Instruction Manual
Page 3
... Instruction Manual before operating or maintaining this Instruction Manual and in a manner that must be avoided by recognizing a potentially hazardous situation before it occurs, and by HITACHI. Hazards that has not been specifically recommended by observing appropriate safety procedures. English IMPORTANT SAFETY INFORMATION Read and understand all of this power tool. NOTE emphasizes essential information. 3 Most accidents that result from power tool operation and maintenance...
... Instruction Manual before operating or maintaining this Instruction Manual and in a manner that must be avoided by recognizing a potentially hazardous situation before it occurs, and by HITACHI. Hazards that has not been specifically recommended by observing appropriate safety procedures. English IMPORTANT SAFETY INFORMATION Read and understand all of this power tool. NOTE emphasizes essential information. 3 Most accidents that result from power tool operation and maintenance...
Instruction Manual
Page 4
... three wire grounded power cord and grounded power supply system. (2) Avoid body contact with a polarized plug (one way. Never use an outdoor extension cord marked "W- English SAFETY GENERAL SAFETY RULES WARNING: Read and understand all instructions listed below, may result in a polarized outlet only one blade is wider than the other). Replace damaged cords immediately. Damaged cords increase the risk of electric shock. 3. Water entering a power tool...
... three wire grounded power cord and grounded power supply system. (2) Avoid body contact with a polarized plug (one way. Never use an outdoor extension cord marked "W- English SAFETY GENERAL SAFETY RULES WARNING: Read and understand all instructions listed below, may result in a polarized outlet only one blade is wider than the other). Replace damaged cords immediately. Damaged cords increase the risk of electric shock. 3. Water entering a power tool...
Instruction Manual
Page 5
... the Maintenance section of the tool may affect the tool's operation. Tool Use and Care (1) Use clamps or other condition that cannot be repaired. (4) Disconnect the plug form the power source before making any other practical way to secure and support the workpiece to a rotating part of this manual. Properly maintained tools, with the switch is left attached to a stable platform. English (4) Remove adjusting keys or wrenches before turning the tool...
... the Maintenance section of the tool may affect the tool's operation. Tool Use and Care (1) Use clamps or other condition that cannot be repaired. (4) Disconnect the plug form the power source before making any other practical way to secure and support the workpiece to a rotating part of this manual. Properly maintained tools, with the switch is left attached to a stable platform. English (4) Remove adjusting keys or wrenches before turning the tool...
Instruction Manual
Page 6
... using the power tool at the rated voltage. NEVER touch moving parts. 4. If maintenance or servicing requires the removal of a guard or safety feature, be used until repaired. 10. Use right tool. NEVER operate without all screws, bolts, and plates tightly mounted. Blades and accessories must be operated by insulated gripping surfaces when performing an operation where the cutting tool may burn out. 6 Operate power tools at a higher voltage than those specified in the tool's housing or handle...
... using the power tool at the rated voltage. NEVER touch moving parts. 4. If maintenance or servicing requires the removal of a guard or safety feature, be used until repaired. 10. Use right tool. NEVER operate without all screws, bolts, and plates tightly mounted. Blades and accessories must be operated by insulated gripping surfaces when performing an operation where the cutting tool may burn out. 6 Operate power tools at a higher voltage than those specified in the tool's housing or handle...
Instruction Manual
Page 7
... plastic parts. Carefully handle power tools. ALWAYS wear a protective mask when operating the random orbit sander in confined spaces. 24. Should a power tool be dropped or struck against hard materials inadvertently, it may cause the sanding paper to tear or shorten the life of ANSI Standard Z87.1. 18. Definitions for repairs by a Hitachi authorized service center. 14. no .......... If the tool appears to a complete stop using it...
... plastic parts. Carefully handle power tools. ALWAYS wear a protective mask when operating the random orbit sander in confined spaces. 24. Should a power tool be dropped or struck against hard materials inadvertently, it may cause the sanding paper to tear or shorten the life of ANSI Standard Z87.1. 18. Definitions for repairs by a Hitachi authorized service center. 14. no .......... If the tool appears to a complete stop using it...
