LiftMaster RSL12VDC Support and Manuals
Get Help and Manuals for this LiftMaster item
View All Support Options Below
Free LiftMaster RSL12VDC manuals!
Problems with LiftMaster RSL12VDC?
Ask a Question
Free LiftMaster RSL12VDC manuals!
Problems with LiftMaster RSL12VDC?
Ask a Question
Popular LiftMaster RSL12VDC Manual Pages
DC Gate Operators Overview Brochure Manual - Page 1
... (Auto Open (or Push Open Slide Gates)) Electronic Limits / Automatic Force Control Board Configuration Plug-in Loops, Anti Tailgate, Quick Close, 3-Second Pre-Motion Warning and 2-Programmable Relays. ** Cycles noted are for specific details)
Yes Yes Main Board Only With optional expansion board * 3 Years 16' 1000 lbs 250
RSL12VDC
12VDC Residential/Light Commercial DC Slide Gate Operator...
"Manufacturer's Certification for Credit" Manual - Page 1
...Traffic DC Slide Gate Operator System (Model CSL24VDC) LiftMaster CSW24V Commercial High Traffic DC Swing Gate Operator (Model CSW24V) LiftMaster CSW24VDC Commercial High Traffic DC Swing Gate Operator (Model CSW24VDC)
LiftMaster RSL12V Residential DC Slide Gate Operator System (Model RSL12V) LiftMaster RSL12VDC Residential/Light Commercial DC Slide Gate Operator (Model RSL12VDC) LiftMaster RSW12V...
RSL12VDC Installation Manual - Page 2
...
ERROR CODES 27
CONTROL BOARD LEDS 30
TROUBLESHOOTING CHART 31
APPENDIX
34
TYPES OF INSTALLATIONS 34
DETERMINE LOCATION FOR CONCRETE PAD AND OPERATOR.........35
ATTACH THE CHAIN 35
DUAL GATE SETTINGS 40
LIMIT SETUP WITH A REMOTE CONTROL 41
WIRING DIAGRAM
42
REPAIR PARTS
43
ACCESSORIES
45
WARRANTY
47
SAFETY
SAFETY SYMBOL AND SIGNAL WORD REVIEW
When you see this manual...
RSL12VDC Installation Manual - Page 13
... manual for the close direction. This input will function. CLOSE EDGE (2 Terminals)
The CLOSE EDGE input is not grounded properly the range of the remote controls will be reduced and the operator will open to lightning and surge damage. The ground wire must be disregarded during gate closing the gate will be disregarded during gate opening . Install...
RSL12VDC Installation Manual - Page 19
... of the MOVE GATE buttons to move the gate to the other control may also need adjustment.
• After ANY adjustments are set .
6.
ON
BLINKING LIMIT SETTING MODE Close limit is being set . Press and release the SET OPEN and SET CLOSE buttons simultaneously to the right. The limit setup LEDs (located next to the SET OPEN and SET CLOSE buttons) indicate...
RSL12VDC Installation Manual - Page 22
... ethernet cable to the LiftMaster Internet Gateway.
3. Create an online account by visiting www.myliftmaster.com.
4. The gate operator can then be set. All remote control codes are now erased.
ERASE LIMITS
1. Remove the entrapment protection device wires from the terminal block.
2. The SET OPEN and SET CLOSE LEDs will turn off the SET OPEN and SET CLOSE LEDs (exiting...
RSL12VDC Installation Manual - Page 23
... dial: The TIMER-TO-CLOSE (TTC) dial can be manually pushed open or closed if there is in the Troubleshooting section. 11 Error Code Display: The error code display will close the gate when the operator is a loss of the operator. The range is 0 to 180 seconds, 0 seconds is factory set to automatically close photoelectric sensors (IR's). 8 REVERSAL FORCE...
RSL12VDC Installation Manual - Page 28
... and hold the OPEN button until a new error occurs.
3.
A SECOND LATER.... AC & BATT FAIL BACKDRIVE
TO SCROLL THROUGH THE SAVED ERROR CODES
TO EXIT ERROR CODE DISPLAY
Press and release the STOP button to the most recent error (example: "01" shown below ).
TROUBLESHOOTING
To protect against fire: • Replace ONLY with "01" and going up to error "20". ERROR CODES
NOTE: When...
RSL12VDC Installation Manual - Page 29
... the second operator for alignment or
(expansion board)
obstruction. OPEN EYE/EDGE held more than 20V on main board; TROUBLESHOOTING
ERROR CODES continued... May be set limits. LiftMaster Plug-in the loop. Check harness. Failure or missing shadow loop (SHORT or OPEN - If an error is installed on a level surface and not on the battery. If OFF, restore power...
RSL12VDC Installation Manual - Page 30
...NO YES
YES YES YES
YES
YES
29 Error Code 66 67 68 69 70 71 72 73
74 75 80
81 82 83 91
93 99
Meaning OPEN EYE/EDGE held more than 3 minutes (expansion...occurred, no action required. Ensure operator is not saved it occurs, then disappear. TROUBLESHOOTING
ERROR CODES continued... Some errors are saved in the error code history and some are not. Ensure operator is engaged and free to Limit and ...
RSL12VDC Installation Manual - Page 32
... batteries by AC or solar power or replace batteries
d) Defective control board
d) Replace defective control board
Control board powers up, but motor does not run and error code b) Open fuse
b) Check fuses
display not on " detector
g) Defective control board
g) Replace defective control board
Gate moves, but will not close when setting limits. c) If on battery power only, low...
RSL12VDC Installation Manual - Page 33
...sensor causes moving gate to stop and reverse direction. TROUBLESHOOTING
TROUBLESHOOTING CHART continued... Alarm sounds for cause of both operator's Bipart switch settings. a) Double ... to open or closed is
given
a) Change setting of entrapment (obstruction) detection and correct.
Charge batteries by AC or solar power or replace batteries
On dual-gate system, incorrect gate opens first ...
RSL12VDC Installation Manual - Page 40
... to the Dual Gate section (if applicable...Model K94-37236)
Black Wire (-)
Diode +
-
20W Solar panel installation
33AH Battery -+
Black Wire (-)
Red Wire (+) +
Red Wire (+)
+
-
-
30W Solar panel installation...Slide bolts in the operator.
3. Route the battery wires (the longer set of the battery. Position solar bracket on the back of the battery.
4.
SOLAR PANEL(S)
INSTALL...
RSL12VDC Installation Manual - Page 42
APPENDIX
LIMIT SETUP WITH A REMOTE CONTROL
To set the limits using the OPEN and CLOSE buttons on the remote control again to enter limit setting mode.
2. The gate can be jogged back and forth using the OPEN and CLOSE buttons on the remote control again to set the open position. Press and release the OPEN button on the remote control...
RSL12VDC Installation Manual - Page 48
... confirmed to state.
01-37015
845 Larch Avenue Elmhurst, Illinois 60126-1196
www.liftmaster.com
© 2014, LiftMaster - Defective parts will be repaired or replaced with any product returned for warranty repair, which vary from defect in its entirety. ANY SERVICE CALL THAT DETERMINES THE PROBLEM HAS BEEN CAUSED BY ANY OF THESE ITEMS COULD RESULT IN A FEE...
LiftMaster RSL12VDC Reviews
We have not received any reviews for LiftMaster yet.