Sonar and DSI Installation Manual
Page 1
...the installation of this installation does not apply to the GPS only units since they do not have a transducer. Turn to pages 8-11 for information on the bracket mount. not included) Drill Marine grade above-or-below waterline sealant 1" (25mm) or 5/8" (15mm) ... INSTALL_SONAR_DSI.indd 1 9/14/2011 11:55:30 PM Traditional Sonar Transducer Installation One piece bracket (Recommended Tools and Supplies - Traditional Sonar and DSI Sonar Installation This document covers the installation of the transducer and display unit installation, which includes connecting the unit to power and...
...the installation of this installation does not apply to the GPS only units since they do not have a transducer. Turn to pages 8-11 for information on the bracket mount. not included) Drill Marine grade above-or-below waterline sealant 1" (25mm) or 5/8" (15mm) ... INSTALL_SONAR_DSI.indd 1 9/14/2011 11:55:30 PM Traditional Sonar Transducer Installation One piece bracket (Recommended Tools and Supplies - Traditional Sonar and DSI Sonar Installation This document covers the installation of the transducer and display unit installation, which includes connecting the unit to power and...
Sonar and DSI Installation Manual
Page 2
... ratchets to the ground. 1. Insert the ratchets in a smooth flow of the transducer bracket. 2 Good locations Too high Poor angle Poor locations 2. Slide the transducer into the bracket and temporarily slide the bolt through the transducer bracket. B. Select a transducer location To function properly the Skimmer transducer must be in the water at least one foot away from the...
... ratchets to the ground. 1. Insert the ratchets in a smooth flow of the transducer bracket. 2 Good locations Too high Poor angle Poor locations 2. Slide the transducer into the bracket and temporarily slide the bolt through the transducer bracket. B. Select a transducer location To function properly the Skimmer transducer must be in the water at least one foot away from the...
Sonar and DSI Installation Manual
Page 3
...INSTALL_SONAR_DSI.indd 3 9/14/2011 11:55:31 PM Reinsert the ratchets into the bracket, this process until the transducer can not be adjusted so its face is parallel to see if the transducer will adjust so its face is parallel with the ground. Repeat this time with... with the ground. Look at dot the transducer from the bracket. Traditional Sonar 3. Hold the transducer Align dot and assembly against the transom. 5. Check to the ground, remove the transducer and ratchets from A the side. Reassemble the transducer and bracket and place it is parallel with the dot...
...INSTALL_SONAR_DSI.indd 3 9/14/2011 11:55:31 PM Reinsert the ratchets into the bracket, this process until the transducer can not be adjusted so its face is parallel to see if the transducer will adjust so its face is parallel with the ground. Repeat this time with... with the ground. Look at dot the transducer from the bracket. Traditional Sonar 3. Hold the transducer Align dot and assembly against the transom. 5. Check to the ground, remove the transducer and ratchets from A the side. Reassemble the transducer and bracket and place it is parallel with the dot...
Sonar and DSI Installation Manual
Page 4
... depend on the connector on the hull. 3. Drill the mounting holes for the #10 screws). Traditional Sonar D. Attaching Transducer to pass the connector through the bracket. otherwise transducer may not kick- Use a #29 bit (for the transducer bracket. When the transducer and bracket are properly aligned mark its face is parallel with the ground Bottom of the...
... depend on the connector on the hull. 3. Drill the mounting holes for the #10 screws). Traditional Sonar D. Attaching Transducer to pass the connector through the bracket. otherwise transducer may not kick- Use a #29 bit (for the transducer bracket. When the transducer and bracket are properly aligned mark its face is parallel with the ground Bottom of the...
Sonar and DSI Installation Manual
Page 5
...could damage hull integrity. In a shoot-thru-hull installation the transducer is epoxied to the hull, make sure the area is facing the bow (front) of the boat. If the transducer has a built in the transducer mounting bracket to confirm hull specifications. Contact the boat dealer or manufacturer ...Before you epoxy the transducer to the inside of the boat hull. Hull Keel pad keel pad that offers ...
...could damage hull integrity. In a shoot-thru-hull installation the transducer is epoxied to the hull, make sure the area is facing the bow (front) of the boat. If the transducer has a built in the transducer mounting bracket to confirm hull specifications. Contact the boat dealer or manufacturer ...Before you epoxy the transducer to the inside of the boat hull. Hull Keel pad keel pad that offers ...
Sonar and DSI Installation Manual
Page 7
.... 51-45) is an optional accessory and is curved to a trolling motor. The Pod transducer does not need a TMB-S mounting bracket. Installing transducer on trolling motor: 1. Attach the skimmer transducer to the bracket as shown in the water. 7 0.TWEETY INSTALL_SONAR_DSI.indd 7 9/14/2011 11:55:32 ... It only needs a hose clamp (adjustable strap). Internal tooth washer Bolt Plastic bracket Lock nut Flat washer 2. S lide the adjustable strap (hose clamp) through the plastic bracket on the skimmer transducer or through LEI Extras at www.lei-extras.com. Traditional Sonar 6. When ...
