LiftMaster Readers Support and Manuals
Get Help and Manuals for this LiftMaster item
View All Support Options Below
Free LiftMaster Readers manuals!
Problems with LiftMaster Readers?
Ask a Question
Free LiftMaster Readers manuals!
Problems with LiftMaster Readers?
Ask a Question
Popular LiftMaster Readers Manual Pages
User Guide - Page 1
... READER
MODEL KPR2000
TABLE OF CONTENTS
INTRODUCTION 2
FEATURES 2 ACCESSORIES 2 CARTON INVENTORY 2 SPECIFICATIONS 2 ONE YEAR LIMITED WARRANTY 2
INSTALLATION 3
INSTALL THE KPR2000 3 CHOOSE AN OPERATION MODE 3
WIRING 4
WIRE THE KPR2000 4
PROGRAMMING 5
CONFIGURE THE KPR2000 5 PROGRAM CARDS AND PINS 6
ADVANCED PROGRAMMING 7
PANIC CODES 7 ALARM 8 SOUND & LIGHT INDICATION 8 RESET...
User Guide - Page 2
...Access Pedestal • Model PEDAD 4 x 4 Pedestal Adaptor • Model PS12V2A 12 Vdc, 2 Amp Power Supply
Carton Inventory
NOT SHOWN: User's Manual
Diode IN4007 (For Relay circuit protection)
Manager Add Card Self Tapping Screws #8 x 1"
Wall Anchors #6 x 1 1/8" Manager Delete Card
KPR2000 Keypad/Proximity Reader/Controller
Security Screwdriver (T-10 Security Torx Driver)
Specifications...
User Guide - Page 3
... configuration for pass-through operation. IMPORTANT NOTE: Both modes of operation support Auto User ID generation (simplest method) and manual entry of Wiegand data.
• Card + PIN: The User must first present a valid Wiegand Card to the KPR2000 and then enter their PIN code followed by the # key, in order to be granted access.
•...
User Guide - Page 4
... (Normally Closed)
WIRING EXAMPLES:
Gate/Door Operator or Fail-Secure Strike
Magnetic Lock or Fail-Safe Strike
Normally Open
Install a 1N4007 or equivalent diode. KPR2000
Common
Orange Purple
Red Gray
Pink
(1 Amp Maximum)
Black
External Alarm
Normally Open
Install a 1N4007 or equivalent diode.
Wire Insulation Color
Wiring Function Basic Stand Alone Wiring
Notes...
User Guide - Page 5
...
SET STRIKE-OUT ALARM
The strike-out alarm will engage after entering a valid master code or card. Programming Step 1. Update Master Code 3. Enter Program Mode
2. Card or PIN
3. Default is OFF. Factory default is HID 26 bit. Enter Program Mode 2. Exit Program Mode
Keystroke Combination ✱ (Master Code) # 6 0 #
6 1 # (Alarm sounds for 10 minutes
7 2 # Enter Master Code or Valid Card...
User Guide - Page 6
... vary depending on the access configuration. PINs greater than 1000 must be any 4~8 digits between 0000~99999999 (except 1234 which is reserved for programming specific Card Numbers: Facility Code + ID Number (including leading 0's) Example: FAC- 24, ID- 100 would be proceeded with leading zeros.
Exit Program Mode
✱
CHANGE A PIN
This operation is...
User Guide - Page 7
... Step 1. Duplicated Codes act as a normal User Code. PROGRAMMING
ACCESS CONFIGURATION: CARD ONLY
USING MANAGER CARDS
KPR2000 managers can use a User ID of 2001~2010 ONLY. • Panic Codes must be used in "Card Only" configuration. This is a form of Auto User ID enrollment and is a section of the KPR2000 memory set aside specifically for cards and PINs to...
User Guide - Page 8
... Short Single Beep
01-36716B
FOR TECHNICAL SUPPORT DIAL OUR TOLL FREE NUMBER: 1-800-528-2806
©...button while power is powered, the alarm will also require reprogramming of the Master Add and Delete Cards. ADVANCED PROGRAMMING
Alarm
TO RESET THE ALARM
Programming Step
Keystroke Combination
To reset the door forced open warning
(Read valid card) OR (Master Code #)
To reset...
LiftMaster Readers Reviews
We have not received any reviews for LiftMaster yet.