Instruction Manual
Page 8
... these precautions: ⅜ Only HITACHI AUTHORIZED SERVICE CENTER should disassemble or assemble this power tool, and only genuine HITACHI replacement parts should be installed. ⅜ Clean the exterior of this Instruction Manual, including not using the power tool in wet environments. Never use solvents, gasoline or thinners on the nameplate. SAVE THESE INSTRUCTIONS AND MAKE THEM AVAILABLE TO OTHER USERS AND OWNERS OF THIS TOOL! 8 "Double insulation " means that...
... these precautions: ⅜ Only HITACHI AUTHORIZED SERVICE CENTER should disassemble or assemble this power tool, and only genuine HITACHI replacement parts should be installed. ⅜ Clean the exterior of this Instruction Manual, including not using the power tool in wet environments. Never use solvents, gasoline or thinners on the nameplate. SAVE THESE INSTRUCTIONS AND MAKE THEM AVAILABLE TO OTHER USERS AND OWNERS OF THIS TOOL! 8 "Double insulation " means that...
Instruction Manual
Page 9
... PARTS Switch Housing (B) Nameplate Lower cover (B) Dust bug Housing (A) Lower cover (A) Pad Fig. 1 Dial Fig. 2 (SV13YA Only) SPECIFICATIONS Model Motor Power source Current No-load speed Sanding pad size (Outer diameter) Sanding paper size (Outer diameter) Weight SV13YA SV13YB Single Phase, Series Commutator Motor Single Phase 120V AC 60 Hz 2.4 A 2.0 A 7,000 - 12,000/min 12,000/min 5" (125 mm) 5" (125 mm) 3.1 lbs. (1.4 kg) 9 Some illustrations in this manual. NEVER operate...
... PARTS Switch Housing (B) Nameplate Lower cover (B) Dust bug Housing (A) Lower cover (A) Pad Fig. 1 Dial Fig. 2 (SV13YA Only) SPECIFICATIONS Model Motor Power source Current No-load speed Sanding pad size (Outer diameter) Sanding paper size (Outer diameter) Weight SV13YA SV13YB Single Phase, Series Commutator Motor Single Phase 120V AC 60 Hz 2.4 A 2.0 A 7,000 - 12,000/min 12,000/min 5" (125 mm) 5" (125 mm) 3.1 lbs. (1.4 kg) 9 Some illustrations in this manual. NEVER operate...
Instruction Manual
Page 10
... to make appropriate repairs. PRIOR TO OPERATION 1. Power source Ensure that the switch is far away from the power source, use an extension cord of woodwork and metal surfaces before operation; ⅜ No flammable gas, liquid, or object at worksite. ⅜ Sanding thin steel sheet may cause overheating, resulting in a serious hazard. 5. English ASSEMBLY AND OPERATION APPLICATIONS ⅜ Roughing or finishing of woodwork...
... to make appropriate repairs. PRIOR TO OPERATION 1. Power source Ensure that the switch is far away from the power source, use an extension cord of woodwork and metal surfaces before operation; ⅜ No flammable gas, liquid, or object at worksite. ⅜ Sanding thin steel sheet may cause overheating, resulting in a serious hazard. 5. English ASSEMBLY AND OPERATION APPLICATIONS ⅜ Roughing or finishing of woodwork...
Instruction Manual
Page 11
... be cut and working efficiency. When the dial set to "6", the sander operates at the minimum speed (7,000/min). Installing the sanding paper Since the attachment is set to "1", the sander operates at the maximum speed (12,000/min). Next, use the holes along the fold as shown in the direction of arrow B to be installed easily by just pressing it from the dust outlet. 8. Sanding paper Pad...
... be cut and working efficiency. When the dial set to "6", the sander operates at the minimum speed (7,000/min). Installing the sanding paper Since the attachment is set to "1", the sander operates at the maximum speed (12,000/min). Next, use the holes along the fold as shown in the direction of arrow B to be installed easily by just pressing it from the dust outlet. 8. Sanding paper Pad...
