Makita 5008MGA Support and Manuals
Get Help and Manuals for this Makita item
This item is in your list!
View All Support Options Below
Free Makita 5008MGA manuals!
Problems with Makita 5008MGA?
Ask a Question
Free Makita 5008MGA manuals!
Problems with Makita 5008MGA?
Ask a Question
Popular Makita 5008MGA Manual Pages
Owners Manual - Page 2
...power tool. If devices are subject to lose control. ENGLISH
SPECIFICATIONS
Model
5008MG / 5008MGA
Blade diameter
210 mm (8-1/4")
at 50°
51.5 mm...dust. Keep cord away from heat, oil, sharp edges or moving parts. 15. Remove any way. SAVE THESE INSTRUCTIONS...the switch is an increased risk of dust extraction and collection facilities, ensure these devices can be ...
Owners Manual - Page 3
...or straight edge guide.
A typical ...qualified repair person using only identical replacement parts. ...support, workpiece support, and supply cord routing (if applicable).
000157
5. Do not reach underneath the workpiece. SERVICE 23. GEB013-1
SPECIFIC SAFETY RULES
DO NOT let comfort or familiarity with the power tool or these instructions and in your hands or across your saw...
Owners Manual - Page 4
...grip with both hands. Gum and wood pitch hardened on the saw . If blade adjustment shifts while cutting, it with the blade. Supports must be tight and secure before making a "plunge cut" into...the panel on both hands on blades slows saw to either side of the panel. Do not use gasoline. Unsharpened or improperly set blades produce narrow kerf causing excessive friction, blade...
Owners Manual - Page 5
... instantly. Raise the lower guard with the circular saw can lead to a complete stop after completing a cut is accidentally dropped, lower guard may operate sluggishly due to see that the blade cuts without decrease in its path. To check lower guard, open position. For all other part, in a vise. Check lower guard for...
Owners Manual - Page 6
...Do not use the tool. Wear a dust mask and hearing protection when use any...saw blade.
20. Take caution to follow the safety rules stated in this manual.
At this instruction manual... may be sure that the tool is equal to reduce potential for dangerous KICKBACKS which can cause personal injury. Setting bevel angle Loosen the lever and tentatively set...
Owners Manual - Page 7
... 2
007331
Hex wrench is unplugged. To install hex wrench, place it on the handle and...start even if the tool is plugged. Electric brake For model 5008MGA only This tool is switched off the lens of lamp....Release the switch trigger to stop blade after switch trigger release, have tool serviced at a Makita service center. CAUTION: • Always be sure that the switch trigger actuates properly...
Owners Manual - Page 8
...Set the base on new cut line, and start cut without the blade making any contact. If the cut by the blade. Realign tool on the workpiece to loosen the hex bolt counterclockwise. Attempt to avoid positioning which exposes operator to chips and wood dust being ejected from saw... to perform clean cutting operation, connect a Makita vacuum cleaner to install or remove the
blade. Then connect a ...
Owners Manual - Page 9
...to persons.
Screwdriver
1
2
007334
For model 5008MGA only After replacing brushes, plug in the tool and break in brushes by Makita Authorized or Factory Service Centers, always using a triangular rule, try square, etc.
1
2
1. Triangular rule 1
007333
Replacing carbon brushes
1. Replace when they wear down to slip in this manual. Use only identical carbon brushes. Take...
Owners Manual - Page 10
... Makita will repair (or at our option, replace) without charge. EN0006-1
10 MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, INCLUDING IMPLIED WARRANTIES OF "MERCHANTABILITY" AND "FITNESS FOR A SPECIFIC ...for the period of Makita's Factory or Authorized Service Centers. MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is caused by others: repairs are required because ...
Parts Breakdown - Page 2
... PIPE 9, 5007MG F. NUT M8-13, 5007MG F. WASHER 8, 5037NB ANGLER GUIDE, 5008MGA
Page 2 of 3
Quantity 1 1 1 1 1 1 1 1 1...Part...5008MGA TENSION SPRING 4, 5008MGA SPACER, 5007MG BEARING RETAINER 23-36, 5007MG BALL BEARING 6003DDW, LS1013 P.H. SPRING 9, LS1011 SHAFT LOCK, 5007MG CAP, 5007MG FLAT WASHER 15, LS1011N BALL BEARING 6002DDW,BO5001 URETHANE WASHER 26, 5007MG BLADE CASE SET, 5008MGA MAKITA...
Parts Breakdown - Page 3
...GUIDE RULE, 4200H HEX WRENCH 6, 3705, HR5000 8-1/4 SAW BLADE, 5008FA
5008MGA
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1
Page 3 of 3
8/18/2010 BOLT M8X90,5007MG HEX.SCREW M5X8, 4200N BASE CPL., 5008MGA...-8 783204-6 D-21521
Parts Breakdown
SHOULDER PIN 6-7, 5007MG N/A
SLEEVE 6, 5007MG F. BOLT M5X40, 5007MG F.S.N.BOLT M8X24, 5007MG PIPE 9, 5007MG DEPTH GUIDE, 5008MGA SHOULDER PIN 6-7, 5007MG...
Flyer (English) - Page 1
...CIRCULAR SAW
MAGNESIUM COMPONENTS CREATE A LIGHTWEIGHT SAW THAT IS WELL-BALANCED AND JOBSITE TOUGH
Large Cutting and Bevel Capacities with Positive Stops at 22.5° and 45° Reinforced Power Cord Withstands Jobsite Abuse Blade Wrench is Attached to Saw...depth guide allow user to measure and follow cuts accurately
CONVENIENCE
Model 5008MGA (Electric Brake)
Built-in LED lights and dust blower...
Flyer (English) - Page 2
... CIRCULAR SAW
Model 5008MGA
FEATURES & BENEFITS
■ Make quick, one-handed adjustments using large, rubberized levers ■ Large cutting and bevel capacities with positive stops at 22.5° and 45° ■ Reinforced power cord withstands jobsite abuse and lowers repair costs ■ Built-in dust blower enhances the line of Circular Saw accessories.
All specifications...
Makita 5008MGA Reviews
Do you have an experience with the Makita 5008MGA that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Makita yet.
Earn 750 points for your review!