Instruction Manual
Page 18
...;: NEVER connect a PC using a USB cable. trical shocks, TVI, BCI and other problems. w ANTENNA CONNECTOR 1 [ANT1] e ANTENNA CONNECTOR 2 [ANT2] (pgs. 17, 112) Accept a 50 ø antenna with another Icom CI-V transceiver or receiver. About the USB driver: Icom HP (http://www.icom.co.jp/world/support/ index.html) gives the USB driver and the...
...;: NEVER connect a PC using a USB cable. trical shocks, TVI, BCI and other problems. w ANTENNA CONNECTOR 1 [ANT1] e ANTENNA CONNECTOR 2 [ANT2] (pgs. 17, 112) Accept a 50 ø antenna with another Icom CI-V transceiver or receiver. About the USB driver: Icom HP (http://www.icom.co.jp/world/support/ index.html) gives the USB driver and the...
Instruction Manual
Page 24
Grounding prevents electrical shocks, TVI and other problems. STRAIGHT KEY 17 2 INSTALLATION AND CONNECTIONS ■ Required connections D Front panel CW KEY TIMER POWER HF/50MHz TRANSCEIVER TRANSMIT PHONES TUNER MONITOR BAL NR ELEC-...
Grounding prevents electrical shocks, TVI and other problems. STRAIGHT KEY 17 2 INSTALLATION AND CONNECTIONS ■ Required connections D Front panel CW KEY TIMER POWER HF/50MHz TRANSCEIVER TRANSMIT PHONES TUNER MONITOR BAL NR ELEC-...
Instruction Manual
Page 151
... is too low. • The squelch is closed. • The transceiver is too far clockwise. to turn the function OFF. wrong. D Transceiver power PROBLEM POSSIBLE CAUSE Power does not come on • Power cable is turned ON when receiving a • Push [NB] to reset p. 75 the function. ...Preamp is activated. • Push [P.AMP] (MF3) once or twice to receive or check the p. 36 SEND line of this chart, contact your nearest Icom Dealer or Service Center. p. 28 Output power is too low. • T he [RF POWER] control is set too far coun- • Rotate ...
... is too low. • The squelch is closed. • The transceiver is too far clockwise. to turn the function OFF. wrong. D Transceiver power PROBLEM POSSIBLE CAUSE Power does not come on • Power cable is turned ON when receiving a • Push [NB] to reset p. 75 the function. ...Preamp is activated. • Push [P.AMP] (MF3) once or twice to receive or check the p. 36 SEND line of this chart, contact your nearest Icom Dealer or Service Center. p. 28 Output power is too low. • T he [RF POWER] control is set too far coun- • Rotate ...
Instruction Manual
Page 152
...8226; Designate more than 64 MB. D Display PROBLEM POSSIBLE CAUSE The displayed frequency does • The dial lock function is activated. 7600 screen with "bound," "rotation" or "twist" condition. The display indicates the IC- • The screen saver function is activated. ... Main dial Brake adjustment Heavy Light 145 not change properly. • A set mode to suit your preference. 11 MAINTENANCE D Scanning PROBLEM POSSIBLE CAUSE SOLUTION REF. p. 149 • Operate the transceiver. - • Set the screen saver function in one direction. ...
...8226; Designate more than 64 MB. D Display PROBLEM POSSIBLE CAUSE The displayed frequency does • The dial lock function is activated. 7600 screen with "bound," "rotation" or "twist" condition. The display indicates the IC- • The screen saver function is activated. ... Main dial Brake adjustment Heavy Light 145 not change properly. • A set mode to suit your preference. 11 MAINTENANCE D Scanning PROBLEM POSSIBLE CAUSE SOLUTION REF. p. 149 • Operate the transceiver. - • Set the screen saver function in one direction. ...
Instruction Manual
Page 156
...before removing the transceiver's cover. w W hile pushing and holding [F-INP ENT] and [MW], push [POWER] to find the source of the problem, and replace the damaged fuse with a new, adequately rated fuse. 11 MAINTENANCE ■ Fuse replacement If a fuse blows or the transceiver stops functioning... the power amplifier, through the circuitry fuse. e R eplace the circuitry fuse as shown in set mode settings after resetting, if desired. The IC-7600 has two fuse types as below installed for transceiver protection. • DC power cable fuses ATC 30 A • Circuitry fuse ATC 5 A...
...before removing the transceiver's cover. w W hile pushing and holding [F-INP ENT] and [MW], push [POWER] to find the source of the problem, and replace the damaged fuse with a new, adequately rated fuse. 11 MAINTENANCE ■ Fuse replacement If a fuse blows or the transceiver stops functioning... the power amplifier, through the circuitry fuse. e R eplace the circuitry fuse as shown in set mode settings after resetting, if desired. The IC-7600 has two fuse types as below installed for transceiver protection. • DC power cable fuses ATC 30 A • Circuitry fuse ATC 5 A...