English Manual
Page 2
...NORDICTRACK is missing or illegible, see the front cover of ICON IP, Inc. 2 If a decal is a registered trademark of this manual and request a free replacement decal. Note: The decals may not be shown at actual size. TABLE OF CONTENTS WARNING DECAL PLACEMENT 2 IMPORTANT PRECAUTIONS 3 BEFORE YOU BEGIN 5 PART IDENTIFICATION CHART 6 ASSEMBLY... 7 OPERATION AND ADJUSTMENT 14 HOW TO FOLD AND MOVE THE TREADMILL 22 TROUBLESHOOTING 23 EXERCISE GUIDELINES 25 PART LIST 27 EXPLODED DRAWING 28 ORDERING...
...NORDICTRACK is missing or illegible, see the front cover of ICON IP, Inc. 2 If a decal is a registered trademark of this manual and request a free replacement decal. Note: The decals may not be shown at actual size. TABLE OF CONTENTS WARNING DECAL PLACEMENT 2 IMPORTANT PRECAUTIONS 3 BEFORE YOU BEGIN 5 PART IDENTIFICATION CHART 6 ASSEMBLY... 7 OPERATION AND ADJUSTMENT 14 HOW TO FOLD AND MOVE THE TREADMILL 22 TROUBLESHOOTING 23 EXERCISE GUIDELINES 25 PART LIST 27 EXPLODED DRAWING 28 ORDERING...
English Manual
Page 4
... experience pain while exercising, stop immediately and cool down. Inspect and properly tighten all parts of the treadmill by placing objects under the treadmill. 25. Never remove the motor hood unless instructed to move the treadmill. 23. DANGER: 27. Never insert any object into the off position (see the drawing on page... You must be performed by an authorized service representative. Do not attempt to do so by an authorized ser- When folding or moving the treadmill, make sure that the storage latch is properly assembled. (See ASSEMBLY on page 7 and HOW TO FOLD AND MOVE THE...
... experience pain while exercising, stop immediately and cool down. Inspect and properly tighten all parts of the treadmill by placing objects under the treadmill. 25. Never remove the motor hood unless instructed to move the treadmill. 23. DANGER: 27. Never insert any object into the off position (see the drawing on page... You must be performed by an authorized service representative. Do not attempt to do so by an authorized ser- When folding or moving the treadmill, make sure that the storage latch is properly assembled. (See ASSEMBLY on page 7 and HOW TO FOLD AND MOVE THE...
English Manual
Page 6
... parentheses below to see if it is preattached. The number following the key number is the quantity used for assembly. The number in the hardware kit, check to identify small parts used for assembly. Extra parts may be included. 5/16" Star Washer (8)-2 3/8" Star Washer (5)-10 3/8" Nut (3)-4 #8 x 3/4" Screw (6)-12...
... parentheses below to see if it is preattached. The number following the key number is the quantity used for assembly. The number in the hardware kit, check to identify small parts used for assembly. Extra parts may be included. 5/16" Star Washer (8)-2 3/8" Star Washer (5)-10 3/8" Nut (3)-4 #8 x 3/4" Screw (6)-12...
English Manual
Page 7
... to damage the Upright Wire. 1. 80 68 Cut 77 70 Hole Tie Cut 70 7 ASSEMBLY • Assembly requires two persons. • Place all assembly steps. • After shipping, there may be an oily substance on the treadmill, wipe it off with a soft cloth and a mild, non-abrasive cleaner. • Left...
... to damage the Upright Wire. 1. 80 68 Cut 77 70 Hole Tie Cut 70 7 ASSEMBLY • Assembly requires two persons. • Place all assembly steps. • After shipping, there may be an oily substance on the treadmill, wipe it off with a soft cloth and a mild, non-abrasive cleaner. • Left...
English Manual
Page 11
.... If they do not, turn one connector and try again. Start both Screws, and then tighten them. 9 Console Assembly 72 8 7 70 71 8 7 11 Console Wire 70 Console Assembly 70 71 Wire Tie Console Wire 9. Then, remove the wire tie from the Upright Wire. Insert the excess Upright Wire... that no wires are pinched. With the help of a second person, hold the console assembly near the Left Handrail (71) and 8 the Right Handrail (not shown). Attach the console assembly to the console wire. Set the console assembly on the Handrails (71, 72) with two 5/16" x 1" Screws (7) and two...
.... If they do not, turn one connector and try again. Start both Screws, and then tighten them. 9 Console Assembly 72 8 7 70 71 8 7 11 Console Wire 70 Console Assembly 70 71 Wire Tie Console Wire 9. Then, remove the wire tie from the Upright Wire. Insert the excess Upright Wire... that no wires are pinched. With the help of a second person, hold the console assembly near the Left Handrail (71) and 8 the Right Handrail (not shown). Attach the console assembly to the console wire. Set the console assembly on the Handrails (71, 72) with two 5/16" x 1" Screws (7) and two...
English Manual
Page 12
Identify the Left and Right Trays (45, 85). Tighten all of the Screws before tightening them. Be careful not to the console assembly with four #8 x 3/4" Screws (6). Attach the two Console Clamps (34) to overtighten the Screws. 85 45 6 6 6 6 12 See step 3. Orient the Trays as shown and attach each Tray 11 with four #8 x 3/4" Screws (6). Start all six 3/8" x 4" Screws (4). 10 Console Assembly 34 6 11. 10.
Identify the Left and Right Trays (45, 85). Tighten all of the Screws before tightening them. Be careful not to the console assembly with four #8 x 3/4" Screws (6). Attach the two Console Clamps (34) to overtighten the Screws. 85 45 6 6 6 6 12 See step 3. Orient the Trays as shown and attach each Tray 11 with four #8 x 3/4" Screws (6). Start all six 3/8" x 4" Screws (4). 10 Console Assembly 34 6 11. 10.