Maytag MGD7100DC Support and Manuals
Get Help and Manuals for this Maytag item
View All Support Options Below
Free Maytag MGD7100DC manuals!
Problems with Maytag MGD7100DC?
Ask a Question
Free Maytag MGD7100DC manuals!
Problems with Maytag MGD7100DC?
Ask a Question
Popular Maytag MGD7100DC Manual Pages
Use & Care Guide - Page 5
...n Use the shortest length of time set and sometimes results in the load.... that use steam. each load. Service calls caused by improper venting are ...Installation Instructions supplied with 4" (102 mm) diameter heavy, rigid vent material. Use Timed Dry for smoothing out wrinkles and reducing odors from the dryer.
n Replace plastic or foil vent material
with your steam dryer (on some models...
Use & Care Guide - Page 7
...some models), Bedding (on some models), and Wrinkle Control (on the type of a Timed Dry or Rapid Dry cycle. On 2-digit displays, for the Bedding cycle, as a reminder to manually reposition ...off the Energy Saver option. See "Cycle Guide" for Normal.
Follow garment label instructions. NOTE: Sensor Cycles use with High or Medium heat settings. Dryness Level When using a slightly lower ...
Use & Care Guide - Page 8
... starting with high heat, which has been proven to about 1/2 full. CYCLE GUIDE - This is time to rearrange items for that cycle. Large load: Fill ...settings.
* On steam models only. U ses a stepped drying temperature from Medium to tumble freely.
8 Not all settings and options are default settings for optimal drying.
† On steam models, you may select the "With Steam" setting...
Use & Care Guide - Page 9
... steam cycle after 60 minutes. Not all settings and options are unsure of 3-4 items.
† On steam models, you select a Timed Cycle, the time appears in 1-minute increments. Large load: Fill the dryer drum up to about 1/2 full. CYCLE GUIDE - Adjusting drying time on some knits.
CYCLE GUIDE - STEAM CYCLE (on Timed Cycles
When...
Use & Care Guide - Page 12
...error... "Troubleshooting" section.
Check Lint Screen The Check Lint Screen indicator will light when the drying cycle is not available on model. ...the cycle by using the Air Only setting or Air Dry cycle, depending on all models. Items containing foam, rubber, or plastic... or opening and press down fully into holes. Rest the rear support on if a blocked vent or low airflow issue is lit. ...
Use & Care Guide - Page 15
...Installation Instructions.
15 START/PAUSE not touched firmly or held long enough. Household fuse is blown or circuit breaker has tripped. Supply line valve not open .
Check with a qualified electrician. Replace the fuses or reset the circuit breaker. If the problem...balled up in "Cycle Guide." Hold your hand under... installed.
Water pump or water inlet valve (depending on model)...
Use & Care Guide - Page 16
... properly connected with water and heat. The load may experience underdrying. Use 4" (102 mm) diameter vent material. See "Cycle Guide."
Proper operation of the door. See the Installation Instructions. Lint on Sensor Cycles.
Steam models only: For steam cycles, the water is too large and heavy to tumble freely. Do not use it is...
Use & Care Guide - Page 17
... between F# and E#, the dryer control has detected a problem that water
the water is connected to the dryer. Steam models only: For steam cycles, Make sure water is in garments after wearing, select Refresh. Check that requires service. Touch any setting or option name to clear the code from loads left in need of cycle complete...
Use & Care Guide - Page 18
... Care Guide, scan the QR code on the below named parts only and does not include repair labor. Please take a few minutes to review the Troubleshooting or Problem Solver section of product replacement, your retailer about the quality, durability, or need for factory specified parts and repair labor to determine if another warranty applies. Before contacting us to arrange service, please...
Warranty Information - Page 1
...Guide, scan the QR code on the below named parts only and does not include repair labor. Please take a few minutes to review the Troubleshooting or Problem Solver section of the original unit's warranty period. Service...product maintenance or installation,
installation not in which it was purchased, or at its sole discretion replace the product. This warranty gives you specific legal rights,...
Installation Guide - Page 7
... 20- GROUNDING INSTRUCTIONS
I For a grounded, cord-connected dryer: This dryer must be grounded. grounding conductor can result in doubt as to whether the dryer is located on the model/serial rating plate for electric current.
LP Gas Conversion:
IMPORTANT: Conversion must have the correct burner for use Power Supply Cord Replacement Part Number 8529008...
Installation Guide - Page 8
...gas supply line with the B149.1, Natural Gas and Propane Installation Code. Option 2 (Alternate Method) Approved aluminum or copper tubing... m), use larger pipe.
In Canada: An individual manual shut-off valve
GAS SUPPLY CONNECTION REQUIREMENTS ■■... additional 18" (460 mm) from the floor, depending on the pedestal model. D
B
A. 3/8" flexible gas connector B. 3/8" pipe to the rigid...
Installation Guide - Page 15
...water faucets are for certain part replacement or repair. q Check dryer's final location.
All Models:
q Select a Timed ...INSTALLATION CHECKLIST
q Check that all parts are registered trademarks of Acument Intellectual Properties, LLC.
15
The odor will not start, check the following instructions are on . Be sure vent is closed.
q Dispose of/recycle all of your Use and Care Guide...
Dimension Guide - Page 1
...39" Max. (990 mm)
Bottom view: Back view:
61/4" (159 mm)
Recommended Installation Spacing:
53/4"* (146 mm)
Water inlet
(Steam Models Only)
Vent
297/8"* (759 mm)
31/2"* (89 mm)
Gas
3/4"* (18 mm)... closet installation, with a door, minimum ventilation openings in .2 min. (155 cm2) 3" (76 mm)
1" (25 mm)
1" (25 mm)
NOTE: Most installations require a minimum of installation and servicing.
&#...
Dimension Guide - Page 2
...installed within 6 ft (1.8 m) of the dryer in longer drying times and increased energy usage. ELECTRICAL REQUIREMENTS
A 120-volt, 60 Hz, AC-only, 15 or 20 amp fused electrical supply is required. Exhaust hood must be used for lengths under 20 ft (6.1 m).
Specifications subject to the gas supplier and local codes...complete details, see Installation Instructions packed with product.
Maytag MGD7100DC Reviews
We have not received any reviews for Maytag yet.