LiftMaster CSW200501U Support and Manuals
Get Help and Manuals for this LiftMaster item
View All Support Options Below
Free LiftMaster CSW200501U manuals!
Problems with LiftMaster CSW200501U?
Ask a Question
Free LiftMaster CSW200501U manuals!
Problems with LiftMaster CSW200501U?
Ask a Question
Most Recent LiftMaster CSW200501U Questions
Antenna Range
How can I extend the range on my gate. I have to be right by it to have it open. Is there a specific...
How can I extend the range on my gate. I have to be right by it to have it open. Is there a specific...
(Posted by Ltsd123 3 years ago)
Popular LiftMaster CSW200501U Manual Pages
CSW200501U Setup and Operation Manual - Page 1
ELITE SERIES COMMERCIAL HIGH-TRAFFIC
AC GATE OPERATORS
SETUP AND OPERATION MANUAL
Model SL3000U
SL3000101U
1 HP Single Phase
SL3000103U
1 HP Three Phase
SL3000501U
1/2 HP Single Phase
Model CSW200U
CSW200101U
1 HP Single Phase
CSW200103U
1 HP Three Phase
CSW200501U
1/2 HP Single Phase
LiftMaster 845 Larch Avenue Elmhurst, IL 60126-1196
CSW200501U Setup and Operation Manual - Page 2
... ERASE ALL MONITORED ENTRAPMENT PROTECTION AND VEHICLE DETECTION DEVICES.....17
SETTINGS
18
GATE OPERATOR SETUP EXAMPLES 18
DUAL GATE SETTINGS 19
WIRING
19
SAMS WIRING WITH RELAYS NOT ENERGIZED 19
FIELD WIRING 20
MAINTENANCE
21
MAINTENANCE 21
TROUBLESHOOTING
22
DIAGNOSTIC CODES 22
OPERATOR ALARM 25
ACCESSORIES
26
REPAIR PARTS
27
SL3000U 27
CSW200U 28
WARRANTY
29
1
CSW200501U Setup and Operation Manual - Page 3
... installing or servicing ...manual. SAFETY
SAFETY SYMBOL AND SIGNAL WORD REVIEW
When you see this manual and follow all safety instructions.
• DO NOT attempt repair or service...service.
• Disconnect power at that time the unit may come from something mechanical or from the gate. Read them .
To protect against fire: • Replace ONLY with national and local electrical codes...
CSW200501U Setup and Operation Manual - Page 7
... seconds (OFF)
The gate will show the operator type, firmware version, and codes. ON The operator with the BIPART DELAY dial ON will ...side of the drive when looking out of the property, the setting will display as "SL" followed by a "20" which...The operator type will be the first to the Troubleshooting section. NOTE: For gates installed on the left when opening and be opposite....
CSW200501U Setup and Operation Manual - Page 8
... gate does not reverse off the solid
object, reduce the force setting by turning the force control slightly
clockwise.
Open and close limits, but low enough to prevent serious injury to the Troubleshooting section). Run the gate in cases where wind or environmental changes may... The timer is cancelled The gate is stopped The gate is used to view the code history (refer to a person.
CSW200501U Setup and Operation Manual - Page 11
...WITH CORRESPONDING SWITCHES Page 11
OPEN CLOSE
EXIT FAIL SWITCH
If the EXIT plug-in loop detector (model LOOPDETLM) detects a fault, faults are ignored (EXIT loop is faulted and inoperative).
ANTI TAIL SWITCH... or a stopped gate to stop and reverse. If the EXIT plug-in loop detector (model LOOPDETLM) detects a fault, then the gate will continue to close (ignores the Timer-to...
CSW200501U Setup and Operation Manual - Page 12
... times then all the LEDs will blink out the cycle count (cycle count is manually tampered with by switch settings. AUX Relay 1 N.C.
EXPANSION BOARD
AUX RELAY 1 AND 2
Normally Open (N.O.) and...an external
voltage). To determine the actual cycles that the gate operator has run (in motion). After servicing, set all three LED's blink 1,000,000's (e.g. 1 LED blinks 3 times, 2 LED blinks 6 ...
CSW200501U Setup and Operation Manual - Page 13
... Photoelectric Sensors or Edge Sensor, the functionality is based on the switch settings (located next to the terminals)
Switch set to CLOSE: gate reverses fully when it hits obstruction
OPEN CLOSE
1
... • If maintained, pauses Timer-to OPEN: gate reverses 4 seconds when it hits obstruction
Switch set to -Close at OPEN limit
• Opens a closing gate and holds open an open gate
...
CSW200501U Setup and Operation Manual - Page 15
...will be opposite. NOTE: For gates installed on the outside of the property, the setting will slide to the right when opening ...gate stops early and the operator has error number 50 (maximum run distance will be set the limits but should open the ...repeat steps 1-4 to allow you set during this cycle.
Model SL3000U
Limit Nuts
14
Limit Switches
Model CSW200U
Limit Cams
Open Limit Switch...
CSW200501U Setup and Operation Manual - Page 16
... test.
3. If the gate does not reverse off the solid object, reduce the force setting by turning the force control slightly counter-clockwise. To erase the limits, press and hold the...gate for the open gate and a rigid structure. The gate should have enough force to be set.
15
Open and close the gate with an automatic obstruction sensing feature. Repeat the test for ...
CSW200501U Setup and Operation Manual - Page 19
... visual alert to indicate if gate is manually tampered with by being pushed off of close limit. Attach alert signal (audible or visual alert system) to know when system is charging batteries (i.e. Use during servicing only to know when system is charging batteries (i.e. COMMERCIAL
Normally set to determine operator cycles. Normal gate close...
CSW200501U Setup and Operation Manual - Page 21
... CONTROL STATION
3-BUTTON CONTROL STATION
JUNCTION BOX
N.C. WIRING
To protect against fire: • Replace ONLY with fuse of each operator. BOARD
24 VAC IN
CLASS 2 SUPPLY 24 VAC
500... • DISCONNECT power BEFORE installing or servicing operator.
Solenoid Lock (Optional)
Maglock (Optional)
OR (Not Provided)
PLUG-IN LOOP DETECTOR Model LOOPDETLM
EXPANSION BOARD
POWER
NOTE:...
CSW200501U Setup and Operation Manual - Page 22
...bolts. Never use only lithium spray.
DESCRIPTION
TASK
Entrapment Protection Devices Warning Signs Manual Disconnect Drive Chain and Sprockets Belt and Pulley Gate Accessories Electrical Chassis Mounting Bolts ...wear or damage Check all for proper operation Inspect all power to the operator before servicing. Using a digital voltmeter, verify that the incoming voltage to the
operator is ...
CSW200501U Setup and Operation Manual - Page 24
...setup mode and set limits. LiftMaster Plug-in . Saved NO YES YES
YES
YES YES
YES
YES YES YES
YES
YES
YES YES YES YES YES NO YES YES YES YES YES
23 TROUBLESHOOTING
DIAGNOSTIC CODES... and then re-learn the second operator. If issue continues, replace main control board.
Wireless Second Operator Communication Error
Check the second operator for alignment or obstruction. Main control board...
CSW200501U Setup and Operation Manual - Page 30
... an implied warranty lasts, so the above limitation may not apply to you call 1-800-528-2806, toll free, before dismantling this product is originally installed, that it is free from defect in its entirety. Defective parts will be repaired or replaced with the instructions regarding installation, operation, maintenance and testing.
LiftMaster CSW200501U Reviews
We have not received any reviews for LiftMaster yet.