Maytag MEDB850WL - 29" Electric Dryer Support and Manuals
Get Help and Manuals for this Maytag item
View All Support Options Below
Free Maytag MEDB850WL manuals!
Problems with Maytag MEDB850WL?
Ask a Question
Free Maytag MEDB850WL manuals!
Problems with Maytag MEDB850WL?
Ask a Question
Most Recent Maytag MEDB850WL Questions
How Do You Change The Blower Belt?
How do you change the blower belt?
How do you change the blower belt?
(Posted by michelledlowry 11 years ago)
Popular Maytag MEDB850WL Manual Pages
Owners Manual - Page 5
....
2. TIMED DRY - RAPID DRY -
Press POWER/CANCEL.
2. Your dryer may not have all of the cycles and features described. See the "Sensor Preset Cycle Settings."
Press TIME ADJUST + (plus ) or - (minus) buttons until the desired temperature illuminates.
5.
Press START/PAUSE.
5 QUICK START GUIDE
NOTE: This Use and Care Guide covers several different models.
WARNING: To...
Owners Manual - Page 6
... fabrics
Extra-Low
*Preferred setting
6 Cycle tips ■ Dry most loads using the preset cycle settings.
■ Refer to the load you may select an alternate drying temperature by pressing DRYNESS LEVEL and choosing More, Normal, Less, or Damp.
Follow package instructions.
■ To reduce wrinkling, remove the load from the dryer as soon as an...
Owners Manual - Page 7
... the dryer will continue to select a specific amount of Load
Time* (Minutes)
Foam rubber - Once a Dryness Level is best for touching up clothes that can be used with Sensor Cycles.
7 Once the alternate temperature has been selected, the next time the same cycle is selected, the alternate temperature is not available with the drying rack...
Owners Manual - Page 8
... "Options." Dry The Dry light illuminates when the drying cycle is available only with the drying Status indicator lights. Drum Light option
On some models, select Drum Light to turn the drum light ON or OFF.
The Damp Dry Signal is useful when you do not select the Wrinkle Prevent/Wrinkle Prevent Plus setting, the dryer stops after...
Owners Manual - Page 9
... affect all Sensor cycles. The dryer starts at the front of the manual or contact the dealer from whom you purchased your model allows drying rack usage and for all of your model does not have a drying rack, you do not press Start/Pause within 5 minutes of the drying rack.
4.
Press START/PAUSE to different installations, environmental conditions, or personal preference...
Owners Manual - Page 10
... would obstruct the flow of lint screen with your load is hard to remove.
2. Time* (minutes)
Wool Sweaters
Timed Dry Low
60
Block to remove lint. Replace screen in the dryer. Doing so can be rack dried and the suggested cycle, temperature setting, and drying time. Actual drying time will depend on the drying rack.
The lint screen is in...
Owners Manual - Page 11
...dryer again 1. Disconnect wiring. 3. Reinstalling the dryer Follow the "Installation Instructions" to secure dryer door. When replacing your dryer. Shut off water faucet. 3. Cleaning the Dryer Interior
1. Steam Models ...more often, depending on vacation or not using your dryer where it . Replace all parts and panels before servicing. Make sure leveling legs are found. NOTE: Garments ...
Owners Manual - Page 12
... ? otherwise, press POWER/CANCEL and then start a new drying cycle.
■ "F" Variable (F1, F2, F20, etc.) service codes: Call for the dryer. Replace the fuse or reset the circuit breaker.
Refer to possibly avoid the cost of lint and debris. www.maytag.com/help - In Canada www.maytag.ca
Dryer Operation
■ Is the clothing knotted or balled...
Owners Manual - Page 14
..., rewash and dry the clothing.
■ Is the dryer being used for product service if your home.
7. Replacement parts or repair labor if this information on the model and serial number label located on major appliances with electrical or plumbing codes, or use your major appliance, unless such damage results from defects in which it is installed in an...
Installation Instructions - Page 4
...dryer door to open . If a closet door or louvered door is greater than 1" (25 mm), install Extended Dryer Feet Kit, Part Number 279810. Some codes limit, or do not permit, installing dryer...;■ For closet installation, with elbow. See "Electrical Requirements."
■■ Floor must support dryer weight of 200 lbs. (90.7 kg). LOCATION REQUIREMENTS
INSTALLATION CLEARANCES Location must be...
Installation Instructions - Page 12
... may be used for best drying performance and to avoid sagging and kinking that may obstruct exhaust (such as flowers, rocks, bushes, or snow). Replace plastic or metal foil vents with lint.
Flexible metal vent: (Acceptable only if accessible to clean)
■■ Must be fully extended and supported in final dryer location.
■■...
Installation Instructions - Page 13
...
Refer to connect elbows H. Vent length necessary to the manufacturer's instructions. Contact your local dealer to exhaust through the bottom. Elbow C. Over-the-top installation (also available with dryer vent to wall vent mismatch): Part Number 4396037 - 0" (0 mm) to 18" (460 mm) mismatch
P art Number 4396011 - 18" (460 mm) to 29" (737 mm) mismatch...
Installation Instructions - Page 14
...best drying performance:
■■ Use following Vent System Chart to determine type of vent material and hood combinations acceptable to dryer location using straightest path possible.
Run vent to use.
INStall VENT SYSTEM
1. CONNECT INLET HOSES
For non-steam models...washer from inlet hose and replace with new rubber washer provided.
12" min. (305 mm)
Install exhaust hood and use ...
Installation Instructions - Page 17
... on console and any dust. Do not select Air Only Temperature setting. See "Troubleshooting". Remove the door assembly 1. q For power supply cord installation, plug into screw holes in your dryer vent may clog different parts of a water softener is first heated. All Models:
q Select a Time Dry heated cycle, and start , check the following:
• Controls are on...
Installation Instructions - Page 19
...See "Installation Instructions".
■■ Are fabric softener sheets blocking the grille? Proper operation of dryer cycles requires temperatures above 45°F (7°C).
T ry the following :
Was the drying cycle interrupted by a power failure? Confirm the exterior vent exhaust hood is present. Replace the fuse or reset the circuit breaker.
If the problem continues, call...
Maytag MEDB850WL Reviews
We have not received any reviews for Maytag yet.