Makita GS5000 Support and Manuals
Get Help and Manuals for this Makita item
This item is in your list!
View All Support Options Below
Free Makita GS5000 manuals!
Problems with Makita GS5000?
Ask a Question
Free Makita GS5000 manuals!
Problems with Makita GS5000?
Ask a Question
Popular Makita GS5000 Manual Pages
Owners Manual - Page 1
INSTRUCTION MANUAL MANUEL D'INSTRUCTION MANUAL DE INSTRUCCIONES
Straight Grinder Meuleuse Droite Esmeril recto
GS5000 GS6000
DOUBLE INSULATION DOUBLE ISOLATION DOBLE AISLAMIENTO
013595
IMPORTANT: Read Before Using. IMPORTANT: Lire avant usage. IMPORTANTE: Leer antes de usar. 1
Owners Manual - Page 2
...rotating part ...abuse the cord. ENGLISH (Original instructions)
SPECIFICATIONS
Model
GS5000
GS6000
Maximum wheel capacity (diameter...support cover Without support cover
5.0 kg (11.1 lbs) 4.9 kg (10.7 lbs)
5.2 kg (11.5 lbs) 5.0 kg (10.9 lbs)
• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications...
Owners Manual - Page 3
... follow all safety warnings, instructions, illustrations and specifications provided with this power tool. The smaller the gage number, the heavier the cord. More Than Not More Than
AWG
0
6
18
16
16
14
6
10
18
16
14
12
10
12
16
16
14
12
12
16
000300
14
GEB108-4
STRAIGHT GRINDER SAFETY
WARNINGS
2. Safety Warnings...
Owners Manual - Page 4
...any other liquid coolants may make exposed metal parts of the wheel that require liquid coolants....if proper precautions are not specifically designed and recommended by insulated gripping surfaces only, when .... The eye protection must match the grinder spindle thread. Do not run the power... at maximum no-load speed for damage or install an undamaged accessory. As appropriate, wear dust ...
Owners Manual - Page 5
...Specific for the selected wheel. Wheel intended for larger power tool is not suitable for this
instruction manual...replace strict adherence
to snag the rotating accessory and cause loss of the wheel to damage the spindle, the flange (especially the installing...when working place is properly
supported. 27. USD201-2
Symbols... or
failure to these parts could burn your selected ...
Owners Manual - Page 6
...: • Before installing grinding wheel, always check that
a blotter part does not have any work on the tool.
1
1. For tool with the blotter that has larger diameter than 10N.m to stop . Loosen the wing bolts on both sides of
operator comfort during extended use the grinding wheel with support cover only (country specific)
1
1. After...
Owners Manual - Page 7
...Tighten the hex nut in the direction of wheel rotation to rotate after threading it through the eyelet on the top of the grinder is switched off. • Hold the tool firmly with one hand on the switch handle and the other hand on the front...the tool will only cause a poor finish and overloading of arrow as shown in the inner flange. Then install the wheel, outer flange and hex nut.
Owners Manual - Page 8
...deformation or cracks may break hooking part.
1 4
1. Hook A 3. Screwdriver
013743
To remove, lift it up dust or foreign matters. Rib A 4. NOTE: Dust cover attachments installed on the handles R/L with built... R
3. Dust cover
attachment L
3
013619
Dust cover attachment R/L are respectively installed on GS5000 and GS6000 do so causes damage to the tool or a personal injury. •...
Owners Manual - Page 9
Commutator 2. When this occurs, both carbon brushes should be performed by Makita Authorized Service Centers, always using Makita replacement parts. Brush holder cap
2. Screwdriver
1 2
013603
Use a screwdriver to the tool. If inspection shows the trouble is warranted to you . This Warranty does not apply where:
repairs have been made to remove the brush holder caps. Keep the ...
Flyer (English) - Page 1
makitatools.com 5" STRAIGHT GRINDER
PERFORMANCE
POWERFUL 7.0 AMP MOTOR DELIVERS MORE OUTPUT AND 5,600 RPM FOR ...Brushes for Easier Serviceability
5,600 RPM
Powerful 7.0 AMP motor delivers more output and 5,600 RPM
COMFORT
Rubberized gear housing and handle for operator
comfort and control
CONVENIENCE
"Tool-less" guard cap for quick wheel removal
SERVICEABILITY
Model GS5000
**shown with ...
Flyer (English) - Page 2
For a complete listing, please refer to stock on hand. All models and accessories subject to the Makita General Catalog or visit our website at makitatools.com or call 1-800-4MAKITA.
5" STRAIGHT GRINDER
Model GS5000
FEATURES & BENEFITS
n Powerful 7.0 AMP motor delivers more output and 5,600 RPM for demanding applications
n Rubberized handle and gear housing for increased operator comfort...
Makita GS5000 Reviews
Do you have an experience with the Makita GS5000 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Makita yet.
Earn 750 points for your review!