MSI IMGM45D Support and Manuals
Get Help and Manuals for this MSI item
Popular MSI IMGM45D Manual Pages
User Guide - Page 2
...
Revision History First release
Date September 2008
Technical Support
If a problem arises with your place of purchase or local distributor... solution can be obtained from the user's manual, please contact your system and no guarantee ... following help resources for FAQ, technical guide, BIOS updates, driver updates, and other countries. func=service for further guidance. We take every ...
User Guide - Page 3
... equivalent type recommended by service
personnel: The power cord or plug is incorrectly replaced. Always read the safety instructions carefully. 2.
Make sure the voltage of explosion if battery is damaged. All cautions and warnings on card or module. 9.
DO NOT COVER THE OPENINGS. 6. Always Unplug the Power Cord before setting it up. 5. CAUTION: Danger...
User Guide - Page 8
...Instructions ...iii FCC-B Radio Frequency Interference Statement iv W EEE (Waste Electrical and Electronic Equipment) Statement v Chapter 1 Product Overview 1-1
Mainboard Specifications 1-2 Block Diagram ...1-4 Mainboard Layout 1-5 Board Dimension 1-6 Back Panel & I/O Shield Drawing 1-7 Power Consumption 1-8 Safety Compliance & MTBF 1-9 Chapter 2 Hardware Setup 2-1 Quick Components Guide...
User Guide - Page 21
...Setup
Memory
The DIMM slots are intended for system memory modules. Manually check if the DIMM has been locked in the SO-DIMM slot. 3. Locate the SO-DIMM slots on the slot. Important
1. DDR2 SO-DIMM Slot
200-pin, 1.8V
Installing... clips at the sides. Make sure that you install the memory modules first before installing the CPU and cooler set.
2. Always insert the memory module into
the SO...
User Guide - Page 25
...capable of the cable is properly connected to your monitor manual for more information.)
USB Port The USB (Universal ...communications port that the other end of transmitting uncompressed streams. HDMI supports all TV format, including standard, enhanced, or high-definition video...connector is provided for a PS/2® mouse/keyboard. Hardware Setup
Back Panel
RS-232/422/485 M ou se Serial ...
User Guide - Page 27
Hardware Setup
Connector
IDE Connector: IDE1
This connector supports IDE hard disk drives, optical disk drives and other IDE devices. Refer to master / slave mode by the vendors for jumper setting instructions.
2-9 IDE1
Important
If you install two IDE devices on the same cable, you must configure the drives separately to IDE device's documentation supplied by setting jumpers.
User Guide - Page 35
..., TV tuner, and Robson NAND Flash. The PCI Express x 1 slot supports up to configure any necessary hardware or software settings for the expansion card to 250 MB/s transfer rate.
Hardware Setup
Slot
PCI (Peripheral Component Interconnect) Express Slot
The PCI Express slot supports PCI Express interface expansion cards. The CON1 is Master. Meanwhile, read...
User Guide - Page 43
...value to 03h when queried, even if the processor supports a higher CPUID input value. With virtualization, one computer...CPUID Value Limit BIOS feature allows you to circumvent problems with their own L1 Code & Data caches, Local APICs & thermal controls...Setup
Hardware Prefetcher The processor has a hardware prefetcher that automatically analyzes its requirements and prefetches data and instructions...
User Guide - Page 44
Configure SATA#1 as This setting specifies the function of PIO (Programmed Input/
Output)
3-8
The hard disk will not work
properly if you can use [Manual] to
define your own drive type manually.
[LBA/Large Mode]
Enabling LBA causes Logical Block Ad- Note that the
specifications of SATA ports.
Primary/Secondary/Third/Fourth IDE Master, Fifth...
User Guide - Page 45
...Serial Port 1/3/4/5/6 Address/IRQ Select an address and a corresponding interrupt for the hard disks. BIOS Setup
[DMA Mode] [S.M.A.R.T.]
[32 Bit Data Transfer]
Indicates the type of the serial port on... disk becomes offline.
This gives you to predict hard disk failure. COM Port Control This setting specifies the operation mode of Ultra DMA This allows you an opportunity to move data from ...
User Guide - Page 46
... tolerance value here for the specific range for the "CPUFAN1/SYSFAN1/SYSFAN2 TargetSpeed Value" items. If the current fan 3-10 MS-9818 Mainboard
Hardware Health Configuration These items display the current status of the CPU/system fan to prevent your system from overheating. CPUFAN1 Mode Setting, SYSFAN1 Mode Setting This item enables or...
User Guide - Page 47
...specific range for the "CPUFAN1/SYSFAN1 TargetTemp Value" items. If the current temperatures of the 3 fans reach to the maximum threshold (the temperatures set in the "CPUFAN1/ SYSFAN1 TargetSpeed Value" plus the tolerance values you set...3-11 BIOS Setup
speeds reach the maximum threshold (the fan speed set in the "CPUFAN1/SYSFAN1 TargetTemp Value" plus the tolerance values you set here), the ...
User Guide - Page 50
...or write to update the BIOS online first. Only FSB1066MHz CPU supports Intel AMT function. 3-14 The platform can also be configured to read from a remote source and this setting to a remote ...=service
2.
Unconfigure AM T/ME To finish the unconfiguration of AMT, set this capability is a protocol defined for remotely managing and securing PCs out-of AMT/ME settings and all the passwords ...
User Guide - Page 53
... archive. Clearing the TPM W hen the TPM is a task that local administrators can perform during the setup or re-configuration of the TPM Management console named Command Management.
Trusted Computing
BIOS Setup
TCG/TPM Support This setting controls the Trusted Platform Module (TPM) designed by the Trusted Computing Group (TCG). To block or allow...
User Guide - Page 56
...not be able to gain access to "capture" Interrupt 19. PS/2 M ouse Support Select [Enabled] if you to press any bootable disks attached to boot operating systems...set to [Enabled] and the boot sequence encounters an error, it is powered on . If disabled, the system continues to [On] will display the normal POST messages, instead of delay to press F1. When it asks you want to run setup...
MSI IMGM45D Reviews
We have not received any reviews for MSI yet.