Makita 5007MG Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita 5007MG manuals!
Problems with Makita 5007MG?
Ask a Question
Free Makita 5007MG manuals!
Problems with Makita 5007MG?
Ask a Question
Makita 5007MG Videos
Makita 5007mg Review - Popular Circular Saw Reviews
Duration: 1:03
Total Views: 425
Duration: 1:03
Total Views: 425
Serra circular makita 5007MG
Duration: 10:22
Total Views: 1,488
Duration: 10:22
Total Views: 1,488
Makita 7-1/4 in. Magnesium Circular Saw - 5007MG
Duration: 1:02
Total Views: 361
Duration: 1:02
Total Views: 361
Makita 5007MG Circular Saw
Duration: 1:30
Total Views: 5,624
Duration: 1:30
Total Views: 5,624
Popular Makita 5007MG Manual Pages
Flyer (English) - Page 1
7-1/4" MAGNESIUM CIRCULAR SAWS
MAGNESIUM COMPONENTS CREATE LIGHTWEIGHT SAWS THAT ARE WELL-BALANCED AND JOBSITE TOUGH
Large Cutting and Bevel Capacities with Positive Stops at 22.5° and 45° Built-in LED Lights and Dust Blower Enhance the Line of Cut for Increased Accuracy* Reinforced Power Cord Withstands Jobsite Abuse Blade Wrench is Attached to Saw for Fast and...
Flyer (English) - Page 2
...Cutting Capacity at 90° Max. 7-1/4" MAGNESIUM CIRCULAR SAWS
Models 5007MG / 5007MGA / 5377MG
FEATURES & BENEFITS
■ Make quick, one-handed adjustments using large, rubberized levers ■ Large cutting and bevel capacities with positive stops at 22.5° and 45° ■ Reinforced power cord withstands jobsite abuse and lowers repair costs ■ Built-in LED lights illuminate...
Owners Manual - Page 2
... tools or pull the plug from country to follow all instructions. Loose clothes, jewelry, or long hair can cause you are rated for the three wire
grounded power cord and grounded power supply
system.
5. Carrying tools with grounded surfaces such as in any way. ENGLISH
SPECIFICATIONS
Model
5007MG / 5007MGA
Blade diameter
185 mm (7-1/4")
at 56°
35 mm (1-3/8")
No...
Owners Manual - Page 3
... at all times. Properly maintained tools with product (gained from the power source before using an extension cord, be repaired.
18. Tool service must be sure to use this manual. Table 1 shows the correct size to circular saw blade. The smaller the gage number, the heavier the cord. Table 1: Minimum gage for appropriate conditions. Wait until blade stops...
Owners Manual - Page 4
...parts of the tool "live " wire will cause the saw motionless in motion or KICKBACK may be retracted manually only for the blade to see that do support... the saw backward while the blade is accidentally dropped, lower guard may occur. Supports must be serviced before ...parts, gummy deposits, or a buildup of the saw teeth are not engaged into the material. If saw blade in its own cord...
Owners Manual - Page 5
... jump backwards over your hand or fingers behind the saw could cause personal injury. Place the wider portion of the saw base on that part of a board, and Fig. 6 the WRONG ...is solidly supported, not on the section that will not be caught on blades slows saw can cause KICKBACK. Fig. 4 illustrates typical hand support of proper hand support, workpiece support, and supply cord routing.
16...
Owners Manual - Page 6
...the circular saw held upside down in this instruction manual may be sure that no load speed
Class II Construction .../min revolutions or reciprocation per
minute
FUNCTIONAL DESCRIPTION
Fig. 7
18.
Before setting ... cleaner, safer cuts, set cut 2
007326
1. Fig. 6
17. This is switched off and unplugged before adjusting or checking function on the depth guide and move the base up...
Owners Manual - Page 7
... it stops and secure the base with the lever.
Setting bevel angle
Loosen the lever and tentatively set the tool base at a Makita service center.
The lamp lights up when the tool is not... Lever 2. when the arrow points 56, it points one of light
directly.
Electric brake
For model 5007MGA only
This tool is obtained. NOTE:
• Use a dry cloth to it can be adjusted...
Owners Manual - Page 8
... the motor and dangerous kickback, possi-
Removing or installing saw , they cannot be cut line.
Use both to dangerous kickback and possible serious injury. Set the base on the han- Now simply move the...wait until it on the tool. Rip fence (Guide rule)
To install the blade, follow your speed of the tool. • Use only the Makita wrench to turn the tool on new cut line,...
Owners Manual - Page 9
... tool specified in the holders. The use with the base using Makita replacement parts.
007333
1.
Use only identical carbon brushes. Should any assistance for more details regarding these accessories, ask your local Makita Service Center.
• Steel & Carbide-tipped saw blades
006549
Combination
General purpose blade for accuracy of original purchase. MAINTENANCE
CAUTION:
•...
Owners Manual - Page 10
... been made or attempted by others: • repairs are required because of incidental or consequential damages, so the above limitation may also have been made to the tool. IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES FROM THE SALE OR USE OF THE PRODUCT. Some states do...
Parts Breakdown - Page 2
... 15, LS1011N BALL BEARING 6002DDW,BO5001 URETHANE WASHER 26, 5007MG BLADE CASE SET, 5007MG MAKITA LOGO PLATE, 5007MG P.H. NUT M8-13, 5007MG BOW STOP RING E-12, 5007MG REAR COVER SET, 5007MG REAR COVER SET, 5007MG
TAPPING SCREW PT 4X18, MT240 MAKITA LOGO LABEL, 5007MG P.H. WASHER 8, 5037NB LEVER 56, 5007MG HEX. Parts Breakdown
5007MG
Products with multiple versions are listed in subsiding order...
Parts Breakdown - Page 3
...94530
158279-8 824772-1 804584-8
Parts Breakdown
LEVER 56, 5007MG HEX. LABEL, 5007MG
5007MG
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1
Page 3 of 3
8/18/2010 WASHER 5, JR3000V H.S.H. WASHER 8, 5037NB ANGULAR GUIDE, 5007MG SHOULDER PIN 6-7, 5007MG N/A
SLEEVE 6, 5007MG F. WASHER 5, 5012B, 6891D F. WASHER 7, JR3010 SPACER, 5007MG GUIDE RULE, 4200H HEX WRENCH 6, 3705...
Makita 5007MG Reviews
We have not received any reviews for Makita yet.