Makita XLT01 Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita XLT01 manuals!
Problems with Makita XLT01?
Ask a Question
Free Makita XLT01 manuals!
Problems with Makita XLT01?
Ask a Question
Popular Makita XLT01 Manual Pages
Instruction Manual - Page 2
... A wrench or a key left attached to a rotating part of research and development, the specifications herein are subject to our continuing program of the power ... personal injuries. 12. Damaged or entangled cords increase the risk of electric shock. ENGLISH (Original instructions)
SPECIFICATIONS
Model
XLT01
Capacities
Machine screw Bolt
4 mm (5/32") - 8 mm (5/16") 4 mm (5/32") - ...
Instruction Manual - Page 3
... tool in this instruction manual may make a ... tool serviced by...replacement parts. Maintain power tools. Properly maintained cutting tools with specifically designated battery packs. Use the power tool, accessories and tool bits etc. Use power tools only with sharp cutting edges are less likely to bind and are easier to be controlled with the charger specified by a qualified
repair...
Instruction Manual - Page 4
... cartridge. 3. Never recharge a fully charged battery cartridge. Overcharging shortens the battery service life. 3. USD302-1
Symbols
The followings show the symbols used for maintaining maximum ... battery cartridge cool down before
completely discharged. Before using battery cartridge, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using ...
Instruction Manual - Page 5
...)
1
1. If not, it is not being pulled. In this situation, remove and recharge the battery. Then pull the trigger switch again to extend battery life. Installing or removing battery cartridge
1
1. Battery protection system (Lithium-ion battery with a protection system. Release the switch trigger to the "OFF" position when released.
1. The tool...
Instruction Manual - Page 6
...angle head.
1. Screw
3.
Then tighten the hex bolt to the instructions above.
To remove, loosen the screw and then take it ,...in the direction of the tool. Hex bolt
1
2. Installing or removing driver bit To install the bit, pull the sleeve in 45-degree increments). .... To install the hook, insert it may damage the tool. • When not operating the tool, always set the reversing...
Instruction Manual - Page 8
... to persons. Driver bit or socket bit Failure to use gasoline, benzine, thinner, alcohol or the like. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be included in the tool
package as standard accessories. The fastening torque is affected by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
8
They...
Instruction Manual - Page 9
... the above limitation or exclusion may also have been made or attempted by defective workmanship or material, Makita will repair (or at our option, replace) without charge. EN0006-1
9 If inspection shows the trouble is caused by others: repairs are required because of incidental or consequential damages, so the above limitation may not apply to you...
Makita DC18RC Instruction Manual - Page 3
...a risk of time. 6. This manual contains important safety and operating instructions for a long period of electric ... charge only MAKITA rechargeable batteries marked on , tripped over, or otherwise subjected to which is located so that it in order. 4. ENGLISH
Specifications
Model Input Output Weight...Makita authorized
service center to replace it will change from charger and unplug the ...
Makita DC18RC Instruction Manual - Page 4
...
full charge until after the cooling fan installed in a location exposed to prevent fast ... long time in the charger cools the battery cartridge. Trouble on the charger.
• Yellow light will begin after...be sometime clogged with cooling fan for charging Makita-battery cartridge. Recharge of battery with dust... optimal charging selected according to repair or maintenance, if the yellow...
XLT01Z Parts Breakdown - Page 2
Model XLT01Z Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part#
Description
001
187889-4 HOUSING SET
001 C10 263005-3 RUBBER PIN 6
001 C20 803B00-9 CAUTION LABEL
001 C21 802J50-9 CAUTION LABEL
001 D10
INC. 40
002
265995-6 TAPPING SCREW 4X18
003
815M17-6 XLT01...29
039
216002-8 STEEL BALL 4.8
040
187889-4 HOUSING SET
040 C10 263005-3 RUBBER PIN 6
040 C20 803B00...
Makita XLT01 Reviews
We have not received any reviews for Makita yet.