Intel SHG2 - Server Board Motherboard Support and Manuals
Popular Intel SHG2 Manual Pages
Product Guide - Page 9
..." on page 90)
• Two PCI-X 100 MHz/64-bit full-length expansion slots
• Three standard PCI 33 MHz/32-bit full-length expansion slots for add-in boards
Graphics
Integrated onboard ATI Rage† XL 32-bit SVGA controller
SCSI
Adaptec† AIC-7899W dual channel Ultra160 SCSI, supporting onboard Ultra 2 (LVD) wide, Ultra-wide, and Ultra160...
Product Guide - Page 12
...latest tested memory list:
http://support.intel.com/support/motherboards/server/SHG2
12
Intel Server Board SHG2 Product Guide Check the Intel Customer Support website for a current list of supported processors, see:
http://support.intel.com/support/motherboards/server/SHG2
Memory
The Intel Server Board SHG2 contains six 184-pin DIMM sockets.
DIMMs must be installed in the CPU1 socket, which...
Product Guide - Page 13
...SHG2 3D Mode Video Support with Z Buffer Disabled
Supported Supported
Supported
Supported
Supported Supported
Supported
Supported
Supported Supported
Supported
Supported
Supported Supported
Supported
-
To enable PCI-X 64-bit/133 MHz operation, you must disable the onboard SCSI controller using BIOS Setup. Supported
Supported
Supported Supported
Supported
Supported
Supported...
Product Guide - Page 14
...along with the same bandwidth.
14
Intel Server Board SHG2 Product Guide One additional USB connector is installed, then SCSI interrupts are defined by the USB Specification, Revision 1.1.
Modular RAID Capable PCI-X Slot 6
The SHG2 server board supports a modular RAID controller, such as two independent PCI functions. The Intel SHG2 baseboard provides active terminators, termination voltage...
Product Guide - Page 15
...
15 It also supports the PCI-X extension to the PCI Local Bus, Revision 1.0a.
✏ NOTE
If you install a 32/64-bit, 33/66 MHz PCI card in Add-in card slots 1 or 2, you install. This will slow the PCI-X bus to increase transmission
throughput. It is an Intel 82544GC Gigabit Ethernet Controller capable of the card...
Product Guide - Page 22
...-to-see : http://support.intel.com/support/motherboards/server/SHG2
Processor
A minimum of one 1.8 GHz Intel Xeon processor with 1.2 A +5 V standby current (in offices, computer rooms, and similar locations. Power Supply
Minimum of two 128 MB ECC, DDR 200 or 266-compliant registered SDRAM 184-pin gold DIMMs. DIMMs must be installed in order to the server board. For more information...
Product Guide - Page 26
..., registered SDRAM 184-pin gold DIMMs. A wide range of approved memory modules. Contact your sales representative or dealer for the latest tested memory list:
http://support.intel.com/support/motherboards/server/SHG2
26
Intel Server Board SHG2 Product Guide
Product Guide - Page 44
...bit SDRAM failure. Installing or removing jumpers: A jumper is partitioned as three banks. Some jumpers have such a tab, take care when using six 2 GB DIMMs.
The SDRAM interface runs at 200 MHz; If your sales representative or dealer for the latest tested memory list:
http://support.intel.com/support/motherboards/server/SHG2
44
Intel Server Board SHG2 Product Guide
The SHG2 server...
Product Guide - Page 56
... or enter BIOS Setup. POST checks the server board, processor, memory, keyboard, and most installed peripheral devices.
Note the screen display and write down the beep code you can generate, see "Using the Adaptec SCSI Utility" on page 81.
56
Intel Server Board SHG2 Product Guide Power-On Self-Test (POST)
Each time you turn on whether you have an operating system loaded...
Product Guide - Page 59
... the SSU title appears on the primary monitor. The tasks achieve complete control by keeping the task as Windows. The SSU supports ROM-DOS version 6.22. Start the SSU using the mouse or keyboard...menu.
From the Service Partition: Boot the server to the System Resource CD and start the SSU: 1.
To run the SSU from a "DOS box" running under an operating system such as the center of...
Product Guide - Page 63
... entries, time stamps for changes to view all of SDRs for the system firmware and BIOS. 3. When you start System Update, it automatically loads the SDR entries from the Intel support website:
http://support.intel.com/support/motherboards/server/SHG2
Updating the BIOS
To update the BIOS: 1. The SDR Manager window has a navigation pane on a category expands or collapses a list of the columns...
Product Guide - Page 73
...: • Upgrade the BIOS in flash memory • Update the language section of the BIOS using the new BIOS files and the BIOS upgrade utility, iFLASH.EXE. This upgrade utility allows you see the message:
Press to configure your computer supplier or from the Intel Customer Support website: http://support.intel.com/support/motherboards/server/SHG2
✏ NOTE
Please review the instructions...
Product Guide - Page 76
...It is a DOS-based program used to update the Baseboard Management Controller's firmware code.
At the C:\ prompt, type:
sys a:
3. Connect the power cord and power on the system.
76
Intel Server Board SHG2 Product Guide You can obtain the latest version of the firmware update file from : http://support.intel.com/support/motherboards/server/SHG2
2. Place a formatted diskette into the disk...
Product Guide - Page 77
... or Windows 95 system to load. 10. Place the diskette containing the FRU/SDR update files into the disk drive. 5. Follow the instructions that appear on CN47 pins 1-2 (BMC Force Update). 4. Prepare a bootable floppy diskette containing the updated BMC firmware files for future use. 8. Power on pins 11-12 of jumper CN 43 for the
SHG2 Server Board obtained...
Intel SHG2 Reviews
Do you have an experience with the Intel SHG2 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Intel yet.
Earn 750 points for your review!