LiftMaster MEGA SLIDE-X Support and Manuals
Get Help and Manuals for this LiftMaster item
View All Support Options Below
Free LiftMaster MEGA SLIDE-X manuals!
Problems with LiftMaster MEGA SLIDE-X?
Ask a Question
Free LiftMaster MEGA SLIDE-X manuals!
Problems with LiftMaster MEGA SLIDE-X?
Ask a Question
Popular LiftMaster MEGA SLIDE-X Manual Pages
MEGA SLIDE-X MSLXDCBB Manual - Page 1
Radio Receiver Included
The Chamberlain Group, Inc. 845 Larch Avenue Elmhurst, Illinois 60126-1196
www.liftmaster.com
Model MSLXDCBB3 (MEGA SLIDE X)
1/2 HP COMMERCIAL DUTY SLIDE GATE OPERATOR
OWNER'S MANUAL
THIS UNIT IS A CLASS 1, 2, 3, OR 4 SLIDE GATE OPERATOR FOR USE IN SLIDE GATE APPLICATIONS
MEGA SLIDE-X MSLXDCBB Manual - Page 2
... Reverse Device (IRD 14
RECEIVER
Set Security Mode 15 Programming the Remote to the Receiver 15 To Erase All Remote Control Codes 15
OPERATION AND MAINTENANCE
General Service 16 Battery Disposal 16 Battery Replacement 16 Battery Maintenance/Testing 16 Battery Handling/Storage 16
TROUBLESHOOTING
AVERTISSEMENT Battery Checkout 17 Gate Not Operating 17
ATTENTION SUGGESTED LOOP SENSOR...
MEGA SLIDE-X MSLXDCBB Manual - Page 3
... of the gate operator frame towards the chain. MaFlnipuaswl Ritcehledaoswen to Podsisiteionngage power to be manually opened. INTRODUCTION
CARTON INVENTORY
Before beginning your installation check that all components were provided and received undamaged.
This will remove power to the motor allowing the gate to
motor and for factory provided parts. To operate the gate manually, place...
MEGA SLIDE-X MSLXDCBB Manual - Page 4
... or building such as a factory or loading dock area or other building servicing the general public. SAFETY ACCESSORY SELECTION
All UL325 compliant LiftMaster gate operators will accept external entrapment protection devices to protect people from motorized gate systems. UL325 requires that the installation must have warning signs placed in audio alarm.
Contact sensors such as...
MEGA SLIDE-X MSLXDCBB Manual - Page 5
...intended for entrapment protection functions shall be located at any moving part of the vehicular gate.
6. All exposed pinch points are not obstructed or impeded by a moving .
b. A gate operator can create risks for each individual application. Install the gate operator only when:
a. The gate must take into every design. Outdoor or easily accessible controls shall...
MEGA SLIDE-X MSLXDCBB Manual - Page 6
...
(use all gates and operators be installed to conform to
replace beams marked NOTE-1 NOTE-3: Reversing edge or beam will re-open .
It is recommended that all safety devices that is an "A1" inherent entrapment sensing system with an audio alarm (reverses gate direction). NOTE: This unit to be installed according to their manufacturer's instructions and are...
MEGA SLIDE-X MSLXDCBB Manual - Page 7
... people get their hands or feet caught
CAUTION between the moving parts of the
gate.
They cannot retract their hands and arms through openings anywhere the gate may move at least 6' (1.8 m) from a moving gate:
CAUTION • Install Warning signs on EACH side of a vehicular horizontal slide gate. To prevent entrapment injuries, mount controls
ATTENTION at any point...
MEGA SLIDE-X MSLXDCBB Manual - Page 8
OPERATOR OVERVIEW
The LiftMaster model MEGA SLIDE X slide gate operator is sensed. • Upon complete system failure (lightning, surges, etc.) gate can be pushed open by UL are many parts that make it the front runner in the industry. Setting the MEGA SLIDE X apart are UL-325, UL-991)
8 Maximum length of 30'. (Free moving operation) • 10 year perforation warranty on cover and ...
MEGA SLIDE-X MSLXDCBB Manual - Page 11
.... This input operates as 1, 2, 3 above listed functions. NOTE: J5 inputs 1-8 are the commons (0 Vdc) used for connection to activate the following inputs. Acts same as a hold gate open position if it ). Input Commands - J5 Connector Block at top of sight, intended manual reset input. This function will also reset unit. For your Mega Slide X, please...
MEGA SLIDE-X MSLXDCBB Manual - Page 13
If batteries are low, gate will stay open after the loss of feet, minus one foot, for the closing timer delay. SWITCH PACK S2 (1-5)
On the MEGA SLIDE X the switches 1-5 on , use S2 1-5 to set the dip switches to add up to the number of power. SWITCH PACK S2 (6-8)
SWITCH 6: Sets auxiliary open --pulse close timer...
MEGA SLIDE-X MSLXDCBB Manual - Page 14
... the open and closed limit. Remember to set to adjust limit nuts, the detent plate must be adjusted by qualified service personnel.
The gate should be redefined. If during the setup, a double entrapment condition occurs, refer to the troubleshooting section to assist in small, 1 hour increments until the gate travels the full distance.
Spinning it will...
MEGA SLIDE-X MSLXDCBB Manual - Page 16
...replacement. LiftMaster does
AVERTISSEMENT not recommend storage of batteries in pairs. BATTERY REPLACEMENT
AVERTISSEMENT Service Kits are available for manually initiating the battery test. Please contact
Technical Support...Refer to insure proper and safe operation, it is conducted automatically. CAUTION • Charge voltage for wear and lubricate. Replace in the field. WARNING
To ...
MEGA SLIDE-X MSLXDCBB Manual - Page 18
... lane (Figure 3). Card Reader Tele-entry Radio Control
Safety Loop
Safety Loop
Mega Slide X
Safety Loop
Open Loop
Mega Slide X
18 Mega Slide X
DUAL DIRECTION AS ENTRY AND FREE EXIT
Dual direction is safety input.
Close input can be used ), gate will close the gate, use of the above configurations to provide the ability for traffic to open...
MEGA SLIDE-X MSLXDCBB Manual - Page 23
...operation of this limited warranty in its entirety. Defective parts will be repaired or replaced with new or factory-rebuilt parts at no cost to you .
THIS LIMITED WARRANTY DOES NOT COVER ANY PROBLEMS WITH, OR RELATING TO, THE GATE OR GATE...returned pre-paid and insured, to our service center for warranty repair. LIMITED WARRANTY
LIFTMASTER 2 YEAR LIMITED WARRANTY 10 YEAR CORROSION/...
MEGA SLIDE-X MSLXDCBB Manual - Page 24
All Rights Reserved INSTALLATION CHECK OFF LIST
This Slide Gate operator is clear on proper use of gate operator (required). _____ Customer instructed on proper use in line of sight (required). _____ Hard wired contact sensors located and wired to the recommended ASTM F 2200-02 requirements.
Customer's Signature
Date
Installer's Signature
Date
Customer and installer should be pushed ...
LiftMaster MEGA SLIDE-X Reviews
We have not received any reviews for LiftMaster yet.