Instruction Manual
Page 12
... cause overload of the motor, reduced service life of work. RANDOM ORBIT SANDER OPERATION WARNING: Never apply water or grinding fluid when sanding. How to the sander while sanding. How to hold the random orbit sander While gripping the housing, lightly press the sander against the surface to be sanded so that the sanding paper uniformly contacts the surface, as a standard. Material Paintwork: Sanding Repairs (scratches, rust spots) Stripping...
... cause overload of the motor, reduced service life of work. RANDOM ORBIT SANDER OPERATION WARNING: Never apply water or grinding fluid when sanding. How to the sander while sanding. How to hold the random orbit sander While gripping the housing, lightly press the sander against the surface to be sanded so that the sanding paper uniformly contacts the surface, as a standard. Material Paintwork: Sanding Repairs (scratches, rust spots) Stripping...
Instruction Manual
Page 13
... it onto the pad (Fig. 9). Polyester buff Fig. 9 13 This is still spinning right after use . The same applies when switching the power OFF. English Fig. 8 NOTE: Never turn the sander off by setting the lever to OFF (0). HOW TO INSTALL THE OPTIONAL ACCESSORIES WARNING: Be sure to switch power OFF and disconnect the plug to avoid accidents. ⅜ Mounting the polyester buff...
... it onto the pad (Fig. 9). Polyester buff Fig. 9 13 This is still spinning right after use . The same applies when switching the power OFF. English Fig. 8 NOTE: Never turn the sander off by setting the lever to OFF (0). HOW TO INSTALL THE OPTIONAL ACCESSORIES WARNING: Be sure to switch power OFF and disconnect the plug to avoid accidents. ⅜ Mounting the polyester buff...
Instruction Manual
Page 14
... electrical shock protection, carbon brush inspection and replacement on this random orbit sander with the tool to the HITACHI AUTHORIZED SERVICE CENTER when requesting repair or other maintenance. Service and repairs All quality power tools will eventually require servicing or replacement of parts because of worn-out sanding paper will be helpful if presented with loosened screws is noted. 3. In the operation and maintenance of Hitachi Power Tools must be performed by a HITACHI AUTHORIZED SERVICE CENTER, ONLY. 6. Service parts list CAUTION: Repair...
... electrical shock protection, carbon brush inspection and replacement on this random orbit sander with the tool to the HITACHI AUTHORIZED SERVICE CENTER when requesting repair or other maintenance. Service and repairs All quality power tools will eventually require servicing or replacement of parts because of worn-out sanding paper will be helpful if presented with loosened screws is noted. 3. In the operation and maintenance of Hitachi Power Tools must be performed by a HITACHI AUTHORIZED SERVICE CENTER, ONLY. 6. Service parts list CAUTION: Repair...
Instruction Manual
Page 15
... ACCESSORIES (1) Sanding paper (Velcro type) (Grain: #120) (Code No. 308519 1 (2) Dust bag (Code No. 323004 1 OPTIONAL ACCESSORIES sold separately ⅜ Sanding paper Size (Outer diameter) Type 5" (125 mm) Velcro type Grit No. The use with your tool. NEVER use replacement parts or accessories which are not sure whether it is safe to use Only authorized HITACHI replacement parts and accessories. Contact HITACHI if you are not intended for use of any obligation on the part...
... ACCESSORIES (1) Sanding paper (Velcro type) (Grain: #120) (Code No. 308519 1 (2) Dust bag (Code No. 323004 1 OPTIONAL ACCESSORIES sold separately ⅜ Sanding paper Size (Outer diameter) Type 5" (125 mm) Velcro type Grit No. The use with your tool. NEVER use replacement parts or accessories which are not sure whether it is safe to use Only authorized HITACHI replacement parts and accessories. Contact HITACHI if you are not intended for use of any obligation on the part...