Makita 2705 Support and Manuals
Get Help and Manuals for this Makita item
Popular Makita 2705 Manual Pages
Owners Manual - Page 3
... or gases. 3. Poor installation may cause risk of the blade.
6. REPLACEMENT PARTS. If the plug does not fit fully in doubt, DO NOT PLUG IN THE APPLIANCE. If it can suffer serious personal injury. 1. Table 1: Minimum gage for recommended accessories. when changing accessories such as damage to install the proper outlet. Consult the owner's manual for cord
Ampere Rating...
Owners Manual - Page 4
.... Take caution to cut -off pieces near the blade or touch the blade guard while the blade is running .
22. SAVE THESE INSTRUCTIONS. INSTALLATION
Positioning table saw blade. Immediately raise the riving knife/spreader to guide along the fence.
18. NEVER make sure that could indicate poor installation or a poorly balanced blade. 15. NEVER reach for vibration or wobbling that...
Owners Manual - Page 5
... floor.
NOTE: • Use a shallow depth setting when cutting thin
materials in the bottom of cut . Handwheel
3
006155
006148
Locate the table saw .
The table saw stand should be secured to easily handle the size of the work bench or table saw stand using the holes provided in order to the table surface. No.10 wood screw 40 mm (1-1/2") min. Arrow...
Owners Manual - Page 7
... slip, the wrench may come off and
unplugged before installing or removing the blade. • Use only the Makita socket wrench provided to do so may result in overtightening or insufficient tightening of the hex bolt. Table saw blade and blade guard are pointing down at the back of Table Saw Blade Guarding System
1
2 4
008941
5 3
1.
If your hand could cause...
Owners Manual - Page 8
...table saw has returned to the next setting and it stops as shown in kickback and serious injury. The riving knife/spreader unit can be installed and made ready for the attachment of operation. This position would be made operational. the sharp blade...-through -cutting
operations and the guard assembly with a dado type blade. Before operating the tool be sure to check that ...
Owners Manual - Page 11
... travel. If the rip fence is parallel with the blade, secure the rip fence 2 - 3 mm (5/64" - 1/8" ) from the blade. Table saw blade
guard assembly
1
and side guard
storage
Fig.3
Item 1 demonstarates both measurements using the tooth marked with a crayon. Mark one of Blade Guards and Accessories
1. The Blade Guard Assembly and Side Guards can be lifted when storing...
Owners Manual - Page 14
... they will cause the blade to the rip fence. Before ripping, make sure the rear end of kickback and personal injury. The support should be sure that ...table. Before operating the table saw, check to feed using a round-shaped file to move or shift on the top of the pawls. 1. Ripping
CAUTION: • When ripping, remove the miter... titled "Installing and adjusting rip fence".
3.
Owners Manual - Page 15
... is provided with positive stops at 90°, 45°right and left miter angles for free setting. Screw for
2
positive stop
1. Non-through cut Turn off " portion of the table. CROSS CUTTING
2. Miter gauge
3
008740
Slide the miter gauge into the blade. Bring stock flush up against fence and feed gently forward into the thick...
Owners Manual - Page 16
... the brush holder caps. Use of the sub table (R) Replacing carbon brushes
1. Carefully clean the blade guard and moving parts and rotating parts from time to elevate the blade • Guide rails for dado head sets. Lubrication To keep the table saw in the holders. Screwdriver
006173
To maintain product SAFETY and RELIABILITY, repairs, any assistance for its stated purpose.
Both...
Owners Manual - Page 17
... the table against the miter gauge (with the rip fence and table as follows. 1. C clamps
2. WARNING: • Do not use featherboards. Install the dado head set , ...install the dadao head set according to
manufacturer's instructions. 5. Fast or abrupt feeds can result if the wood becomes stuck and you try to keep the workpiece in ordinary ripping.
4. Adjust fence and blade...
Owners Manual - Page 18
... Service Centers.
Table stand set • Sliding guide
MAKITA LIMITED ONE YEAR WARRANTY
Warranty Policy
Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to the instruction manual for table saw stand that is provided with the table saw stand as an optional accessory. • Steel & Carbide-tipped saw blades
Table/Miter saw blades
Combination...
Parts Breakdown - Page 8
...,5402A CARBON BRUSH SET CB-154, UC3530A
BRUSH HOLDER CAP, 5007MG P.H. SCREW M6X60, LS1030 T. Parts Breakdown
2705
Products with multiple versions are listed in subsiding order with the newest version on top not indented
Fig # 1 2 3 4 8 9 10 11 12 13 14 15 15 16 17 18 19 20 21 23 24 25 26 27 28...
Parts Breakdown - Page 13
1,003 1,004 1,005 1,006
781038-1 782024-5 783224-0 A-94948
Parts Breakdown
WRENCH 19, 2704
1
WRENCH 13-22, 2704
1
N/A
1
10 32T CARBIDE-TIPPED SAW BLADE, 2705
1
2705
Page 13 of 13
8/18/2010
Flyer (English) - Page 1
... ease of measurement from the blade
to the rip fence for cutting set ups
EFFICIENT
Riving knife/spreader adjusts to 3 different positions for through,
non-through and dado cuts
PRECISION
Precision machined table top remains flat and true for accurate cuts right
out of the box
PERFORMANCE
Models 2705 2705X1 (Includes Portable Table Saw Stand)
Right extension table allows for greater cutting...
Flyer (English) - Page 2
...UPC code
088381-09327-9
2705X1 10" 5/8"
3-5/8" 2-1/2" 4,800 15.0 24-5/8" x 22-1/4"
Yes 114.7 lbs. 156.2 lbs.
1 088381-60304-1
Model 2705
Model 2705X1
Heavy Duty Design
Upright Stand Support
OPTIONAL ACCESSORIES
Portable table saw stand
No
Net weight
61.7 lbs.
Models 2705/2705X1
10" CONTRACTOR TABLE SAW
FEATURES & BENEFITS
New guard design allows the operator to view the blade...
Makita 2705 Reviews
We have not received any reviews for Makita yet.