Oki OKIPOS407II Support and Manuals
Get Help and Manuals for this Oki Data item
View All Support Options Below
Free Oki OKIPOS407II manuals!
Problems with Oki OKIPOS407II?
Ask a Question
Free Oki OKIPOS407II manuals!
Problems with Oki OKIPOS407II?
Ask a Question
Popular Oki OKIPOS407II Manual Pages
OKIPOS 407II Warning Buzzer Instruction Sheet - Page 1
...installed and used in accordance with the Federal Noise Interference Standard, this equipment in a residential area is likely to cause harmful interference in the Radio Interference Regulations of the Canadian Department of May 1989. For compliance with the instruction manual, may cause harmful interference to correct the interference at his own expense. Parts... on each model.
EC Council...
OKIPOS New Power Supply Safety Precautions - Page 1
...or other than the "Supported Devices".
Improper repair work can be kept in...then contact your dealer or a service center for advice. •...set this product yourself. If this device, affix it is clean before plugging it in a residential installation... instructions, may cause undesired operation." For compliance with Part 15... in the event of a problem with this document carefully, and...
407II Safety Warranty and Regulatory Information English Fran?ais Espa?ol Portugu?s - Page 2
...read the provided setup and operating instructions.
• ...replaced. If the cord becomes damaged or frayed, replace it immediately.
• If you place it immediately and follow all warning and instruction...Models
Your OKI 407II has been carefully designed to give you to shocks or other hazards.
• Do not make any adjustments other than the
extension's rating. do not try to service...
407II Safety Warranty and Regulatory Information English Fran?ais Espa?ol Portugu?s - Page 4
... the service locations listed...problem over the phone. A written receipt for the Product, showing the date of purchase, dealer's name, and both the model...COMMERCIAL CODE ADOPTED...will repair or at its option, replace, ...with the exchange product. The Product to be returned must accompany any such defect according to abuse, misuse, misapplication, accident, improper storage, or installation...
407II Safety Warranty and Regulatory Information English Fran?ais Espa?ol Portugu?s - Page 5
... for the latest information at any time. This Limited Warranty applies to -the-minute Oki information specifically for your product, including:
• Product news • Manuals • Drivers and utilities
5 - Contact your machine handy. Oki Data Authorized Service Providers For the most comprehensive, up -to this Product. Laurel, NJ 08054
Phone: 1-800-654-3282...
OKIPOS 407 / 407II Users Guide - Page 2
...instruction manual, may cause harmful interference to radio communications.
Notice • All rights reserved. Federal Communications Commission Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for radio noise emissions from digital apparatus set...installed and used in Canada. However, should any errors...acknowledgments OKIPOS407II: ...
OKIPOS 407 / 407II Users Guide - Page 3
...
3. Setup...4 3-1. Attaching the Accessories...17 4-1. Consumable Parts and AC Adapter...20 5-1. Errors...28 6-3. Preventing and Clearing Paper Jams 33 8-1. Reliability Specifications...38 10-7. Thermal Label Paper Roll (Tack Label Paper 23 5-4. Control Panel and Other Functions...28 6-1. Adjusting the Near-end Sensor...31
8. Unpacking and Installation...1 1-1. Choosing...
OKIPOS 407 / 407II Users Guide - Page 18
...a 57.5 mm width, remove the paper roll holder, and install the paper roll holder into the other groove. Position ①...
- 14 -
In either case, change to the separate Specifications Manual. For instructions on the adjustment lever engages with the hole in accordance with... on setting the memory switch, refer to a paper roll with the paper thickness.
3-7-2. This is factory-set to ...
OKIPOS 407 / 407II Users Guide - Page 36
...7.1
1.7
4.0
6.4
1.4
3.2
5.2
1.2
2.8
4.5
C
Note:
1) The adjuster is used to the separate Specifications
Manual.
3) The detected diameter and remained paper length
A
given above are using
Paper thick-ness When using the paper ...Approx. For instructions on the rolled state of the
Paper roll core
C
paper or the actual mechanism. 4) If thick paper is factory-set the
adjustor ...
OKIPOS 407 / 407II Users Guide - Page 44
... item like a pen or flat-blade driver screw to change the settings. Be sure to set to off the DIP switch blind, as...set as shown
in the table below .
3. Set the switches using a pointed tool, such as a pen or flat-blade screwdriver. 4. The new settings take off before changing the settings.
Make sure the printer is set the power switch to on the printer.
- 40 - Replace...
OKIPOS 407 / 407II Users Guide - Page 45
11-1. Parallel Interface Model
ON
ON
OFF No. 1 2 3 4 5 6 7 8 9 10
DIP-SW 1
OFF No. 1 2 3 4
DIP-SW 2
Switch 1-1 ON OFF
DIP-SW 1
The factory settings of switches 1-2 through 1-10 will change according to the command emulation that has been set using switch 1-1.
(1) Star mode
Switch
Function
1-1
Command emulation
1-2
Should not be changed (Should be set to on...
OKIPOS 407 / 407II Users Guide - Page 47
RS-232C Interface Model
ON
ON
OFF No. 1 2 3 4 5 6 7 8 9 10
DIP-SW 1
OFF No. 1 2 3 4
DIP-SW 2
Switch 1-1 ON OFF
DIP-SW 1
The factory settings of switches 1-2 through 1-10 will change according to the command emulation that has been set using switche 1-1.
(1) Star mode
Switch
Function
1-1
Command emulation
1-2
Should not be changed (Should be set to on...
OKIPOS 407 / 407II Users Guide - Page 50
... DIP switch are all on . Switch 2-1~2-4
Function Always ON
DIP-SW 2
ON
The factory settings of DIP switch are all on .
OFF Should be set to on
- 46 - USB Interface Model
ON
OFF No. 1 2 3 4 5 6 7 8 9 10
DIP-SW 1
ON
OFF No. 1 2 3 4
DIP-SW 2
Switch 1-1 1-2 1-3 1-4 1-5 1-6
1-7 1-8 1-9 1-10
DIP-SW 1
Function Command emulation (Ster Line mode) Should...
OKIPOS 407 / 407II Users Guide - Page 51
... DIP switch are all on . Ethernet Interface Model
ON
OFF No. 1 2 3 4 5 6 7 8 9 10
DIP-SW 1
ON
OFF No. 1 2 3 4
DIP-SW 2
Switch 1-1 1-2 1-3 1-4 1-5 1-6
1-7 1-8 1-9 1-10
DIP-SW 1
Function Command emulation (Ster Line mode) Should not be changed (Should be set to on) Should not be changed (Should be set to on) Sensor adjustment Should not be changed...
OKIPOS 407 / 407II Users Guide - Page 52
...After the interface board has been initialized, the printer will flash with a regular pattern. LED Push Switch
11-5.
Wireless LAN Interface Model
ON
ON
OFF No. 1 2 3 4 5 6 7 8 9 10
DIP-SW 1
OFF No. 1 2 3...mode) Should not be changed (Should be set to on) Should not be changed (Should be set to on) Sensor adjustment Should not be changed (Should be set to on )
ON Always ON
Invalid Offline...
Oki OKIPOS407II Reviews
We have not received any reviews for Oki yet.