LiftMaster PPLX Support and Manuals
Get Help and Manuals for this LiftMaster item
View All Support Options Below
Free LiftMaster PPLX manuals!
Problems with LiftMaster PPLX?
Ask a Question
Free LiftMaster PPLX manuals!
Problems with LiftMaster PPLX?
Ask a Question
Popular LiftMaster PPLX Manual Pages
Installation Guide - Page 1
... controls access for up to total of reading multiple Wiegand Card protocols.
SPECIFICATIONS
POWER REQUIREMENTS 5-14 Vdc, 50 mA idle, 150 mA Max. LiftMaster 0
PPLX READER
INTRODUCTION
The LiftMaster® PassportTM' PPLX reader is a programmable single-door access control system, which may be set as a remote open or normally closed (field programmable) (refer to program the reader...
Installation Guide - Page 2
...14 Vdc + GROUND N/A N/A
WIRE COLOR GREEN WHITE VIOLET GRAY
REMOTE OPEN STANDALONE DATA-0 DATA-1 N/A N/A
ORANGE BROWN
N/A REX LATCH + TIMER...installing either the 4x40 screw
or the security screw into the hole on the bottom of reader)
WIRING
PRODUCT
MODEL/TYPE
Maglock Commercial Door Operators Commercial Gate Operators
Residential Gate Operators
MG1300 Logic 4.0 Medium Duty Logic LiftMaster...
Installation Guide - Page 3
... in approximately 10 seconds).
For Maglock, refer to page 2 for the reader. White/Black
O
White/Brown
Gate/Door
i
I
piPower Supply 12 Vdc Power Supply
Red +
Black Black
Brown
Remote Open Normally Open ] Switch
* Relay defaults to set the
Facility Code (flashing will end in the Advanced Programming section.
Record the name of their Credential Device. WIRING...
Installation Guide - Page 4
...DEVICE TO THE SYSTEM Enter Program Mode. If five incorrect passwords are entered, the reader will flash Amber to indicate Program Mode.
TO ENTER PROGRAM MODE USING THE PROGRAMMER:... Enter your password (Default is required to program the reader.
LI+LI+LI+LI+LI+ F J
(Password)
(ENTER)
NOTE: The reader will "time out" and return...
Installation Guide - Page 5
...)
NOTE: Anti-passback can activate the relay, but the remote open input is now set the reader to discourage card sharing. Press SET TIMER, then press DELETE, and then press ENTER.
(SET TIMER) (DELETE)
FJ
(ENTER)
(STAR)
(New Password - 54321)
Liici+w+Liici+H+
(STAR)
(Re-type New Password - 54321)
(ENTER)
NOTE: "12345" is enabled, it from reader's memory...
Installation Guide - Page 6
A Green LED and beep indicates Latch Timer setting update. NOTE: Setting Latch Timer for the latch timer. Press ENTER. Remote Open (Factory Default - Standalone operation) 2 - After the Program Mode "times out" (15 sec), present a valid card to the reader.
+Li+ .441-( 1
(SET TIMER) (Mode Number 1) (ENTER)
After one second.
6 The latch timer controls the reader relay. The...
Installation Guide - Page 7
... the LiftMaster® Q2010 Site Control System) using the Wiegand output. c. REMOTE OPEN (REQUEST TO EXIT) INPUT
When the Remote Open input is granted. When the Remote Open input is stored in the Advanced Programming section. TROUBLESHOOTING
LED IS FLASHING RED AND GREEN: a. CARDS DO NOT UNLOCK THE DOOR: Card reader beeps, LED flashes Red once. No facility code...
Installation Guide - Page 8
INSTRUCTION TO THE USER FCC ID: NNHDTR1
This device complies with Part 15 of purchase. Operation with non-approved equipment or unshielded cables is likely to result in materials and/or workmanship for a class B computing device, pursuant to the following two conditions: (1) this device may cause undesired operation. FOR TECHNICAL SUPPORT DIAL OUR TOLL...
LiftMaster PPLX Reviews
We have not received any reviews for LiftMaster yet.