Hitachi WR9DMR - Power Tools 9.6V 3/8" Impact Wrench Support and Manuals
Get Help and Manuals for this Hitachi item
View All Support Options Below
Free Hitachi WR9DMR manuals!
Problems with Hitachi WR9DMR?
Ask a Question
Free Hitachi WR9DMR manuals!
Problems with Hitachi WR9DMR?
Ask a Question
Popular Hitachi WR9DMR Manual Pages
Instruction Manual - Page 2
M
N
O
N
.,
ML
Q R
S
English
IMPORTANT SAFETY INFORMATION Read and understand all of the safety precautions, warnings and operating instructions in the Instruction Manual before operating or maintaining this power tool. 3 1
R
3 24
1 5
C
D
24 5 L D
6
9 8 7
5 4
E 3
2
(B)
(A)
1
0 AB
3
H
F
J E I P
3mm 11.5mm
G
E
K
,.
Instruction Manual - Page 3
... one terminal to another battery. (2) Use battery operated tool only with the switch is designed. (3) Do not use this Instruction Manual and in this Instruction Manual. Hazards that must be avoided to follow all instructions listed below, may create a risk of fire when used for which it is dangerous and must be controlled with specifically designed battery pack. CAUTION indicates...
Instruction Manual - Page 4
...crack plastic
parts. SPECIFIC SAFETY RULES
1. Use of injury. (2) When servicing a tool, use tool for purpose not intended -for symbols
V volts
no no load speed
direct current
---/min revolutions or reciprocation per minute
8. Never touch moving parts.
3. Some examples of this type of work with solvent. IMPORTANT SAFETY INSTRUCTIONS FOR USE OF THE CORDLESS IMPACT DRIVER...
Instruction Manual - Page 5
...
4. Before using the model UC14YFA or UC24YFA or UC18YG battery charger, be stepped on (1) battery charger, (2) battery, and (3) product using battery charger, read all instructions and cautionary markings on , tripped over, or otherwise subjected to a qualified serviceman when service or repair is
dangerous. Hold the impact driver by plug when disconnecting battery charger. 7. Always wear...
Instruction Manual - Page 6
... volts). disconnect the power cord from direct sunlight and use . SPECIFICATIONS
1. Cordless Impact Driver
Model
WH9DMR
WH12DMR
WH14DMR
WH18DMR
Voltage No-Load speed
9.6 V
12 V
14.4 V
0 - 2600 / min
18 V
Capacity (Ordinary bolt)
Tightening torque (Maximum)
M5 - Cordless Impact Wrench
Model
WR9DMR
WR12DMR
WR14DMR
WR18DMR
Voltage
9.6 V
12 V
14.4 V
18 V
No-Load speed...
Instruction Manual - Page 7
....
Insert the battery to the battery charger Insert the battery into place. Make sure it may
also cause problems in red. (At 1-second intervals)
WARNING: Do not use the electrical cord if damaged. Table 2
Indications of the tool, causing injury to you or someone around you. (Fig. 1)
⅜ How to remove the battery Withdraw 5 battery from the...
Instruction Manual - Page 8
...installed on the right or left side and the angle can be used as a hook for suspending from a waist belt when required by pulling on the charger. 2. Insert the battery into the charger Insert the battery into the battery...tool main unit when carrying the tool main unit with hand, pull out the battery from the battery charger.
Remove the battery from the battery charger Supporting the battery ...
Instruction Manual - Page 9
... with the hole in the hex. Installing the bit (Impact driver) Always follow the following can occur. Using an improper socket will turn off automatically after 15 minutes. (2) The direction of the anvil B with the battery specifications and indications.
2. Installing a socket (Impact wrench) Align the plunger located in the square part of the light can be tightened. Check...
Instruction Manual - Page 10
...driving in the case of the electronic circuit parts may overheat and be switched while the impact driver... tool Hold the impact ...battery replacement, eventually resulting in line with this case, stop the
impact driver, then set...impact the nut for the screw. In this impact driver lined up some bolts before restarting impact, or manually tighten the bolt and nut to push the wrench very hard...
Instruction Manual - Page 11
... torque. Checking the condition of the power tool. Check the Screws Loose screws are dangerous. In addition, always keep carbon brushes clean and ensure that only authorized replacement parts will result in with new ones. Do not use .
Replacing carbon brushes
Take out the carbon brush by a HITACHI AUTHORIZED SERVICE CENTER, ONLY. Check with your local...
Parts List - Page 1
Hitachi Power Tools
LIST NO. G820
ELECTRIC TOOL PARTS LIST
CORDLESS IMPACT WRENCH Model WR 9DMR
2005 • 4 • 1 (E1)
1 2
3 4
16 17 18 19 20
21
501
502
502
5
6
7 8 9
10 11
12
22 23
13 14
15
24 25 26 27
28 29
31 33 32 30
31
34
35 37
36
41
40 39 38
44 43 42
45
Parts List - Page 2
...172 WASHER (S)
1
12 316-171 STOPPER
1
13 321-666 SPINDLE (D)
1
14 321-667 IDLE GEAR SET (2 PCS.)
2
15 319-914 NEEDLE ROLLER
2
16 320-877 RING GEAR (C)
1
17 319-911 WASHER... HOUSING (A). (B) SET
1
31 994-532 MACHINE SCREW (W/SP.
USED
REMARKS
1 322-727 FRONT CAP (B)
1
2 322-728 PROTECTOR (C)
1
3 319-917 TAPPING SCREW (W/SP. PARTS
ITEM NO. DESCRIPTION
NO. CODE NO. WASHER) M3X5...
Parts List - Page 3
...501 322-070 CASE
* 502
CHARGER (MODEL UC 14YFA)
* 502
CHARGER (MODEL UC 18YG)
NO. CODE NO.
SOCKET ASS'Y 8MMX33L
602 996-124...602, 603
1 INCLUD. 602, 603
1 INCLUD. 607, 608
1 INCLUD. 607, 608, 627
1
1
4 -- 05
* ALTERNATIVE PARTS
--- 3 ---
SOCKET ASS'Y 13MMX33L
607 996-123 SOCKET PIN (B)
608 873-570 O-RING (P-18)
609 996-129 HEX. SOCKET ASS'Y ... FOR IMPACT DRIVER (500G)
NO.
Parts List - Page 4
DESCRIPTION
NO.
Printed in Japan 4 -- 05 (050401N)
ITEM NO. USED
REMARKS
WR 9DMR
--- 4 --- CODE NO.
Hitachi WR9DMR Reviews
We have not received any reviews for Hitachi yet.