Installation Instructions
Page 3
...Phillips-head screws C. Du Pont de Nemours and Company. ® Registered trademark of time or in leveling dishwasher. 3 The location where the dishwasher will need to take special care in measuring dimensions and in a location where it may be needed : • copper tubing (3/8" recommended) or flexible stainless... and unloading dishes. Moisture barrier tape Make sure all these parts are within the shaded area shown in the "Cutout dimensions" section. Corner locations require a 2" (5.1 cm) minimum clearance between motor and flooring. Location Requirements Do not run ...
...Phillips-head screws C. Du Pont de Nemours and Company. ® Registered trademark of time or in leveling dishwasher. 3 The location where the dishwasher will need to take special care in measuring dimensions and in a location where it may be needed : • copper tubing (3/8" recommended) or flexible stainless... and unloading dishes. Moisture barrier tape Make sure all these parts are within the shaded area shown in the "Cutout dimensions" section. Corner locations require a 2" (5.1 cm) minimum clearance between motor and flooring. Location Requirements Do not run ...
Installation Instructions
Page 4
...cm) if height of opening is 34-1/2" (87.6 cm) at its lowest point. with wheels removed 21" (53.3 cm) SIDE VIEW 23-7/8" (60.6 cm) Cutout dimensions 24" (61 cm)** All surfaces must be free from intrusions 3-1/4" (8.3 cm) 24" (61 cm) min. 3-1/4" (8.3 cm) 34" (86.4 cm) min.* 2" ...from narrowest point of opening . *** May be compressed (not used on the underside of countertop. Product dimensions 3/4" (1.9 cm) insulation - may be increased to 33-7/8" (86 cm) by removing wheels from dishwasher. ** Minimum, measured from the lowest point on all models) 24-7/8" (63.2 cm) 24-1/2" (62...
...cm) if height of opening is 34-1/2" (87.6 cm) at its lowest point. with wheels removed 21" (53.3 cm) SIDE VIEW 23-7/8" (60.6 cm) Cutout dimensions 24" (61 cm)** All surfaces must be free from intrusions 3-1/4" (8.3 cm) 24" (61 cm) min. 3-1/4" (8.3 cm) 34" (86.4 cm) min.* 2" ...from narrowest point of opening . *** May be compressed (not used on the underside of countertop. Product dimensions 3/4" (1.9 cm) insulation - may be increased to 33-7/8" (86 cm) by removing wheels from dishwasher. ** Minimum, measured from the lowest point on all models) 24-7/8" (63.2 cm) 24-1/2" (62...
Installation Instructions
Page 12
... the control panel shown below : (models KUDS03FTPA and KUDU03FTPA) (Your model may vary slightly from picture above .) Custom door panel dimensions are : 1/8" (3.2 mm) 1/8" (3.2 mm) *This dimension is on your dishwasher before you order your custom door panel. Follow directions under Option #1 of the wood panel accordingly. 9. Not recommended for toe kicks greater than...
... the control panel shown below : (models KUDS03FTPA and KUDU03FTPA) (Your model may vary slightly from picture above .) Custom door panel dimensions are : 1/8" (3.2 mm) 1/8" (3.2 mm) *This dimension is on your dishwasher before you order your custom door panel. Follow directions under Option #1 of the wood panel accordingly. 9. Not recommended for toe kicks greater than...
Installation Instructions
Page 13
.... 23-1/2" (59.7 cm) *30-3/16" (76.7 cm) custom panel dimensions 3/4" (19.1 mm) *This dimension is for a 3/4" (19.1 mm) thick wood panel. Attach the panel assembly to the door by reinstalling the three screws on KitchenAid custom handle selection, refer to side. 6. This will hold the outer panel up...on the door frame. 3 screws 3 screws customer-supplied custom panel 13 NOTE: A customer-supplied full front panel must be made to specific dimensions. Position the outer panel on both sides, as shown, so that a cabinetmaker cut the custom panel because of the custom panel, the ...
.... 23-1/2" (59.7 cm) *30-3/16" (76.7 cm) custom panel dimensions 3/4" (19.1 mm) *This dimension is for a 3/4" (19.1 mm) thick wood panel. Attach the panel assembly to the door by reinstalling the three screws on KitchenAid custom handle selection, refer to side. 6. This will hold the outer panel up...on the door frame. 3 screws 3 screws customer-supplied custom panel 13 NOTE: A customer-supplied full front panel must be made to specific dimensions. Position the outer panel on both sides, as shown, so that a cabinetmaker cut the custom panel because of the custom panel, the ...
Installation Instructions
Page 14
...supplied custom panel with a 4-inch (10.2 cm) console only. 23-3/8" (59.3 cm) 3/4" (19.1 mm) *25-29/32" (65.8 cm) custom panel dimensions 1/8" (3.2 cm) 3 screws outer panel 2. Kit No. 8171555 (black), 8171556 (white) or 8171557 (biscuit) are attached, shorter screws maybe required. 8. mark 4 ...inner panel 1. Attach the panel assembly to attach custom panels. Position the outer panel on each side. 3 screws 1/8" (3.2 cm) *This dimension is aligned with the top of the customersupplied custom panel as shown. Drill two 3/32" pilot holes 1/2" (13 mm) deep, into the...
...supplied custom panel with a 4-inch (10.2 cm) console only. 23-3/8" (59.3 cm) 3/4" (19.1 mm) *25-29/32" (65.8 cm) custom panel dimensions 1/8" (3.2 cm) 3 screws outer panel 2. Kit No. 8171555 (black), 8171556 (white) or 8171557 (biscuit) are attached, shorter screws maybe required. 8. mark 4 ...inner panel 1. Attach the panel assembly to attach custom panels. Position the outer panel on each side. 3 screws 1/8" (3.2 cm) *This dimension is aligned with the top of the customersupplied custom panel as shown. Drill two 3/32" pilot holes 1/2" (13 mm) deep, into the...