. • Reconnect clutch harness (A). • Make sure belt is a belt installation guide decal on a level surface. ing plate (H) and above clutch brake pedal shaft (J). For assistance, there is in highest...
User Manual
Page 27
...1. Replace blade mandrel. 5. Low/uneven tire air pressure. 5. Mower drive belt worn. 8. Replace regulator. 4. Air trapped in "engaged" position. 2. See Operation section. Clogged mower deck vent holes from buildup of mower housing. 4. Frozen idler pulley. 4. Reverse...Clean around mandrels. 1. Headlight(s) not working (if so equipped) 1. Purge transmission. Replace idler pulley. 4. Mower deck not level. 4. Replace mower drive belt. 9. Engine continues to open vent holes. Check wiring, switches and connections. Check tires for proper air pressure....
...1. Replace blade mandrel. 5. Low/uneven tire air pressure. 5. Mower drive belt worn. 8. Replace regulator. 4. Air trapped in "engaged" position. 2. See Operation section. Clogged mower deck vent holes from buildup of mower housing. 4. Frozen idler pulley. 4. Reverse...Clean around mandrels. 1. Headlight(s) not working (if so equipped) 1. Purge transmission. Replace idler pulley. 4. Mower deck not level. 4. Replace mower drive belt. 9. Engine continues to open vent holes. Check wiring, switches and connections. Check tires for proper air pressure....
Parts List
Page 15
... Arm, Idler Screw, Thdroll. 1/4-20 x 5/8 V-Belt, Mower Nut, Lock Flg. 3/8-16 unc Bolt RDHD SQNK 3/8-16 unc x 2 Pulley Idler Clutching KEY PART NO. inches 1 inch = 25.4 mm 15 PB22H54YT (96042002900), PRODUCT NO. 960 42 00-29 MOWER DECK KEY PART NO. Service (Includes Key Nos. 13-15... Nut, Push Deflector Shield Rod, Hinge Screw, Thdroll Washer Head Washer, Spacer Mower Vented Pulley, Mandrel Nut, Flg. Mower Rear Bolt Shoulder Keeper Belt Idler Bolt Carr Sqnk 3/8-16 x 2-1/4 Bolt Rdhd Sqnk 3/8-16 x 2-1/2 Gr. 5 Bolt Rdhd Swnk 5/16-18 x 5/8 Mandrel Asm. MODEL NO. NO. 1 195632X421 6 ...
... Arm, Idler Screw, Thdroll. 1/4-20 x 5/8 V-Belt, Mower Nut, Lock Flg. 3/8-16 unc Bolt RDHD SQNK 3/8-16 unc x 2 Pulley Idler Clutching KEY PART NO. inches 1 inch = 25.4 mm 15 PB22H54YT (96042002900), PRODUCT NO. 960 42 00-29 MOWER DECK KEY PART NO. Service (Includes Key Nos. 13-15... Nut, Push Deflector Shield Rod, Hinge Screw, Thdroll Washer Head Washer, Spacer Mower Vented Pulley, Mandrel Nut, Flg. Mower Rear Bolt Shoulder Keeper Belt Idler Bolt Carr Sqnk 3/8-16 x 2-1/4 Bolt Rdhd Sqnk 3/8-16 x 2-1/2 Gr. 5 Bolt Rdhd Swnk 5/16-18 x 5/8 Mandrel Asm. MODEL NO. NO. 1 195632X421 6 ...