KitchenAid KUDS03FTSS - Fully Integrated Dishwasher Support and Manuals
Get Help and Manuals for this KitchenAid item
View All Support Options Below
Free KitchenAid KUDS03FTSS manuals!
Problems with KitchenAid KUDS03FTSS?
Ask a Question
Free KitchenAid KUDS03FTSS manuals!
Problems with KitchenAid KUDS03FTSS?
Ask a Question
Most Recent KitchenAid KUDS03FTSS Questions
How Do I Make Sure That The Center Wash Arm Assembly Is Mating Properly
How do I make sure that the center wash arm assembly is mating properly with the water supply nozzle...
How do I make sure that the center wash arm assembly is mating properly with the water supply nozzle...
(Posted by wcouch2 5 years ago)
Kitchenaid Kuds03ftss Washing Problem
How do I improve water flow and washing power to the top rack of the KitchenAid KUDS03FTSS dishwashe...
How do I improve water flow and washing power to the top rack of the KitchenAid KUDS03FTSS dishwashe...
(Posted by wcouch2 5 years ago)
Dish Washer Does Not Start
Dishwasher does not start and there is some water inside at the base of the dishwasher
Dishwasher does not start and there is some water inside at the base of the dishwasher
(Posted by dudejapradeep 8 years ago)
Detergent Cup Will Not Open
(Posted by shaynes05 9 years ago)
How To Repair Kitchenaid Dishwasher Repair Kudk03it
(Posted by blLeon 9 years ago)
Popular KitchenAid KUDS03FTSS Manual Pages
User Instructions - Page 1
...in this manual and on the right-hand or left-hand side of injury, and tell you have provided an easy to reduce the chance of the dishwasher interior.... any problems you don't immediately follow instructions.
For your appliance. WARNING
You can find your complete model and serial number ready. These instructions include a "Troubleshooting" section to us at www.kitchenaid.com....
User Instructions - Page 4
They also improve drying by either using other dishwasher detergent. Add rinse aid when indicator drops to "Add" level.
■ To add rinse aid, turn the dispenser cap
to complete. Pour rinse aid into the center of 2 will have hard water or notice rings or spots, try a higher setting.
Press START/RESUME.
4 The heat dry option will take up...
User Instructions - Page 9
... months, turn off the water and power supply to hold extra silverware, knives and cooking utensils. If your dishwasher has a stainless steel exterior, a stainless steel cleaner is left in the down position when you have extra silverware, knives, or utensils requiring more room. In the winter, if the dishwasher could damage your dishwasher winterized by authorized service personnel...
User Instructions - Page 10
... option? Plastics often need towel drying. Use a heated drying option for service.
■ Dishwasher will have excessive moisture. Replace the fuse or reset the circuit breaker.
Is the water shutoff valve (if installed) turned on what is canceled or stopped before the Clean light comes on at the end of the cycle, the next wash cycle will...
User Instructions - Page 11
.... Is the home water pressure high enough for proper dishwasher filling? Use a liquid rinse aid and underload the dishwasher to allow detergent to 828 kPa) for service. Do not use heated drying.
■ White spots on plastic dishes or dishwasher interior
Are large amounts of dishes
Did you install a home water softener. Follow with a Normal wash cycle...
User Instructions - Page 12
... replace appliance light bulbs, air filters or water filters. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE OR PROVINCE TO PROVINCE. In Canada, call 1-800-422-1230. Please keep this warranty does not apply. Service must be repaired in U.S.A. LIFETIME LIMITED WARRANTY ON STAINLESS STEEL...
Installation Instructions - Page 2
... ordinances. • Install this manual and on open dishwasher door while someone grasps the rear of the dishwasher. You need to meet all electrical and plumbing national and local codes and ordinances.
2 WARNING
Tip Over Hazard Do not use dishwasher until latched.
• Observe all safety messages. The dishwasher must be performed by a qualified service
technician.
We...
Installation Instructions - Page 3
...attached to take special care in measuring dimensions and in dishwasher
• small level
• TORX® T15 screwdriver (if installing custom front panels)
• flashlight
• shallow pan
• 5/8" open-end wrench
• bath towel
• wood block
Parts needed :
• copper tubing (3/8" recommended) or flexible stainless steel braided fill line
• clamp connector or...
Installation Instructions - Page 4
...dishwasher.
** Minimum, measured from the lowest point on the underside of opening .
*** May be compressed (not used on all models)
24-7/8" (63.2 cm) 24-1/2" (62.2 cm)*
front vent
33-7/8" (86 cm) min.
REAR VIEW
4 with wheels
removed
21" (53.3 cm) SIDE VIEW 23-7/8" (60.6 cm)
Cutout dimensions... 6-5/8" (16.6 cm) if height of countertop.
Product dimensions
3/4" (1.9 cm) insulation -
Installation Instructions - Page 5
... a U.L.-listed/CSA-certified conduit connector. Do not solder within 6" (15.2 cm) from water inlet valve. Part No. 302797 grommet
Follow the kit instructions for your dishwasher. air gap
• Use an air gap if the drain hose is resistant to heat and detergent, and fits the 1" (2.5 cm) drain connector of 12 feet (3.7 m) that the electrical installation...
Installation Instructions - Page 8
...manual shutoff valve.
4.
Install the water line
Helpful Tip: Routing the water line through the left of opening to connect it passes through hole cut in a cabinet next to the dishwasher opening will be made.
* Parts...into a shallow pan to "OFF" position. copper tubing
3. Turn water shutoff valve to disposer inlet. Turn shutoff valve to get rid of drain hose if needed
rubber ...
Installation Instructions - Page 9
... through hole cut ribbed section).
2. drain hose
9
drain hose
* Parts available from local plumbing supply stores
drain hose
drain hose
Install moisture barrier (on some models)
1. This connection must be before the drain trap and at least 20" (50.8 cm) above the floor where dishwasher will be looped up and securely fastened to the...
Installation Instructions - Page 11
... handle on the back of the
shipping base. 3. Retain Allen wrench with the set screws
facing down on some models)
IMPORTANT: Do not scratch the front panel during this procedure. 1. Place the outer panel on mounting studs with Installation Instructions. Attach outer panel to the
factory-supplied full front panel as needed in place...
Installation Instructions - Page 13
..., the screw holes should be made to specific dimensions. hex head screw
9. Gently set outer panel aside.
3. do not tighten completely. Install custom panel
Option 1: For models KUDS03FTPA and KUDU03FTPA
NOTE: The handle for ...should be countersunk for the screws heads to the KitchenAid Catalog, visit www.kitchenaid.com, or call 1-800-422-1230. Attach the panel assembly to the door by ...
Installation Instructions - Page 14
...service at 800-444-1230. It is for 4" (10.2 cm) toe kick. Gently set outer panel aside.
3. Mark all edges of the panel to back of the precise dimensions...Step 10. If the installation needs a higher toe kick, ...models with four #10 x 1/2" wood screws (not supplied).
Option 2: For models KUDC03IT, KUDK03IT and KUDL03IT
All models require an accessory option to specific dimensions.
KitchenAid KUDS03FTSS Reviews
We have not received any reviews for KitchenAid yet.