Poulan P4018WTL Support and Manuals
Get Help and Manuals for this Poulan item
View All Support Options Below
Free Poulan P4018WTL manuals!
Problems with Poulan P4018WTL?
Ask a Question
Free Poulan P4018WTL manuals!
Problems with Poulan P4018WTL?
Ask a Question
Popular Poulan P4018WTL Manual Pages
User Manual - Page 3
... the cut . Always
replace bar, chain, hand guard, or chain brake immediately if it becomes damaged, broken or is strenuous. S With the engine stopped, hand carry the chain saw at the end of the guide bar. For correction, refer to dig into the object, which kicks the guide bar up all parts of this manual. Slowly remove fuel cap and refuel unit. Applying...
User Manual - Page 4
...guide bar and the saw chain sharp and properly tensioned. S Pinch-Kickback can occur when the the wood closes in and pinches the moving saw chain in a direct line with the cutting chain.... Follow manufacturer's chain sharpening and maintenance instructions.
It is running . drawn from obstructions such as the bar is suddenly stopped. S Watch for your saw chain is driven straight back...
User Manual - Page 5
... is not recommended and
may push the guide bar rapidly back toward the operator. YOU SHOULD USE THE SAW PROPERLY AND CAREFULLY TO AVOID KICKBACK. Repairs
on a chain brake should be made by an authorized servicing dealer. S Tip contact in -line" with safety requirements for the user. When purchasing replacement bar and chain, considerations should be given to significantly reduce...
User Manual - Page 6
.... 2. Failure to do so is a violation of shipping spacer
3. STANDARDS: This saw is listed by law that many internal combustion engines to be equipped with a spark arresting screen. Computed kickback angle (CKA) Table
BAR
MODEL
P/N
Length CHAIN P/N
CKA without chain brake
P4018WTL
530044749 18″
952051338
33_
NOTE: If this saw is to be used for...
User Manual - Page 7
... the adjusting screw. Guide Bar
Bar bolts
Guide bar
5. Hold chain with chain already installed)
WARNING: Wear protective gloves
when handling chain. An adjusting screw (located on bar bolts until guide
bar stops against the saw . Adjusting Screw
Drive Links
6. The chain is not moving.
3. Lift up tip of guide bar, tighten bar nuts securely with the bar tool. Bar Nuts
6. 7.
7
Use the...
User Manual - Page 8
...during cold starting .
OPERATION
KNOW YOUR CHAIN SAW READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR
CHAIN SAW.
Chain Adjustment Tool
(Bar Tool)
Front Hand Guard
Front Handle Starter Rope
Chain
Muffler
ON/STOP Switch Choke/
Fast Idle
Lever
Bar Sprocket
Hole
Bar Oil Fill Cap Starter Housing
Primer Bulb Fuel Mix Fill Cap
Cylinder Cover
Throttle Lockout Rear Handle...
User Manual - Page 9
..., vapor
lock, power loss, lubrication deficiency, deterioration of fuel lines, gaskets and internal carburetor components, etc. Poulan oil resists high temperature thinning. If Poulan bar and chain oil is not available, use of minimum 87 octane [R+M]/2 clean gasoline. Avoid contact with this manual before you do not understand the fuel handling information do so.
Hold saw is a 3.2 ounce...
User Manual - Page 10
... band is worn
too thin it is flooded. Repairs on how badly the unit is disengaged by pulling the front hand guard back toward the front handle as far as possible. S This saw , the chain brake must be replaced by an authorized service dealer if any part is in the ON position.
S When cutting with...
User Manual - Page 14
... the warranty, the operator must maintain unit as instructed in the instruction manual performed by an authorized service dealer.
Before each use For loose caps Before each use, ensure ON/STOP switch is in this manual. Yearly Replace fuel filter . . . To receive full value from the guide bar and sprocket hole. S Oil Tank -- A dull chain makes a sawdust powder and cuts slowly. See...
User Manual - Page 17
..., contact your authorized service dealer or call our customer assistance help line at idle.
Adjust speed until engine runs without chain movement (idle too fast) or stalling (idle too slow). If you require further assistance or are using. Fuel stabilizer is higher than the
depth gauge tool, file it in the fuel tank or fuel storage container...
User Manual - Page 18
... an authorized service dealer.
1. Replace any damaged, broken, or worn parts. Spark plug not firing. 5. Engine will run only a few seconds after adding stabilizer. Air filter dirty. 2. Clutch requires repair.
1. Contact an authorized service dealer.
1. Run engine at idle speed.
1. Poulan/WEED EATER 40:1, 2-cycle engine oil (air cooled) is blended with gasoline.
1.
Chain brake engaged...
User Manual - Page 19
... Poulan reserves the right to change, modify, or discontinue models, designs, specifications, and accessories of guide bar and chain, and normal adjustments explained in the instruction manual such as listed under Emissions Control Warranty Parts List) is defective or a defect in the materials or workmanship of the engine causes the failure of such an emission related part, the part will repair...
User Manual - Page 20
... be completed in the instruction manual.
RIOD: Any warranted part which is longer). ranted part is defective if the diagnostic work is responsible for
2 years. ing center. HOW TO FILE A CLAIM: If you have any warranty maintenance or repair on or modified parts. RANTY SERVICE: Warranty services or repairs shall be warranted for the performance of "repair or replace as defined in...
Parts List - Page 1
...Description
Ref. PARTS LIST NO.
545103413
DATE
4/16/09
Replaces 545103413 --- 7/03/08
3 2 1
5
WPAEREPDAOMUEOLAATUNENRRTRRrRPAPPRAATRRSTTSLSILSLITSISTT
CHAIN SAW MODEL(s)
P4018WTL
Note: Illustration may differ from actual model due to design changes
4
6
7
8
WARNING
All repairs, adjustments and maintenance
not described in the Operator's Manual
must be performed by qualified service...
Parts List - Page 2
... Module --
Part No. Seal--Adaptor (kit) Screw Gasket--Carb. (kit) Tube--Intake Wire--Throttle Nut--Carb. Description
Ref. Ignition Screw Strap--Ground Assy--Wire Harness Cover--Air Filter Filter--Air Screw Housing--Air Filter Carburetor (Incl. 14)
Walbro WTA30 Zama W--26B Kit--Fuel Line (Small) Bulb--Purge "snap--in the Operator's Manual must be performed by qualified service personnel...
Poulan P4018WTL Reviews
We have not received any reviews for Poulan yet.