Enc Manual
Page 2
NORDICTRACK is a registered trademark of ICON Health & Fitness, Inc. 2 The BLUETOOTH® word mark and logos are used under license. IFIT is a registered trademark of ICON ... a trademark of this manual and request a free replacement decal. TABLE OF CONTENTS WARNING DECAL PLACEMENT 2 IMPORTANT PRECAUTIONS 3 BEFORE YOU BEGIN 7 PART IDENTIFICATION CHART 8 ASSEMBLY 9 HOW TO USE THE ELLIPTICAL 18 MAINTENANCE AND TROUBLESHOOTING 31 EXERCISE GUIDELINES 33 PART LIST 35 EXPLODED DRAWING 37 ORDERING REPLACEMENT PARTS Back Cover LIMITED WARRANTY Back Cover...
NORDICTRACK is a registered trademark of ICON Health & Fitness, Inc. 2 The BLUETOOTH® word mark and logos are used under license. IFIT is a registered trademark of ICON ... a trademark of this manual and request a free replacement decal. TABLE OF CONTENTS WARNING DECAL PLACEMENT 2 IMPORTANT PRECAUTIONS 3 BEFORE YOU BEGIN 7 PART IDENTIFICATION CHART 8 ASSEMBLY 9 HOW TO USE THE ELLIPTICAL 18 MAINTENANCE AND TROUBLESHOOTING 31 EXERCISE GUIDELINES 33 PART LIST 35 EXPLODED DRAWING 37 ORDERING REPLACEMENT PARTS Back Cover LIMITED WARRANTY Back Cover...
Enc Manual
Page 8
PART IDENTIFICATION CHART Use the drawings below each drawing is the quantity needed for assembly. The number in the hardware kit, check to identify the small parts needed for assembly. Extra parts may be included. M5 Washer (94)-2 M8 Washer (97)-8 M10 Split Washer (105)-8 16mm Wave Washer (54)-2 M8 Locknut (102)-4 M4...
PART IDENTIFICATION CHART Use the drawings below each drawing is the quantity needed for assembly. The number in the hardware kit, check to identify the small parts needed for assembly. Extra parts may be included. M5 Washer (94)-2 M8 Washer (97)-8 M10 Split Washer (105)-8 16mm Wave Washer (54)-2 M8 Locknut (102)-4 M4...
Enc Manual
Page 9
...you have Internet access, call Customer Service (see page 8. • In addition to the included tool(s), assembly requires the following tools: one Phillips screwdriver one rubber mallet Assembly may be easier if you do not use power tools. 1. Go to www.iconservice.ca/CustomerService/ ... Frame (1). 21 104 105 9 Attach the Rear Stabilizer (2) to prevent it from under the rear 2 of this step. ASSEMBLY • Assembly requires two persons. • Place all assembly steps. • Left parts are marked "L" or "Left" and right parts are marked "R" or "Right." • To...
...you have Internet access, call Customer Service (see page 8. • In addition to the included tool(s), assembly requires the following tools: one Phillips screwdriver one rubber mallet Assembly may be easier if you do not use power tools. 1. Go to www.iconservice.ca/CustomerService/ ... Frame (1). 21 104 105 9 Attach the Rear Stabilizer (2) to prevent it from under the rear 2 of this step. ASSEMBLY • Assembly requires two persons. • Place all assembly steps. • Left parts are marked "L" or "Left" and right parts are marked "R" or "Right." • To...
Enc Manual
Page 32
...89). Using a standard screwdriver, remove the Shield Cover (75) and the Shield Cover Cap (118). Then, see assembly step 16 on page 14 and remove the Right Pedal Arm (58) from the Left and Right Shields. Tighten the...you removed. To adjust the drive belt, first press the power switch to be adjusted. Next, see assembly step 15 on page 39. Then, remove the Right Shield. Then, retighten the Idler Screw. 113 89...the Large Axle Cover (53), and the M8 Washer (not shown) from the elliptical. Remove the M4 x 19mm Screws (5) and the M4 x 48mm Screw (107) from the Right Upper Body Leg (60...
...89). Using a standard screwdriver, remove the Shield Cover (75) and the Shield Cover Cap (118). Then, see assembly step 16 on page 14 and remove the Right Pedal Arm (58) from the Left and Right Shields. Tighten the...you removed. To adjust the drive belt, first press the power switch to be adjusted. Next, see assembly step 15 on page 39. Then, remove the Right Shield. Then, retighten the Idler Screw. 113 89...the Large Axle Cover (53), and the M8 Washer (not shown) from the elliptical. Remove the M4 x 19mm Screws (5) and the M4 x 48mm Screw (107) from the Right Upper Body Leg (60...
Enc Manual
Page 35
... Washer Small Axle Cover Roller Arm Bushing Arm Bearing Right Pedal Arm Right Roller Arm Right Upper Body Leg Right Upper Body Arm Grip Sensor Assembly/Wire Pedal Arm Axle Right Upper Body Arm Front Cover Right Upper Body Arm Rear Cover Left Upper Body Arm Front Cover Left Upper Body...
... Washer Small Axle Cover Roller Arm Bushing Arm Bearing Right Pedal Arm Right Roller Arm Right Upper Body Leg Right Upper Body Arm Grip Sensor Assembly/Wire Pedal Arm Axle Right Upper Body Arm Front Cover Right Upper Body Arm Rear Cover Left Upper Body Arm Front Cover Left Upper Body...
Enc Manual
Page 36
.... Qty. Shield Cover Cap Power Cord Ramp Axle Small Frame Bushing Clevis Pin Plastic Spacer M4 x 19mm Self-tapping Screw Bumper M8 x 14mm Shoulder Screw Assembly Tool Grease Packet User's Manual Incline Motor Wire Resistance Motor Wire Blue Wire Green Wire White Wire Note: Specifications are not illustrated. 36 Qty.
.... Qty. Shield Cover Cap Power Cord Ramp Axle Small Frame Bushing Clevis Pin Plastic Spacer M4 x 19mm Self-tapping Screw Bumper M8 x 14mm Shoulder Screw Assembly Tool Grease Packet User's Manual Incline Motor Wire Resistance Motor Wire Blue Wire Green Wire White Wire Note: Specifications are not illustrated. 36 Qty.