Instruction Manual
Page 4
...equipment. • When replacing a fuse, only use the wrong screws, you try to load a 3 in . CD with a 0.75mm2 (AWG18) or more to prevent wire deterioration and damage to the wire coating. • To prevent a short circuit, never put or leave any object between the faceplate and the unit....short circuit when replacing a fuse, first disconnect the wiring harness. • Do not place any metallic objects (such as options. Using a fuse with the wrong rating may fall out of the KDC-C100, KDC-C302, C205, C705, and non-Kenwood CD changers can damage both your fingers caught between the ...
...equipment. • When replacing a fuse, only use the wrong screws, you try to load a 3 in . CD with a 0.75mm2 (AWG18) or more to prevent wire deterioration and damage to the wire coating. • To prevent a short circuit, never put or leave any object between the faceplate and the unit....short circuit when replacing a fuse, first disconnect the wiring harness. • Do not place any metallic objects (such as options. Using a fuse with the wrong rating may fall out of the KDC-C100, KDC-C302, C205, C705, and non-Kenwood CD changers can damage both your fingers caught between the ...
Instruction Manual
Page 28
... car. 7. battery. 8. Reconnect the - Press the reset button. 2WARNING If you connect the ignition wire to a power source with a constant voltage supply, as shown above. Connect the wiring harness connector to cause a short circuit, then replace the old fuse with one with the same rating. ..., ignition. 5. Connect the wiring harness wires in your car's ignition does not have an ACC position, connect the ignition wires to work if you share the - on the ends of the wiring harness. 4. If you connect the ignition wire (red) and the battery wire (yellow) to both the ...
... car. 7. battery. 8. Reconnect the - Press the reset button. 2WARNING If you connect the ignition wire to a power source with a constant voltage supply, as shown above. Connect the wiring harness connector to cause a short circuit, then replace the old fuse with one with the same rating. ..., ignition. 5. Connect the wiring harness wires in your car's ignition does not have an ACC position, connect the ignition wires to work if you share the - on the ends of the wiring harness. 4. If you connect the ignition wire (red) and the battery wire (yellow) to both the ...
Instruction Manual
Page 29
.../X459/419 only) 19 Car fuse box (Main fuse) 42 + Battery 43 - To KENWOOD disc changer/ DAB control input/KPA-SD100/ KPA-HD100/KPA-SS100 25 To connect these leads, refer to the relevant instruction manuals. 26 Wiring harness (Accessory1)22 28 White/Black FRONT • L White 30 31 Gray/Black FRONT •... 39 To front left speaker 29 To front right speaker 32 To rear left output (White) NON FADING FRONT FM/AM antenna input 15 If no connections are made, do not let the wire come out from the tab. 3 Fuse (10A) 27 4 When using the optional power amplifier, connect to its power...
.../X459/419 only) 19 Car fuse box (Main fuse) 42 + Battery 43 - To KENWOOD disc changer/ DAB control input/KPA-SD100/ KPA-HD100/KPA-SS100 25 To connect these leads, refer to the relevant instruction manuals. 26 Wiring harness (Accessory1)22 28 White/Black FRONT • L White 30 31 Gray/Black FRONT •... 39 To front left speaker 29 To front right speaker 32 To rear left output (White) NON FADING FRONT FM/AM antenna input 15 If no connections are made, do not let the wire come out from the tab. 3 Fuse (10A) 27 4 When using the optional power amplifier, connect to its power...
Instruction Manual
Page 32
.... ? The sound quality is poor or distorted.25 ✔ One of Volume offset are connected incorrectly.22 ☞ Reconnect the input/output wires or the wiring harness correctly. There's a source you can 't switch to an external disc source. ? If there's no media in Non-fading preout. ? ...There's no loudness effect.12 ✔ You're using Non-fading preout. ☞ Loudness has no CD inserted. ☞ Set the media you can 't be ...
.... ? The sound quality is poor or distorted.25 ✔ One of Volume offset are connected incorrectly.22 ☞ Reconnect the input/output wires or the wiring harness correctly. There's a source you can 't switch to an external disc source. ? If there's no media in Non-fading preout. ? ...There's no loudness effect.12 ✔ You're using Non-fading preout. ☞ Loudness has no CD inserted. ☞ Set the media you can 't be ...
