Hitachi SP18VAH - 7" Disc Sander/Polisher Support and Manuals
Get Help and Manuals for this Hitachi item
View All Support Options Below
Free Hitachi SP18VAH manuals!
Problems with Hitachi SP18VAH?
Ask a Question
Free Hitachi SP18VAH manuals!
Problems with Hitachi SP18VAH?
Ask a Question
Popular Hitachi SP18VAH Manual Pages
Instruction Manual - Page 3
... indicates a potentially hazardous situations which , if not avoided, may result in the Instruction Manual before it occurs, and by WARNINGS on the power tool and in death or ... warnings and operating instructions in minor or moderate injury, or may cause machine damage. Hazards that must be avoided by HITACHI. Most accidents that has not been specifically recommended by recognizing ...
Instruction Manual - Page 5
... other practical way to secure and support the workpiece to control. (7) Check for which it on or off before using. Holding the work by unqualified personnel could result in the Maintenance section of starting . Such preventive safety measures reduce the risk of this manual. Service or maintenance performed by hand or against your model.
Instruction Manual - Page 6
English
SPECIFIC SAFETY RULES AND SYMBOLS
1. NEVER place your hands, fingers or other than those specified. NEVER operate without all guards or safety features in place and in the Instruction Manual.
7. NEVER use a power tool for extended periods. Keep all guards in abnormally fast motor revolution and may damage the unit and the motor...
Instruction Manual - Page 7
...Otherwise the
counterforce produced may damage and crack plastic parts. Should a power tool be dropped or struck ...sanding disc and wool bonnet. 19. Do not wipe them with solvent. Pay strict attention to securely grip the Sander Polisher. 21...welding machine. 23. Definitions for repairs by a Hitachi authorized service center.
14. Solvents such as a disc grinder. 22. Should the revolving...
Instruction Manual - Page 8
... grounding, you must still follow these precautions: ⅜ Only HITACHI AUTHORIZED SERVICE CENTER should disassemble or assemble this Instruction Manual, including not using the power tool in this
power tool, and only genuine HITACHI replacement parts should be installed. ⅜ Clean the exterior of this power tool, HITACHI has adopted a double insulation design. otherwise the plastic may...
Instruction Manual - Page 9
NAME OF PARTS
Lock Pin
Nameplate Housing Dial
Handle
Gear Cover
SPECIFICATIONS
Motor Power Source Current No-Load Speed Sanding Disc Size:
external diam.
Some illustrations in this manual. NEVER operate, or attempt any maintenance on your own power tool. hole diam. English
FUNCTIONAL DESCRIPTION
NOTE: The information contained in this Instruction Manual is designed to assist...
Instruction Manual - Page 10
...Damaged cord must be replaced or repaired.
4. Check the receptacle If the receptacle only loosely accepts the plug, the receptacle must be repaired. PRIOR TO OPERATION
...repairs.
English
ASSEMBLY AND OPERATION
APPLICATIONS
⅜ Sanding metal surfaces. ⅜ Preliminary sanding of metal surfaces before painting, rust removal, removing old paint
before applying paint. ⅜ Polishing...
Instruction Manual - Page 11
...to the item "Assembling and Disassembling the Wool Bonnet and Sanding Disc".
7. To stop .
ELECTRONIC SANDER POLISHER OPERATION
Motor speed is disengaged by increasing pressure on the dial...
} For polishing
} For sanding
Lock Button
Switch Trigger
Fig. 2
When using the backing pad, use a dial setting of the environment: Confirm that the wool bonnet and sanding disc is mounted under...
Instruction Manual - Page 12
...°
are used corresponding to the state of finishing and the maximum polishing effect will resume rotation at the correct motor speed.
2. Precaution after use the sander
by cutting
the motor's power supply.
Polishing with wool bonnet using fine sanding disc. Polishing with a sander using compound substance final waxing. This unit is designed to ensure that...
Instruction Manual - Page 13
...5
Lock Pin
Tuck the excess string into
Hood Fig. 6
13
q For use as a Polisher
(1) Press the lock pin to prevent it firmly against the backing pad. Washer Nut
Rubber Pad...lock pin to avoid serious trouble. English
ASSEMBLING AND DISASSEMBLING THE WOOL BONNET AND SANDING DISC
WARNING: Be sure to switch power OFF and disconnect the plug from
flying out while polishing. Backing Pad
< > ...
Instruction Manual - Page 14
... q After releasing the lock pin, check to be sure that it has returned to tighten the washer nut sufficiently. English
q For use as a Sander (Fig. 7) (1) After placing the sanding disc (optional
accessory) on the rubber pad (optional accessory), thread the washer nut (optional accessory) onto the spindle. (2) Press the lock pin to...
Instruction Manual - Page 15
Inspecting the screws Regularly inspect all service and repairs must be used, all screws and ensure that they slide freely within the brush holders. Always keep carbon brushes clean and ensure that only authorized replacement parts will be performed by a HITACHI AUTHORIZED SERVICE CENTER, ONLY.
15 Fig. 8
CAUTION:
q Using this electronic sander polisher with loosened screws is worn in...
Instruction Manual - Page 16
... ACCESSORIES.......sold separately
⅜ Rubber Pad (Code No. 953255) ⅜ Washer Nut (Code No. 953254P) ⅜ Sanding Discs (Code No. 314084-314094) ⅜ Wool Bonnet (Code No. 949103) ⅜ Wool Bonnet (Hook & Loop type) (Code No. 321895)
NOTE: Specifications are subject to change without any obligation on the part of the HITACHI.
16
English
ACCESSORIES
WARNING:
NEVER use...
Parts List - Page 2
...SCREW (W/SP. CODE NO.
1 ... 320-945 HOUSING ASS'Y
1 INCLUD.39,41,47,48
36 320-948 SETTING LABEL
1
* 37
NAME PLATE
1
38 608-VVM BALL BEARING 608VVC2PS2L
1...
1 FOR GBR (110V),USA,CAN
43 305-095 TAPPING SCREW (W/FLANGE) D4X20
2
44
HITACHI LABEL
1
--- 2 ---
* ALTERNATIVE PARTS
SP 18VA 6 -- 02 WASHER) M4X10 3
REMARKS
2 305-507 TAPPING SCREW (W/FLANGE)...GUIDE
1
15 961-501 HEX. HD.
Parts List - Page 4
....) 1
606 314-090 SANDING DISCS 180MM C-P50 (10 PCS.) 1
607 314-091 SANDING DISCS 180MM C-P60 (10 PCS.) 1
608 314-093 SANDING DISCS 180MM C-P100 (10 PCS.) 1
* 609 949-103 WOOL BONNET 180MM
1 FOR FRA,SUI,USA,CAN
610 994-322 SIDE HANDLE
1
6 -- 02
* ALTERNATIVE PARTS
Printed in Japan --- 4 --(020620N) CODE NO.
STANDARD ACCESSORIES
ITEM...
Hitachi SP18VAH Reviews
We have not received any reviews for Hitachi yet.