Panasonic AJSD955A - DVC PRO CAMCORDER Support and Manuals
Get Help and Manuals for this Panasonic item
View All Support Options Below
Free Panasonic AJSD955A manuals!
Problems with Panasonic AJSD955A?
Ask a Question
Free Panasonic AJSD955A manuals!
Problems with Panasonic AJSD955A?
Ask a Question
Popular Panasonic AJSD955A Manual Pages
AJSD930 User Guide - Page 2
..., REFER CHANGE OF SWITCH SETTING INSIDE THE UNIT TO QUALIFIED SERVICE PERSONNEL. This equipment generates, uses, and can be extremely hazardous.
CAUTION:
TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, REFER MOUNTING OF THE OPTIONAL INTERFACE BOARD TO QUALIFIED SERVICE PERSONNEL. FCC Note: This device complies with the instruction manual, may cause harmful interference...
AJSD930 User Guide - Page 3
Contents
Introduction 3
Features 4
Parts and their functions 5 Front panel 5 Display panel 11 Rear panel 13
Connections 15
Tapes 17
Jog/Shuttle 18
Manual editing SD955A 19
Preroll SD955A 19
Automatic editing (deck-to-deck) SD955A 20 Switch settings and adjustments 20 Selecting the editing mode 21 Registering the edit points 21 Checking and previewing...
AJSD930 User Guide - Page 4
...as the time code.
4
O 9-pin RS-422A/RS-232C remote In addition to operating the unit, are provided. Switching between 525i and 625i TV systems SD955A
By selecting the setting (setup menu item No... 1/4-inch.
Compatibility with DVCPRO (25 Mbps) format
This unit can be used with a consumer digital camera or the like can record, play back and edit material in addition to 92 minutes of the...
AJSD930 User Guide - Page 5
... SDTI/1394 cannot be recorded on setup menu No. 600 (INT SG). Parts and their functions
Front panel
1...digital signals CH4 : Analog input signals
O It is used in the unit are displayed here. O USER SET is a function which enables the input signals to be selected unless one of DVCPRO50 (50 Mbps) format tapes. EJECT button operation can be selected and recorded separately on setup...
AJSD930 User Guide - Page 8
... button This button is pressed to proceed with assemble editing. Parts and their functions
Front panel
L
JKIHE F
ON
POWER
OFF...when it is used to be entered as the setup menu No. 313 (AUTO ENTRY) setting. button while the IN (A IN) button or...a transmission or manual editing starts on the recorder's monitor. G IN (A IN), SET and OUT (A OUT) buttons SD955A When the SET button is pressed...
AJSD930 User Guide - Page 9
...is pressed, the data which monitor output is to which has been set using setup menu No. 735 (MON AUTO SEL). Parts and their functions
Front panel
M
ON
POWER
OFF
DVCPRO
DVCPRO 50...to be selected using the setup menus is displayed by the lighting of digits whose display is flashing is used to the MONITOR L and R connectors. When the internal time code has been set of the L or ...
AJSD930 User Guide - Page 11
...error rates for the video or audio playback level has increased to switch between the 525 interlace and 625 interlace systems by a flashing display. The playback picture and sound remain unaffected even while this lamp is indicated by setting setup...: Digital audio signals
USER SET : Recording audio signal selection
SDI
: Serial digital audio signals
SDTI/1394 : Compressed digital signals...
AJSD930 User Guide - Page 13
Parts and their functions
Rear panel
1
AC IN
SIGNAL GND
2 3 4 5 6 7 8 9: ; For termination at this socket and the other for digital...CH3
CH4
MON
R
1
2
SERVICE ONLY
1 AC IN socket Connect ...code generated by the internal time code generator is selected using setup menu No. 212 (MASTER PORT).
7 ENCODER REMOTE connector An external encoder remote controller is connected to this VTR, set...
AJSD930 User Guide - Page 14
... (AJ-YAC930G, optional accessory) is installed in this VTR in order to minimize...superimposed information can be input and output using setup menu No. 00 (WFM SEL).
If...set ON or OFF is selected using the SUPER switch W on the component connected to this VTR, digital data can be output through these connectors. Parts...
R
1
2
SERVICE ONLY
> ?@ A
BC D
< Fan This fan ...
AJSD930 User Guide - Page 15
...
L
3 (SUPER)
OPTION
SDTI
IN
OUT
CH3
CH4
MON
R
1
2
SERVICE ONLY
To video monitor device
To audio monitor device
Digital audio
To video monitor device
To audio monitor device
Analog video signal (component) OWhen the analog video input board (option) has
been installed.
Connections
Source machine: Set the CONTROL switch on the front panel to...
AJSD930 User Guide - Page 19
... point has not been registered, it is rewound from the edit IN point for the period of time which was set by setup menu No. 000 (P-ROLL TIME), and it then stops. Manual editing SD955A
1 Select the editing mode. ASSEMBLE: Assemble (frame-to-frame continuity) editing is performed in this mode.
2 Select the...
AJSD930 User Guide - Page 35
..., when the
menu is exited, operation complies with the format recorded on the
vertical plane for the time code and other
CHARA V-POS super displays output to the VIDEO OUT 3/
SDI OUT 3 connector.
011 CHARA ...extend beyond the edges of setup menu No. 012 (SYS FORMAT) when a DVCPRO cassette is to be played back.
0000 MANUAL : The format complies with the setting of the characters on the ...
AJSD930 User Guide - Page 40
...preset when editing the digital audio of setting as setup menu No. 305.
This sets the channel assignments for the analog audio signals designated by the controller.
0000 N-DEF : Not set.
0001 CH1 :... cleared or set again properly.
0001 AUTO : The edit points already input are processed. (Forced
NON-STD)
Use the non-standard (N-STD) setting when
video or audio trouble occurs with ...
AJSD930 User Guide - Page 55
... values to be performed using setup menu No. 503 (TCG REGEN) and No. 504 (REGEN MODE). Time code/user bit
Time code
The time code is used for regeneration even when the TCG switch has been set to PRESET.
5 Use the TC PRESET button to set the start number has been set of digits starts flashing. 2 To change...
AJSD930 User Guide - Page 69
... specifications Connector: D-SUB 25-pin (crossover cable supported)
Pin No. 1 2 3 4 5 6 7 20
Signal
Description
FG RXD TXD CTS RTS DTR SG DSR
Protective ground (Frame ground)
Received data (Data is sent to PC.)
Transmitted data (Data is received from RS-232C interface
O The front panel CONTROL switch must be ON.
Whether the [ACK] code...
Panasonic AJSD955A Reviews
We have not received any reviews for Panasonic yet.