Pioneer PRS-D2000SPL - Premier Amplifier Support and Manuals
Get Help and Manuals for this Pioneer item
View All Support Options Below
Free Pioneer PRS-D2000SPL manuals!
Problems with Pioneer PRS-D2000SPL?
Ask a Question
Free Pioneer PRS-D2000SPL manuals!
Problems with Pioneer PRS-D2000SPL?
Ask a Question
Most Recent Pioneer PRS-D2000SPL Questions
Pioneer PRS-D2000SPL Videos
?udi A6 Ground Zero GZRW38 SPL + Pioneer PRS-D2000SPL 2
Duration: 2:02
Total Views: 824
Duration: 2:02
Total Views: 824
Unboxing Pioneer PRS-D2000SPL amplifier and comparing it to PRS-D1200SPL
Duration: 3:06
Total Views: 3,210
Duration: 3:06
Total Views: 3,210
Audi ?6 Ground Zero GZRW38 SPL + Pioneer PRS-D2000SPL 3
Duration: 2:03
Total Views: 573
Duration: 2:03
Total Views: 573
Audi A6 Ground Zero GZRW38 SPL + Pioneer PRS-D2000SPL 1
Duration: 2:24
Total Views: 2,557
Duration: 2:24
Total Views: 2,557
Popular Pioneer PRS-D2000SPL Manual Pages
Owner's Manual - Page 2
... its after-sales service (including warranty conditions) or any questions, contact your own security and convenience, write it down on the enclosed warranty card. PIONEER SUGGESTS USING A PROFESSIONAL INSTALLER DUE TO THE COMPLEXITY OF THIS PRODUCT. Please read all instructions and WARNINGS in this amplifier is not available, please contact the companies listed below for repair without...
Owner's Manual - Page 3
...an electric shock. Also, do not touch the amplifier when it is a mono amplifier. Detect the cause and solve the problem, then replace the fuse with liquids due to maintain safe ...the amplifier. In such a case, switch the power to protect all cables and important equipment such as loss or theft.
2 Receive updates on the latest products and technologies.
3 Download owner's manuals, order...
Owner's Manual - Page 4
... instruction of these amplifiers in which they are connected.
See the "Connecting the Speaker Wires" section for LPF
You can select a cut off frequency from MASTER, SYNC and SYNC INV. Bass Boost Frequency Control
You can select a bass boost frequency from 0, 6, 9 and 12 dB. When switching to the manner in combination, set the first amplifier...
Owner's Manual - Page 5
... output level. • For synced amplifier's gain control, see the "Setting the Gain for synced amplifier" section. output of 500 mV), set to the NORMAL
position. PROTECT Indicator (Red)
This indicates a problem with max. When using with an RCA equipped Pioneer car stereo with the amplifier. See the "Troubleshooting" section on . BFC (Beat Frequency Control) Switch
If you hear a beat...
Owner's Manual - Page 6
...., this is increased and the power increases only slightly. Setting the Unit
Setting the Gain properly
• This unit is controlled. Gain Control of This Unit
There is no need to decrease the ...output will cut , the gain control of the amplifier to time, contact the nearest authorized PIONEER Service Station.
5
Relationship between the gain of the amplifier and the output power of the ...
Owner's Manual - Page 7
...
• If the system remote control wire of whether the car stereo... to the supplied manuals of both products and...replace the fuse with a 12-volt battery and negative grounding. Amplifier damage, smoke, and overheating could cause damage to the touch and minor burns could go dead. The amplifier surface could also become damaged.
• Install...they lie against metal parts.
• Do...
Owner's Manual - Page 8
... Wires" section for SYNC OUTPUT/SYNC INPUT jack connection instructions. If the car stereo does not have a system remote control terminal, connect the male terminal to the RCA input.
Each amplifier must be connected to the system remote control terminal of the car stereo (SYSTEM REMOTE CONTROL). SYNC OUTPUT/SYNC INPUT jack See the "Connecting...
Owner's Manual - Page 9
...with the terminal screws.
However, since excessively tightening the terminal screw of the System remote control has the risk of damaging the wire, be periodically inspected and tightened as necessary.
.... • Use the supplied hexagonal wrench to tighten and
loosen the terminal screw of the amplifier. less than 21 ft. Put the wire ties in .)
2. Connecting the Speaker Output Terminals...
Owner's Manual - Page 10
... screw Terminal
screw
GND terminal
System remote control wire
Ground wire
WARNING
Failure to securely fasten the battery wire to the terminal using nippers or a cutter.
• Battery wire, ground wire: 23 mm to the positive (+) terminal of
compartment the vehicle
Fuse 300 A Positive (+) Each amplifier must be SEPARATELY
fused at 300...
Owner's Manual - Page 11
...
Setting the Gain for synced amplifier
After connecting the speaker wires, adjust each synced amplifier in the proper order. Match the synced amplifier's output to the master's output using the gain control on each synced amplifier's gain control to MASTER with the master amplifier, adjust the gain control on the synced amplifier. 5. Advanced Setup of the Gain
Set each amplifier...
Owner's Manual - Page 12
... MASTER position. Connect to the speaker instruction manual for information on the correct connection procedure. The amplifier surface could result. Proper
Amplifier
Diagram B - Improper
Amplifier
4 Ω Speaker
4 Ω Speaker
2 Ω Speaker
2 Ω Speaker
2 Ω Bridged Mode
Amplifier
1 Ω Bridged Mode
Amplifier
DO NOT install or use a single 2 Ω speaker...
Owner's Manual - Page 15
... position.
SYNC INPUT
Connecting wire with RCA pin plugs (sold separately). Before setting to the position, remove the screw and the stopper. SYNC INPUT
SYNC OUTPUT...the position, remove the screw and the stopper. Four Amplifier
MODE SELECT switch
must be in SYNC position. SYNC OUTPUT
Connecting wire with RCA pin plugs (sold separately). Before setting to 8 Ω 2 000 W (1 Ω...
Owner's Manual - Page 16
... the supplied parts in the manner specified. Protect all cables and important equipment such as under the dashboard. Installation
CAUTION
• Do not install in: -Places where it could injure the driver or passengers if the vehicle stops suddenly. -Places where it may become loose causing the amplifier to shut down.
• Never replace the fuse...
Owner's Manual - Page 18
..." section on page 2). PROTECT Indicator
• This indicator either flashes or lights up in the amplifier. When this happens, immediately discontinue use of the amplifier and check the location where the amplifier is not a malfunction. This is installed (see the "WARNING" section on . Additional information
Troubleshooting
The following indicators light momentarily when the...
Owner's Manual - Page 19
... multiple power amplifiers.
18 Subsonic filter (HPF) ...Frequency: 20 Hz
Slope: -24 dB/oct. Bass boost ...Frequency: 40 Hz to 120 Hz
Level: 0 / 6 / 9 / 12 dB Gain control ...RCA: ...8226; The average current drawn is input. ENGLISH
ESPAÑOL DEUTSCH FRANÇAIS ITALIANO NEDERLANDS
Specifications
Power source ...14.4 V DC (10.8 V to 15.1 V allowable) Grounding system ...Negative type...
Pioneer PRS-D2000SPL Reviews
We have not received any reviews for Pioneer yet.