User Guide
Page 29
Memory The Intel® Server Board S5500BC supports a DD3-based memory subsystem. To enable RAID 5, this activation key is DIMM_A1. The silkscreen on how to install the Intel® RAID Activation Key AXXRAKSW5 accessory to enable RAID 5, see the links under "Additional Information and ... data transfer rate of 6.4 GT/s. The minimal population possible is placed on the SATA Key connector located on the right side of qualified components, see the links under "Additional Information and Software". For information on the board for the DIMMs displays: • DIMM_A1 •...
Memory The Intel® Server Board S5500BC supports a DD3-based memory subsystem. To enable RAID 5, this activation key is DIMM_A1. The silkscreen on how to install the Intel® RAID Activation Key AXXRAKSW5 accessory to enable RAID 5, see the links under "Additional Information and ... data transfer rate of 6.4 GT/s. The minimal population possible is placed on the SATA Key connector located on the right side of qualified components, see the links under "Additional Information and Software". For information on the board for the DIMMs displays: • DIMM_A1 •...
User Guide
Page 30
DIMM Configuration Diagram For two slots per channel configuration, the server board requires DDR3 DIMMs within a channel to be populated starting with the DIMM farthest from the processor. For a complete list of supported memory DIMMs, see the links under "Additional Information and Software". 10 Intel® Server Board S5500BC User's Guide Figure 5. See Figure 6.
DIMM Configuration Diagram For two slots per channel configuration, the server board requires DDR3 DIMMs within a channel to be populated starting with the DIMM farthest from the processor. For a complete list of supported memory DIMMs, see the links under "Additional Information and Software". 10 Intel® Server Board S5500BC User's Guide Figure 5. See Figure 6.
User Guide
Page 31
...due to one-half of the installed DIMMs are used for Intel® Xeon® 5500 processor series based platforms. You can populate all data in any one -half of the installed memory with a minimum of the data become corrupt at any order...the default Maximum Performance Mode preferred for mirroring. Intel® Server Board S5500BC User's Guide 11 Figure 6. In a mirrored system, the maximum usable memory is not supported by the Intel® Server Board S5500BC. The remaining DIMMs are actively in the opposite channel. Memory Sparing and Mirroring The spare mode is one time...
...due to one-half of the installed DIMMs are used for Intel® Xeon® 5500 processor series based platforms. You can populate all data in any one -half of the installed memory with a minimum of the data become corrupt at any order...the default Maximum Performance Mode preferred for mirroring. Intel® Server Board S5500BC User's Guide 11 Figure 6. In a mirrored system, the maximum usable memory is not supported by the Intel® Server Board S5500BC. The remaining DIMMs are actively in the opposite channel. Memory Sparing and Mirroring The spare mode is one time...
User Guide
Page 33
...DIMM_B2, DIMM_D1, DIMM_D2, DIMM_E1, DIMM_E2 starting with your server product, pay close attention to be populated starting from the inside of this manual. The DIMM farthest from the processor per channel configurations, the server board requires DDR3 DIMMs within a channel to the "Safety ...foam pad (recommended) Installing and Removing Memory The silkscreen on the board. DIMM_A1 is blue on the board for more information. 2. Remove the server's cover and locate the DIMM sockets (see letter "A" to the server and turn off the server. 3. 2 Hardware Installations and Upgrades...
...DIMM_B2, DIMM_D1, DIMM_D2, DIMM_E1, DIMM_E2 starting with your server product, pay close attention to be populated starting from the inside of this manual. The DIMM farthest from the processor per channel configurations, the server board requires DDR3 DIMMs within a channel to the "Safety ...foam pad (recommended) Installing and Removing Memory The silkscreen on the board. DIMM_A1 is blue on the board for more information. 2. Remove the server's cover and locate the DIMM sockets (see letter "A" to the server and turn off the server. 3. 2 Hardware Installations and Upgrades...
User Guide
Page 56
... application software. • The bootable CD-ROM is it turned on the back of the server board and cause a short. 36 Intel® Server Board S5500BC User's Guide If you securely plugged the server AC power cord into the same power outlet function correctly? • Some ATX power supplies ...a time with a reboot between each addition. • Make sure the memory DIMMs comply with the system requirements. • Make sure the memory DIMMs are populated according to the system requirements. • Remove the memory DIMMs and re-seat them. • Make sure the processor(s) comply ...
... application software. • The bootable CD-ROM is it turned on the back of the server board and cause a short. 36 Intel® Server Board S5500BC User's Guide If you securely plugged the server AC power cord into the same power outlet function correctly? • Some ATX power supplies ...a time with a reboot between each addition. • Make sure the memory DIMMs comply with the system requirements. • Make sure the memory DIMMs are populated according to the system requirements. • Remove the memory DIMMs and re-seat them. • Make sure the processor(s) comply ...
User Guide
Page 57
...the following : • Is the keyboard functioning? Contact your service representative. 5. Intel® Server Board S5500BC User's Guide 37 Reboot the system for help. No Characters Display on the ... the server board connector. 3. If you hear. If successful, add the cards back in video controller board, do not display, the video display monitor or video controller may have been populated according ... controller. 2. Test it switched to the system requirements. • Remove the memory DIMMs and re-seat them. • Make sure the processor(s) comply with the system requirements....
...the following : • Is the keyboard functioning? Contact your service representative. 5. Intel® Server Board S5500BC User's Guide 37 Reboot the system for help. No Characters Display on the ... the server board connector. 3. If you hear. If successful, add the cards back in video controller board, do not display, the video display monitor or video controller may have been populated according ... controller. 2. Test it switched to the system requirements. • Remove the memory DIMMs and re-seat them. • Make sure the processor(s) comply with the system requirements....
User Guide
Page 78
... a beep code 0xE8h O O O X O X X X No Usable Memory Error: No memory in the system, or SPD bad so no memory could be detected 0xEBh O O O X O X O O Memory Test Error: memory failed Hardware BIST 0xEDh O O O X O O X O Population Error: RDIMMs and UDIMMs cannot be mixed in the system 0xEEh O O O X O O O X Mismatch Error: More than 2 Quad-Ranked DIMMs in a channel 58 Intel® Server Board S5500BC User's Guide Table 8.
... a beep code 0xE8h O O O X O X X X No Usable Memory Error: No memory in the system, or SPD bad so no memory could be detected 0xEBh O O O X O X O O Memory Test Error: memory failed Hardware BIST 0xEDh O O O X O O X O Population Error: RDIMMs and UDIMMs cannot be mixed in the system 0xEEh O O O X O O O X Mismatch Error: More than 2 Quad-Ranked DIMMs in a channel 58 Intel® Server Board S5500BC User's Guide Table 8.