Makita AN453 Support and Manuals
Get Help and Manuals for this Makita item
This item is in your list!
View All Support Options Below
Free Makita AN453 manuals!
Problems with Makita AN453?
Ask a Question
Free Makita AN453 manuals!
Problems with Makita AN453?
Ask a Question
Popular Makita AN453 Manual Pages
Owners Manual - Page 2
... Do not operate when under the influence of the tool, read this instruction manual carefully before using the tool.
2. There may differ from dust or ...operating controls is dangerous. Only those involved in the tool operating/safety instructions.
6. Operate the tool within prescribed limits. ENGLISH
SPECIFICATIONS
Model Air pressure
AN453 4.5 - 8.5 kgf/cm2G (65 - 120 PSIG)
Nail length
...
Owners Manual - Page 3
... performed. The use the tool with less fatigue by Makita Authorized or Factory Service Centers, always using Makita replacement parts. The nail may occur. 32. Do not point the ejection port at the same time.
Death or serious injury may be extremely dangerous. 26. SAVE THESE INSTRUCTIONS. You can become jammed if you nail while inching...
Owners Manual - Page 4
...004295
To insure maximum performance, install an air set is not used, oil the tool with pneumatic tool oil by placing 2 (two) or 3 (three) drops into the air fitting.
INSTALLATION
Selecting compressor
Compressor air output ... is higher. Thus, for tool. ・ Read and understand tool labels and manual. ・ Operators and others in the system whichever is required. Adjust the oiler...
Owners Manual - Page 5
...of nailing
1.
Projection
2
1
3
008391
1. Hook
1.
1. Adjusting the shingle guide
1. Hook
008392
The shingle guide is turned fully in the B direction, decrease the air pressure. ASSEMBLY
CAUTION: ... tool is turned in desired position. Generally speaking, the tool service life will become shallower as the adjuster is used with the...set to release the adjusting plate.
Owners Manual - Page 6
...Lift and turn the coil support plate so that the arrow with the coil support plate set properly in working order
before operation. 1. Coil support
1
plate
2. A hose coupling must be installed on the nailer.
Feed Claw
2
008397...the first nail in the driver channel and the second nail in such a way that the air socket locks firmly into position when installed onto the air fitting....
Owners Manual - Page 7
...with a hammer to drive out the nail jamming from the ejection port. Jammed nailer
1. When the nailer becomes jammed, do as kerosene, #2 fuel oil or diesel fuel. If the ... from the magazine before
attempting to re-contacct against the workpiece with all local and national code requirement.
7 Periodically clean the areas around the contact element will prevent smooth movement of recoil...
Owners Manual - Page 8
Maintenance of nailer Always check the ...to assure free movement of such liquids may result in the oiler of compressor, air set . After drying off the tool before operation. Drain cock
1
008402
With tool ...more frequent recleaning. Avoid exposure to assure good lubrication and operation or moving parts. Do not use gasoline or other similar highly volatile
liquids for cleaning. If...
Owners Manual - Page 9
... of any trouble develop during operation. This Warranty does not apply where:
repairs have been made to the hose.
It is caused by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
Hoses must also be performed by defective workmanship or material, Makita will repair (or at our option, replace) without charge. This Warranty gives you specific legal...
Parts Breakdown - Page 2
... AN453 O-RING 21, AN453 O-RING 45, AN453 HEAD VALVE, AN453 O-RING 42, AN453 O-RING 30, AN453 O-RING 35, AN453 DRIVER CPL., AN453 O-RING 45, AN453 O-RING 45, AN453 CYLINDER, AN453 CYLINDER SEPARATER, AN453 O-RING 67, AN453 CUSHION F, AN453 CAUTION LABEL, AN453 HOUSING CPL., AN453 FRONT HOUSING GUARD, AN453 O-RING 42, AN453 O-RING 5, AN453 DRIVER GUIDE CPL., AN453 SPRING WASHER 6, AN453 COVER, AN453...
Parts Breakdown - Page 3
...
1
87
HY00000153
PAN HEAD SCREW M4X10, AN453
1
88
HY00000161
SPRING WASHER 4, AN453
1
89
HY00000185
LEVER PLATE, AN453
1
90
HY00000184
LOCK PLATE, AN453
1
91
HY00000181
RING 9, AN453
1
92
HY00000075
H.S.H.BOLT M5X30, AF505
1
93
HY00000162
SPRING WASHER 5, AN453
1
94
HY00000186
SINGLE GUIDE, AN453
1
95
HY00000075
H.S.H.BOLT M5X30, AF505
1
96
HY00000162
SPRING...
Parts Breakdown - Page 4
1,001 1,002 1,003
195246-2 181434-7
783202-0
Parts Breakdown
N/A OIL SUPPLY 30CC, AF502
HEX WRENCH 4, JR3000V
AN453
1 1 1
Page 4 of 4
8/18/2010
Flyer (English) - Page 1
1-3/4" ROOFING COIL NAILER
EASY LOADING ADJUSTABLE CANISTER Built-in Magnet Ensures Last Nail is Driven to Prevent Lost Nails Large Carbide Inserts on...
Quick "tool-less" depth adjustments for more precise control and flush nailing
DURABILITY
Aluminum housing for longer tool life
SPEED
Model AN453
"Tool-less" shingle guide for Cleaning or Maintenance
POWER
Only 5.2 lbs. MORE POWER.
Flyer (English) - Page 2
...
I Hex wrench (783202-0) I Oil supply (181434-7) I Safety goggles (192517-8)
SPECIFICATIONS
Operating air pressure Nail size Magazine capacity Dimensions (LxWxH) Net weight Shipping weight UPC code
65 - 120 PSI 3/4" - 1-3/4"
120 10-3/8" x 4-5/8" x 10-5/8"
5.2 lbs. 6.5 lbs. 088381-090179
AN453
Makita offers a wide variety of NAILER accessories. for less weight, more power I Adjustable tool hook...
Makita AN453 Reviews
Do you have an experience with the Makita AN453 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Makita yet.
Earn 750 points for your review!