Installation Manual
Page 9
Contents 11 Check the contents 12 Overview 12 Front controls 13 Rear connections 14 Card reader 16 Installation 16 Mounting location 17 Quick release bracket mounting 19 Panel mount 22 Mounting the transducer 22 Research 22 Select a transducer location 24 Attaching the transducer 25 Adjusting the transducer 26 Wiring 26 Guidelines 27 Power connection 27 Transducer... Device list 34 Diagnostics 36 Damping 36 Sonar setup 38 StructureScan 38 Autopilot setup 38 Fuel setup 41 Wireless setup 44 Bluetooth wireless technology Contents | ELITE Ti Installation Manual 9
Contents 11 Check the contents 12 Overview 12 Front controls 13 Rear connections 14 Card reader 16 Installation 16 Mounting location 17 Quick release bracket mounting 19 Panel mount 22 Mounting the transducer 22 Research 22 Select a transducer location 24 Attaching the transducer 25 Adjusting the transducer 26 Wiring 26 Guidelines 27 Power connection 27 Transducer... Device list 34 Diagnostics 36 Damping 36 Sonar setup 38 StructureScan 38 Autopilot setup 38 Fuel setup 41 Wireless setup 44 Bluetooth wireless technology Contents | ELITE Ti Installation Manual 9
Installation Manual
Page 11
Included only with units that do not include transducers. 5 Fuse holder (ATC blade) 6 Quick release mounting bracket 7 Fuse (3 amp) 8 Quick release mounting bracket screws (4 x #10 x 3/4 PN HD SS screws) 9 Bracket locking bolt and knob. (ELITE-7Ti only) 10 Documentation pack Check the contents | ELITE Ti Installation Manual 11 1 Check the contents 2 1 3 4 5 8 7 6 9 10 1 ELITE Ti 2 Sun cover 3 Power and NMEA 0183 cable 4 7-pin to 9-pin transducer adapter cable.
Included only with units that do not include transducers. 5 Fuse holder (ATC blade) 6 Quick release mounting bracket 7 Fuse (3 amp) 8 Quick release mounting bracket screws (4 x #10 x 3/4 PN HD SS screws) 9 Bracket locking bolt and knob. (ELITE-7Ti only) 10 Documentation pack Check the contents | ELITE Ti Installation Manual 11 1 Check the contents 2 1 3 4 5 8 7 6 9 10 1 ELITE Ti 2 Sun cover 3 Power and NMEA 0183 cable 4 7-pin to 9-pin transducer adapter cable.
Installation Manual
Page 12
... supports charts from Navico including Insight Genesis. The unit may be mounted to sensor data. 2 12 Overview The unit has a built-in (combined press = MOB) Overview | ELITE Ti Installation Manual The ELITE-5Ti and ELITE-7Ti can network over NMEA 2000, this allows access to the vessel with the supplied mounting bracket, or panel mounted on the dash.
... supports charts from Navico including Insight Genesis. The unit may be mounted to sensor data. 2 12 Overview The unit has a built-in (combined press = MOB) Overview | ELITE Ti Installation Manual The ELITE-5Ti and ELITE-7Ti can network over NMEA 2000, this allows access to the vessel with the supplied mounting bracket, or panel mounted on the dash.
Installation Manual
Page 17
... steel fasteners. 3. Installation | ELITE Ti Installation Manual 17 The dust from many materials commonly used . If the material is used in boat construction may exceed safe noise levels, and can cast off dangerous projectiles. For example, ear muffs, protective glasses, gloves and a dust mask. Screw down the bracket. 4. Quick release bracket mounting 1. Snap the unit...
... steel fasteners. 3. Installation | ELITE Ti Installation Manual 17 The dust from many materials commonly used . If the material is used in boat construction may exceed safe noise levels, and can cast off dangerous projectiles. For example, ear muffs, protective glasses, gloves and a dust mask. Screw down the bracket. 4. Quick release bracket mounting 1. Snap the unit...
Installation Manual
Page 19
Installation | ELITE Ti Installation Manual 19 Check that it is correctly aligned to the Mounting Template. 4. Drill all marked pilot holes. For recommended pilot hole size, refer to a vertical or horizontal reference. Using an appropriate saw, cut through the template and mounting surface, along the dotted ... the shaded center of each corner clip. Removing the unit from the quick release bracket Pull and hold the release handle and then pull the unit from the bracket. Check the Mounting Template for scaling accuracy, using a tape measure or ruler against the ruler printed ...
Installation | ELITE Ti Installation Manual 19 Check that it is correctly aligned to the Mounting Template. 4. Drill all marked pilot holes. For recommended pilot hole size, refer to a vertical or horizontal reference. Using an appropriate saw, cut through the template and mounting surface, along the dotted ... the shaded center of each corner clip. Removing the unit from the quick release bracket Pull and hold the release handle and then pull the unit from the bracket. Check the Mounting Template for scaling accuracy, using a tape measure or ruler against the ruler printed ...
Installation Manual
Page 24
... holes to suit fasteners. Ú Note: Check that may be installed parallel with bracket up to the transom of each outline, to allow for transducer height adjustment. Attach transducer to pass the plug through. 24 Mounting the transducer | ELITE Ti Installation Manual Mark drilling points in the middle of the boat and trace the... (deadrise). Ú Note: Ensure the entire bottom surface of the transducer hangs at least 3 mm (1/8th of an inch) lower than the bottom of the mounting surface that there is nothing on the 50/200 KHz transducer).
... holes to suit fasteners. Ú Note: Check that may be installed parallel with bracket up to the transom of each outline, to allow for transducer height adjustment. Attach transducer to pass the plug through. 24 Mounting the transducer | ELITE Ti Installation Manual Mark drilling points in the middle of the boat and trace the... (deadrise). Ú Note: Ensure the entire bottom surface of the transducer hangs at least 3 mm (1/8th of an inch) lower than the bottom of the mounting surface that there is nothing on the 50/200 KHz transducer).
Installation Manual
Page 50
...list is available at: lowrance.com NMEA 2000 NMEA 2000 networking is only available with built-in compass 000-10613-001 RC42 Rate compass ELITE Ti accessories Part number 000-10027-001 000-0127-49 000-12750-001 000-12749-001 Description Quick release mounting bracket kit Power and NMEA ...0183 Cable Sun cover for the ELITE-5Ti Sun cover for the ELITE-7Ti Accessories | ELITE Ti Installation Manual
...list is available at: lowrance.com NMEA 2000 NMEA 2000 networking is only available with built-in compass 000-10613-001 RC42 Rate compass ELITE Ti accessories Part number 000-10027-001 000-0127-49 000-12750-001 000-12749-001 Description Quick release mounting bracket kit Power and NMEA ...0183 Cable Sun cover for the ELITE-5Ti Sun cover for the ELITE-7Ti Accessories | ELITE Ti Installation Manual