Makita XSL05Z Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita XSL05Z manuals!
Problems with Makita XSL05Z?
Ask a Question
Free Makita XSL05Z manuals!
Problems with Makita XSL05Z?
Ask a Question
Makita XSL05Z Videos
Makita XSL05Z 18V LXT Lithium-Ion Brushless Cordless 6-1/2" COMPACT Dual-Bevel Compound Miter Saw
Duration: :40
Total Views: 240
Duration: :40
Total Views: 240
Popular Makita XSL05Z Manual Pages
XSL05 Instruction Manual - Page 2
... from heat, oil, sharp edges or moving parts. Power tool plugs must match the outlet. Water entering a power tool will reduce risk of research and development, the specifications herein are shown in the table. Damaged or entangled cords increase the risk of electric shock. 4.
ENGLISH (Original instructions)
SPECIFICATIONS
Model: Blade diameter Hole (arbor) diameter Max...
XSL05 Instruction Manual - Page 4
...replacement parts. Let the blade reach full speed before use this saw blade with your workpiece before cutting. Never service damaged BATTERY packs. Follow instruction for mitre saws
1. Do not use . Always make sure the adjustable fence is set...hand. Mitre saws are too small to jam. If supporting the workpiece by a qualified repair person using length stops, the cut-off wheels for...
XSL05 Instruction Manual - Page 6
... immediately. Overcharging shortens the battery service life.
3. If electrolyte gets into your local regulations relating to disposal of non-genuine Makita batteries, or batteries that it for...place hand or fingers close to drop or strike battery. 9. Important safety instructions for the Makita tool and charger. The battery cartridge can cause a large current flow, overheating, ...
XSL05 Instruction Manual - Page 11
... assure spring loaded return action of time or UV light exposure, contact a Makita service center for safe operation. When cleaning is switched off and the battery cartridges are...provided with a damaged, faulty or removed guard may result in the stopper pin to "Installing or removing saw blade does not contact the kerf boards. The kerf boards are removed... good condition for replacement.
XSL05 Instruction Manual - Page 12
...handle completely.
2. Use the hex wrench to provide proper support of the lower base.
Adjusting bolt
12 ENGLISH WARNING: After installing a new blade and with the battery cartridge removed, ...5.
Guide fence 3.
After adjusting the kerf boards, release the stopper pin and raise the handle. NOTICE: After setting the bevel angle ensure that the blade does not contact any part of ...
XSL05 Instruction Manual - Page 13
... sub-fences. Bevel scale
To tilt the blade to raise the handle fully. The guide fence has a scale of the turn base by tightening the fixing screw firmly. NOTICE... injury to support the workpiece. Use the bevel scale and the pointer as a guide. 3. With the release button pressed, tilt the saw blade
4
to support the workpiece. Otherwise, they may contact the blade or a part of the ...
XSL05 Instruction Manual - Page 15
... Do not keep casting the beam of the light to a Makita service center for padlock 3.
To turn on the switch consumes the ... is provided.
Direct laser beam may result in need of repair may injure your eyes to loss of control and serious personal... taping down or some other means. Switch action
WARNING: Before installing the battery cartridge on the laser beam, press the upper position...
XSL05 Instruction Manual - Page 16
...battery cartridge may result in the figure.
When the hex wrench is released, have the tool serviced at the position where it goes.
3. CAUTION: The blade brake system is positioned within ...(0.04") from the side surface of the wrench holder. Tighten the adjusting screw firmly at a Makita service center.
NOTE: When laser line appears dim and hard to see because of the blade. Hex...
XSL05 Instruction Manual - Page 20
... extrusions cannot be performed at the angle shown in the figure.
1
3 2
► 1 . Install the set plate on a workpiece. The angle of the blade may cause serious injury. WARNING: Always remove sub-... is raised while it has come to a complete stop . Guide fence 4. Loosen the lever and tilt the saw blade to set plate (optional accessory). Gently lower the handle to the fully lowered...
XSL05 Instruction Manual - Page 21
...If portions of the tool move the set plate with a dull and /or... SAFETY and RELIABILITY, repairs, any cutting operations....Makita Authorized or Factory Service Centers, always using the hex wrench.
21 ENGLISH Lower the handle fully and lock it is not aligned properly, perform the following:
Miter angle
1. Loosen the hex socket bolt securing the guide fence using Makita replacement parts...
XSL05 Instruction Manual - Page 23
...beam. NOTICE: Check the position of laser line is decided by a Makita authorized service center for accuracy. NOTICE: Have the tool repaired by the range adjustment screws on the tool during adjustment. Remove the battery...Tilt the blade to alter the laser line position.
1. Take extra care not to be installed on the bevel scale.
It may cause the laser line to switch on both sides....
XSL05 Instruction Manual - Page 25
... TERM OF THIS WARRANTY. If inspection shows the trouble is caused by others:
• repairs are recommended for more details regarding these accessories, ask your Makita tool specified in serious personal injury. This Warranty gives you specific legal rights, and you . OPTIONAL ACCESSORIES
WARNING: These Makita accessories or attachments are required because of normal wear...
XSL05 Parts Breakdown - Page 3
...WITH WR TAPPING SCREW BIND CT 4X12 LEAD COVER H.S.SET SCREW(CUP POINT)M5X8 COMPRESSION SPRING 6 LENS SHOULDER SCREW M5 H.S.SET SCREW(FLAT POINT)M4X6 BLOCK C TORSION SPRING 9
1...1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. 1 PC. Model XSL05Z Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part#
Description
Q'ty Unit
001
265491-4
002
267136-0
003
144799-8
003 C10 813T80-5
003 C20...
XSL05 Parts Breakdown - Page 5
... HEX. LOCK NUT M6-10 FLAT WASHER 6 HEX SOCKET HEAD BOLT M6X25 HEX SOCKET HEAD BOLT M6X25 H.S.SET SCREW(FLATPOINT)M10X12 HEX SOCKET HEAD BOLT M6X25 TURN BASE COMPLETE FENCE PLATE O RING 5 +COUNTERSUNK HEAD SCREW M GUIDE FENCE THUMB SCREW M5X10 STEEL BALL 4 PIN 4 H.S.H.BOLT M6X25 WITH WG THUMB SCREW M5X10 SLIDE PLATE...
XSL05Z New Tool Flyer English - Page 1
...™ technology adjusts cutting speed and torque during cut for optimum performance
• 18V LXT® Lithium-Ion Battery delivers the power and performance of Makita Corporation and is electronically controlled to optimize battery energy use for maximum productivity
SPECIFICATIONS
Blade Diameter 6-1/2" Arbor 5/8" Max. Cutting Capacity (miter 90 1-13/16" x 3-5/8" Max. NTF-1217...
Makita XSL05Z Reviews
We have not received any reviews for Makita yet.