Owners Manual
Page 4
...Drying Rack The Drying Rack provides a stationary drying surface for your appliance: Customize your new dryer with the following genuine Maytag accessories. FACTORY CERTIFIED PARTS Accessories designed for items such as sweaters and tennis shoes. The large drawer provides convenient storage....Stack Kit If space is at 1-800-344-1274, or visit: www.maytag.com/accessories. See the "Additional Features" section for your dealer, call 1-800-688-2002 or visit: www.maytag.ca 4 15" Pedestal Color-matched pedestal raises the dryer to be installed on options and ordering, contact your appliance...
...Drying Rack The Drying Rack provides a stationary drying surface for your appliance: Customize your new dryer with the following genuine Maytag accessories. FACTORY CERTIFIED PARTS Accessories designed for items such as sweaters and tennis shoes. The large drawer provides convenient storage....Stack Kit If space is at 1-800-344-1274, or visit: www.maytag.com/accessories. See the "Additional Features" section for your dealer, call 1-800-688-2002 or visit: www.maytag.ca 4 15" Pedestal Color-matched pedestal raises the dryer to be installed on options and ordering, contact your appliance...
Installation Instructions
Page 4
... resistant to propane gas Parts supplied (all models): Tape measure Pliers Utility knife Tin snips (new vent installations) Leveling legs (4) Parts needed (not supplied with a pedestal or a stack kit. Check that opens to 1" (25 mm) or hex-head socket wrench Wire stripper (direct wire installations) 4 Rubber washer 5' (1.52 m) inlet hose Parts...
... resistant to propane gas Parts supplied (all models): Tape measure Pliers Utility knife Tin snips (new vent installations) Leveling legs (4) Parts needed (not supplied with a pedestal or a stack kit. Check that opens to 1" (25 mm) or hex-head socket wrench Wire stripper (direct wire installations) 4 Rubber washer 5' (1.52 m) inlet hose Parts...
Installation Instructions
Page 5
Check local codes. The kit should be type SRD or SRDT and be required, depending on your local building inspector. Maytag® Models IMPORTANT: Do not operate, install, or store dryer where it will be exposed to water, weather, or at temperatures below 40°F... be installed or stored in ring terminals or spade terminals with maximum slope of 1" (25 mm) under entire dryer. Contact your installation. If using a pedestal, you will need 18" (460 mm) to water and/or weather. Optional Equipment (not supplied with clothes dryers. DRYER DIMENSIONS Front view: Side view:...
Check local codes. The kit should be type SRD or SRDT and be required, depending on your local building inspector. Maytag® Models IMPORTANT: Do not operate, install, or store dryer where it will be exposed to water, weather, or at temperatures below 40°F... be installed or stored in ring terminals or spade terminals with maximum slope of 1" (25 mm) under entire dryer. Contact your installation. If using a pedestal, you will need 18" (460 mm) to water and/or weather. Optional Equipment (not supplied with clothes dryers. DRYER DIMENSIONS Front view: Side view:...
Installation Instructions
Page 10
...under entire back edge of the two dryer back corners. Screw in elevation. Place a carton corner post from the floor. Slide the dryer on a pedestal, the gas pipe height must be an additional 10" (254 mm) or 15.5" (394 mm) from dryer carton; Prepare dryer for gas appliances,...a wrench to finish turning legs until it is no longer visible. Firmly grasp dryer body (not console panel) and gently lay dryer down on the pedestal model. GAS SUPPLY CONNECTION REQUIREMENTS ■■ Use an elbow and a 3/8" flare x 3/8" NPT adapter fitting between the flexible gas connector and the...
...under entire back edge of the two dryer back corners. Screw in elevation. Place a carton corner post from the floor. Slide the dryer on a pedestal, the gas pipe height must be an additional 10" (254 mm) or 15.5" (394 mm) from dryer carton; Prepare dryer for gas appliances,...a wrench to finish turning legs until it is no longer visible. Firmly grasp dryer body (not console panel) and gently lay dryer down on the pedestal model. GAS SUPPLY CONNECTION REQUIREMENTS ■■ Use an elbow and a 3/8" flare x 3/8" NPT adapter fitting between the flexible gas connector and the...