Owners Manual
Page 2
... DIP Switches S2 DIP Switches ADJUSTMENTS Instant Reverse Device (IRD) Adjust the Barrier Arm 2-4 2 3 4 5 5 5 5 6-7 6 7 7 8-11 8 9 10 10 11 12 13-14 13 14 OPERATION AND MAINTENANCE Important Safety Instructions General Service Shear Pin Replacement Battery ADDITIONAL FEATURES Suggested Loop Sensor Locations Trap Instructions Sequence Access Management System (SAMS) with "Memory" Control...
... DIP Switches S2 DIP Switches ADJUSTMENTS Instant Reverse Device (IRD) Adjust the Barrier Arm 2-4 2 3 4 5 5 5 5 6-7 6 7 7 8-11 8 9 10 10 11 12 13-14 13 14 OPERATION AND MAINTENANCE Important Safety Instructions General Service Shear Pin Replacement Battery ADDITIONAL FEATURES Suggested Loop Sensor Locations Trap Instructions Sequence Access Management System (SAMS) with "Memory" Control...
Owners Manual
Page 8
... volt insulated wire only. Black Green White Neutral Pedestal Version Ground 120 Vac Top End of SEVERE INJURY or DEATH: • ANY maintenance to the operator or in SEVERE INJURY to persons and/or damage to run in accordance with local electrical codes. Connect AC power to...8226; Connect the green wire to the ground. 3 Do not connect any wiring or attempt to operator. See Accessories page. Upon completion of maintenance the area MUST be run the operator without consulting the wiring diagram. NOTE: The operator should be connected to service. • Disconnect power at...
... volt insulated wire only. Black Green White Neutral Pedestal Version Ground 120 Vac Top End of SEVERE INJURY or DEATH: • ANY maintenance to the operator or in SEVERE INJURY to persons and/or damage to run in accordance with local electrical codes. Connect AC power to...8226; Connect the green wire to the ground. 3 Do not connect any wiring or attempt to operator. See Accessories page. Upon completion of maintenance the area MUST be run the operator without consulting the wiring diagram. NOTE: The operator should be connected to service. • Disconnect power at...
Owners Manual
Page 15
...may be tested monthly to adjust and retest the gate operator properly can be done by a LiftMaster professional. 10. READ AND FOLLOW ALL INSTRUCTIONS. 5. Read the owner's manual. ALL maintenance MUST be level in the HORIZONTAL POSITION. The instant reverse device is obstructed while closing far ... when the gate is for the limit cam to travel between each sensor. • If the arm is level. OPERATION AND MAINTENANCE » IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS WARNING To reduce the risk of limit sensor Control Board Screws WARNING control board UP...
...may be tested monthly to adjust and retest the gate operator properly can be done by a LiftMaster professional. 10. READ AND FOLLOW ALL INSTRUCTIONS. 5. Read the owner's manual. ALL maintenance MUST be level in the HORIZONTAL POSITION. The instant reverse device is obstructed while closing far ... when the gate is for the limit cam to travel between each sensor. • If the arm is level. OPERATION AND MAINTENANCE » IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS WARNING To reduce the risk of limit sensor Control Board Screws WARNING control board UP...
Owners Manual
Page 16
...the battery manufacturer's Material Safety Data Sheets (01-30839 "MSDS Sheets, Battery, Standard"). See the Battery Test Description section for wear and lubricate ● Battery Maintenance Replace batteries. ◆ Repeat ALL procedures. Check at the intervals listed in collar. 4. Replace the batteries with a number 6 taper only.) NEVER USE A.... BATTERY HANDLING / STORAGE Refer to allow 1/4" play. • Battery voltage should be done by tapping on the Control Board Layout page). LiftMaster does not recommend storage of the pin. (Correct pin (P/N MA013) is a 2" pin with...
...the battery manufacturer's Material Safety Data Sheets (01-30839 "MSDS Sheets, Battery, Standard"). See the Battery Test Description section for wear and lubricate ● Battery Maintenance Replace batteries. ◆ Repeat ALL procedures. Check at the intervals listed in collar. 4. Replace the batteries with a number 6 taper only.) NEVER USE A.... BATTERY HANDLING / STORAGE Refer to allow 1/4" play. • Battery voltage should be done by tapping on the Control Board Layout page). LiftMaster does not recommend storage of the pin. (Correct pin (P/N MA013) is a 2" pin with...