Service Manual
Page 7
...washer in marked areas of the washer. Remove the accessory package from the outside of the carton. GENERAL INFORMATION 1-1 UNCRATING INSTRUCTIONS NOTE: The following steps must be reinforced to the troubleshooting section for more information regarding a solution for electrical service. • Standpipe Drain...load situations. For all installations the drain hose must be elevated to the washer. 2. Refer to minimize vibration from the washer...1998 Maytag Corporation SECTION 1. A 36" high standpipe is the responsibility of less than 20 P.S.I . NOTE: If drain ...
...washer in marked areas of the washer. Remove the accessory package from the outside of the carton. GENERAL INFORMATION 1-1 UNCRATING INSTRUCTIONS NOTE: The following steps must be reinforced to the troubleshooting section for more information regarding a solution for electrical service. • Standpipe Drain...load situations. For all installations the drain hose must be elevated to the washer. 2. Refer to minimize vibration from the washer...1998 Maytag Corporation SECTION 1. A 36" high standpipe is the responsibility of less than 20 P.S.I . NOTE: If drain ...
Service Manual
Page 19
...tumbles. Clothes Wet at the end of clothing loads, available water pressure and the time for the door lock system to reduce the suds present (See Troubleshooting & Diagnosis - GENERAL INFORMATION 1-13 Cotton/ ...Sturdy 7/3 Easy Care/ Perm Press 5/3 D e licat e s 6/ 2 4 Hand W ashab les 3/ 2 7 16008373-01 © 1998 Maytag... will go into a suds reduction routine, consisting of a series of additional rinse and partial drain cycles to retract at End of suds. The washer will vary based on -M ax Ex t ra ct ...
...tumbles. Clothes Wet at the end of clothing loads, available water pressure and the time for the door lock system to reduce the suds present (See Troubleshooting & Diagnosis - GENERAL INFORMATION 1-13 Cotton/ ...Sturdy 7/3 Easy Care/ Perm Press 5/3 D e licat e s 6/ 2 4 Hand W ashab les 3/ 2 7 16008373-01 © 1998 Maytag... will go into a suds reduction routine, consisting of a series of additional rinse and partial drain cycles to retract at End of suds. The washer will vary based on -M ax Ex t ra ct ...
Service Manual
Page 36
... VDC and 120 VAC circuits. 16008373-01 © 1998 Maytag Corporation SECTION 3. Apply sound dampening pad to start different operations, such as drain, fill, tumble and spin. If a switch is stuck....a stuck button on side of the timer input wires leading from the timer to P3(1). TROUBLESHOOTING 3 - 2 Replace door lock mechanism if necessary. Third Rinse Cycle Is Always Cold: If... is activated during an unbalanced load condition. If the circuit is OPEN, the board will not respond properly. If the switch is stuck, the washer will check the rinse temperature selection...
... VDC and 120 VAC circuits. 16008373-01 © 1998 Maytag Corporation SECTION 3. Apply sound dampening pad to start different operations, such as drain, fill, tumble and spin. If a switch is stuck....a stuck button on side of the timer input wires leading from the timer to P3(1). TROUBLESHOOTING 3 - 2 Replace door lock mechanism if necessary. Third Rinse Cycle Is Always Cold: If... is activated during an unbalanced load condition. If the circuit is OPEN, the board will not respond properly. If the switch is stuck, the washer will check the rinse temperature selection...
Service Manual
Page 48
Washer Wattages: The following wattages are approximate and without clothes: Function: Delay Tumbling (empty) & water fill Tumbling (Full-Wash level) Tumbling (Full-Rinse Level) Draining (No tumble) with nominal running amperage at a maximum of 5.0 amps. TROUBLESHOOTING 3 - 1 4 Peak amperage is 7.5 amps during acceleration to 0.10 Kwh per cycle...water Draining (No tumble) no water Spinning (100 rpm) Spin Acceleration (100-200 rpm) Spinning (400 rpm) Spinning (850 rpm) Wattages: 10-15 50-70 110-120 140-150 45-50 30-35 85-90 130-150 160-170 400-410 16008373-01 © 1998 Maytag ...
Washer Wattages: The following wattages are approximate and without clothes: Function: Delay Tumbling (empty) & water fill Tumbling (Full-Wash level) Tumbling (Full-Rinse Level) Draining (No tumble) with nominal running amperage at a maximum of 5.0 amps. TROUBLESHOOTING 3 - 1 4 Peak amperage is 7.5 amps during acceleration to 0.10 Kwh per cycle...water Draining (No tumble) no water Spinning (100 rpm) Spin Acceleration (100-200 rpm) Spinning (400 rpm) Spinning (850 rpm) Wattages: 10-15 50-70 110-120 140-150 45-50 30-35 85-90 130-150 160-170 400-410 16008373-01 © 1998 Maytag ...
Service Manual
Page 92
...Easy Care/ Perm Press Delicates Hand Washables 7/3 5/3 6/24 3/27 16010199 (16008373-03) 5 Revised 7/00 ©2000 Maytag Appliances Sales Company The main wash times listed include 2 minutes ...drain cycles to retract at End of the cycle. 3. The total cycle times are approximate and will go into a suds reduction routine, consisting of a series of pause between tumbles. The washer... will vary based on water fill times, due to types of clothing loads and the time for the door lock system to reduce the suds present. (See Troubleshooting...
...Easy Care/ Perm Press Delicates Hand Washables 7/3 5/3 6/24 3/27 16010199 (16008373-03) 5 Revised 7/00 ©2000 Maytag Appliances Sales Company The main wash times listed include 2 minutes ...drain cycles to retract at End of the cycle. 3. The total cycle times are approximate and will go into a suds reduction routine, consisting of a series of pause between tumbles. The washer... will vary based on water fill times, due to types of clothing loads and the time for the door lock system to reduce the suds present. (See Troubleshooting...