User Manual
Page 1
ALWAYS WEAR EYE PROTECTION DURING OPERATION Visit our website: www.poulan-pro.com 417217 Rev. 2 09.19.08 SBW Printed in serious injury. Failure to do so can result in the U.S.A. IMPORTANT MANUAL DO NOT THROW AWAY 03076 OPERATOR'S MANUAL MODEL: PB195H46YT LAWN TRACTOR WARNING: Read this Manual and follow all Warnings and Safety Instructions.
ALWAYS WEAR EYE PROTECTION DURING OPERATION Visit our website: www.poulan-pro.com 417217 Rev. 2 09.19.08 SBW Printed in serious injury. Failure to do so can result in the U.S.A. IMPORTANT MANUAL DO NOT THROW AWAY 03076 OPERATOR'S MANUAL MODEL: PB195H46YT LAWN TRACTOR WARNING: Read this Manual and follow all Warnings and Safety Instructions.
User Manual
Page 10
...height range is approximately 1" to desired height. Make the first cut to approximately 2-1/2 inches during the cool season and to leave the seat with tractor on mowers so equipped, or the deflector shield (S) in place. NOTE: Adjust gauge wheels with the engine running . You must remain fully ... gauge wheel in desired cutting height slot. TO ADJUST MOWER CUTTING HEIGHT (See Fig. 8) The position of grass being mowed. • The average lawn should be cut relatively high; A FIG. 8 • Put attachment lift lever in same adjustment hole. Any attempt by the operator to travel in...
...height range is approximately 1" to desired height. Make the first cut to approximately 2-1/2 inches during the cool season and to leave the seat with tractor on mowers so equipped, or the deflector shield (S) in place. NOTE: Adjust gauge wheels with the engine running . You must remain fully ... gauge wheel in desired cutting height slot. TO ADJUST MOWER CUTTING HEIGHT (See Fig. 8) The position of grass being mowed. • The average lawn should be cut relatively high; A FIG. 8 • Put attachment lift lever in same adjustment hole. Any attempt by the operator to travel in...
User Manual
Page 17
... CLAMP CLAMP FUEL FILTER FIG. 16 CLEANING • Clean engine, battery, seat, finish, etc. While sitting in the operator's position on the tractor, re-start the engine and place the throttle lever in engine or transmission will shorten the useful life of your house, garage, parked cars, etc...sec- of all foreign matter. • Keep finished surfaces and wheels free of this manual. Turn the water on your lawn, near enough to a water spigot for your tractor unless the engine and transmission are shown in one year. IMPORTANT: Recheck the area making certain the area is used more...
... CLAMP CLAMP FUEL FILTER FIG. 16 CLEANING • Clean engine, battery, seat, finish, etc. While sitting in the operator's position on the tractor, re-start the engine and place the throttle lever in engine or transmission will shorten the useful life of your house, garage, parked cars, etc...sec- of all foreign matter. • Keep finished surfaces and wheels free of this manual. Turn the water on your lawn, near enough to a water spigot for your tractor unless the engine and transmission are shown in one year. IMPORTANT: Recheck the area making certain the area is used more...
User Manual
Page 20
... should be level side-to 1/2" lower than the rear tip when the mower is 1/8" to 1/2" lower than the rear tip, go to the front of tractor. • With an 11/16" or adjustable wrench, loosen jam nut A several turns to clear adjustment nut B. • With a 3/4" or adjustable wrench, ...tighten jam nut securely against adjustment nut. 20 PRECISION SIDE-TO-SIDE ADJUSTMENT (See Fig. 24) • With all tires properly inflated and if your lawn appears unevenly cut, determine which side of mower is cutting lower. • With a 3/4" or adjustable wrench, turn lift link adjustment nut (A) to ...
... should be level side-to 1/2" lower than the rear tip when the mower is 1/8" to 1/2" lower than the rear tip, go to the front of tractor. • With an 11/16" or adjustable wrench, loosen jam nut A several turns to clear adjustment nut B. • With a 3/4" or adjustable wrench, ...tighten jam nut securely against adjustment nut. 20 PRECISION SIDE-TO-SIDE ADJUSTMENT (See Fig. 24) • With all tires properly inflated and if your lawn appears unevenly cut, determine which side of mower is cutting lower. • With a 3/4" or adjustable wrench, turn lift link adjustment nut (A) to ...