.... 51-45) is an optional accessory and is curved to a trolling motor. The Pod transducer does not need a TMB-S mounting bracket. Installing transducer on trolling motor: 1. Attach the skimmer transducer to the bracket as shown in the water. 7 0.TWEETY INSTALL_SONAR_DSI.indd 7 9/14/2011 11:55:32 ... It only needs a hose clamp (adjustable strap). Internal tooth washer Bolt Plastic bracket Lock nut Flat washer 2. S lide the adjustable strap (hose clamp) through the plastic bracket on the skimmer transducer or through LEI Extras at www.lei-extras.com. Traditional Sonar 6. When ...
Sonar and DSI Installation Manual
Page 15
... E diminish product performance. B If it is installed parallel to ensure the transducer is not placed in a smooth flow of the transducer bracket. 2. Slide the transducer into the bracket and temporarily slide the bolt through the transducer bracket. DSI Sonar Good location Poor angle Poor location Too high Aligning transducer ratchets Ratchets are used to the ground. 1. Insert the ratchets...
... E diminish product performance. B If it is installed parallel to ensure the transducer is not placed in a smooth flow of the transducer bracket. 2. Slide the transducer into the bracket and temporarily slide the bolt through the transducer bracket. DSI Sonar Good location Poor angle Poor location Too high Aligning transducer ratchets Ratchets are used to the ground. 1. Insert the ratchets...
Sonar and DSI Installation Manual
Page 16
... face is parallel with the ground and its center is parallel with the ground. 2. Hold the transducer and bracket assembly against the transom. Mounting to the ground, remove the transducer and ratchets from the side. DSI Sonar 3. Hold the transducer assembly against the transom. 5. Repeat this time with the letter "B" aligned with the dot stamped...
... face is parallel with the ground and its center is parallel with the ground. 2. Hold the transducer and bracket assembly against the transom. Mounting to the ground, remove the transducer and ratchets from the side. DSI Sonar 3. Hold the transducer assembly against the transom. 5. Repeat this time with the letter "B" aligned with the dot stamped...
Sonar and DSI Installation Manual
Page 17
Use a #29 bit (for the #10 screws). 4. Attach the transducer to the hull for the transducer bracket. DSI Sonar Shoot-thru hull The DSI transducer can install the DSI transducer on trolling motor Using a flathead screwdriver, depress the release tab and slide off the transducer mount. The optional DSI trolling motor accessory (pn: 00010261-001) is not a recommended installation method since...
Use a #29 bit (for the #10 screws). 4. Attach the transducer to the hull for the transducer bracket. DSI Sonar Shoot-thru hull The DSI transducer can install the DSI transducer on trolling motor Using a flathead screwdriver, depress the release tab and slide off the transducer mount. The optional DSI trolling motor accessory (pn: 00010261-001) is not a recommended installation method since...
Operation Manual
Page 43
... Size Display Backlight Communications Shared devices supported Transmit Power Power Requirement Voltage Input Current drain Fuse type Elite 5 DSI General 5.4" H (134mm) x 6.8" W (174mm); 6" H (152mm) with bracket (5" diagonal) Enhanced Solar MAX™ 480x480 256 color TFT LCD Cold cathode fluorescent lamp (10...630mA) 3-amp Automotive (not supplied) Specifications Max depth Transducer Frequency Max speed Transducer DSI Sonar 250 ft (76m) 455/800kHz 50 mph (80 kph) 2-8 mph (3-12 kph) optimal for imaging DSI (Downscan) transducer Transducer cable 20ft (6m) GPS Mapping card slot microSD (...
... Size Display Backlight Communications Shared devices supported Transmit Power Power Requirement Voltage Input Current drain Fuse type Elite 5 DSI General 5.4" H (134mm) x 6.8" W (174mm); 6" H (152mm) with bracket (5" diagonal) Enhanced Solar MAX™ 480x480 256 color TFT LCD Cold cathode fluorescent lamp (10...630mA) 3-amp Automotive (not supplied) Specifications Max depth Transducer Frequency Max speed Transducer DSI Sonar 250 ft (76m) 455/800kHz 50 mph (80 kph) 2-8 mph (3-12 kph) optimal for imaging DSI (Downscan) transducer Transducer cable 20ft (6m) GPS Mapping card slot microSD (...
Operation Manual
Page 44
...) with bracket Elite 4: (3.5" diagonal) 320x240 (256 color) TFT LCD Mark 4: (3.5" diagonal) 320x240 monochrome TFT LCD White LED (10 levels) NMEA 0183 Output VHF and Autopilot through NMEA 0183 Power 2800W PTP; 350W RMS 12V 10 to 17V at 13.5V (250mA) 3-amp Automotive (not supplied) Max depth Transducer Frequency Max speed Transducer DSI Sonar 200...
...) with bracket Elite 4: (3.5" diagonal) 320x240 (256 color) TFT LCD Mark 4: (3.5" diagonal) 320x240 monochrome TFT LCD White LED (10 levels) NMEA 0183 Output VHF and Autopilot through NMEA 0183 Power 2800W PTP; 350W RMS 12V 10 to 17V at 13.5V (250mA) 3-amp Automotive (not supplied) Max depth Transducer Frequency Max speed Transducer DSI Sonar 200...