Hitachi SV13YA Support Question
Hitachi SV13YA Support Question
Find answers below for this question about Hitachi SV13YA - 5" Random Orbit Finishing Sander.Need a Hitachi SV13YA manual? We have 1 online manual for this item!
Question posted by Anonymous-158200 on March 30th, 2016
Hitachi Sv13ya Velcro Pad
do you have a velcro pad for hitachi sv13ya and if so how much is it.steve
Current Answers
Answer #1: Posted by TechSupport101 on March 30th, 2016 1:22 AM
TechSupport101
Member since:
May 24th, 2013 Points: 12,171,305
Member since:
May 24th, 2013 Points: 12,171,305
Hi. HelpOwl does not resell but you can order the Velcro pad from here http://www.nailgunorings.com/HITACHI_5_HOOK_LOOP_PAD_324_209_324209_SV13YA_p/324209.htm or http://www.ebay.co.uk/itm/HITACHI-SV13YA-YB-SANDER-125mm-VELCRO-PAD-BASE-SUIT-MAKITA-BO5021-BO5041-/181572079684
Related Hitachi SV13YA Manual Pages
Instruction Manual - Page 3
...and operating instructions in the Instruction Manual before it occurs, and by WARNINGS on the power tool and in this Instruction Manual and in minor or moderate injury, or may cause machine damage...avoided to observe basic safety rules or precautions. Basic safety precautions are caused by HITACHI. Most accidents that has not been specifically recommended by the failure to prevent bodily...
Instruction Manual - Page 4
...cords increase the risk of fumes.
(3) Keep bystanders children, and visitors away while operating a power tool.
Do not use the cord to install a polarized outlet. Contain long hair. Work Area
(1) Keep your finger...in the outlet, reverse the plug. Keep cord away from moving parts. Carrying tools
with your work area clean and well lit. Loose clothes, jewelry, or
long...
Instruction Manual - Page 5
... by the manufacturer for appropriate conditions.
4. Keep proper footing and balance at the rate for misalignment or binding of moving parts, breakage of the tool may affect the tool's operation. Dust mask, non-skid safety shoes, hard hat, or hearing protection must be used with the switch is unstable and may become...
Instruction Manual - Page 6
... motor air vent clean. Prolonged exposure to electric shock. NEVER operate without all guards in the Instruction Manual.
7. Don't use a power tool for applications other than those specified. The tool's motor air vent must be secure and tight.
11. English
SPECIFIC SAFETY RULES AND SYMBOLS
1. NEVER place your hands, fingers or other...
Instruction Manual - Page 7
..., cracked, or damaged.
16. NEVER leave the random orbit sander on floor and so on this tool V volts Hz .......... Definitions for repairs by a Hitachi authorized service center.
14. no .......... Pushing the random orbit sander too strongly may damage and crack plastic parts. ALWAYS operate the random orbit sander safely for finishing wood and metal surfaces and ground coats. 22...
Instruction Manual - Page 8
... parts should be installed. ⅜ Clean the exterior of this Instruction Manual, including not using the power tool in this power tool, HITACHI has adopted a double insulation design. Never use solvents, gasoline or thinners on the nameplate. "Double insulation " means that two physically separated insulation systems have been ...
Instruction Manual - Page 9
...-load speed
Sanding pad size (Outer diameter)
Sanding paper size (Outer diameter) Weight
SV13YA
SV13YB
Single Phase, Series Commutator Motor
Single Phase 120V AC 60 Hz
2.4 A
2.0 A
7,000 - 12,000/min
12,000/min
5" (125 mm)
5" (125 mm) 3.1 lbs. (1.4 kg)
9 NEVER operate, or attempt any maintenance on your own power tool.
Some illustrations in...
Instruction Manual - Page 10
... worksite. ⅜ Sanding thin steel sheet may cause overheating, resulting in the ON position, the power tool will start operating immediately and can cause serious injury.
3. English
ASSEMBLY AND OPERATION
APPLICATIONS
⅜ Roughing or finishing of woodwork and metal surfaces. ⅜ Preliminary sanding of sufficient thickness and rated capacity. PRIOR TO OPERATION...
Instruction Manual - Page 11
...the pad. Finally, press the entire sanding paper uniformly onto the pad.
7.
To adjust the speed, turn the dial shown in the direction of speed (SV13YA only) The SV13YA is set to "1", the sander ...hold the dust gate and pull it in Fig. 5. When the dial set to "6", the sander operates at the minimum speed (7,000/min). When the dial is equipped with the electric control circuit...
Instruction Manual - Page 12
...RANDOM ORBIT SANDER OPERATION
WARNING: Never apply water or grinding fluid when sanding. How to hold the random orbit sander While gripping the housing, lightly press the sander against the surface to move the random orbit sander Move the sander...2 - 4 3 - 6 3 - 6
NOTE: Please use this table as shown in Fig. 6.
English
By adjusting the dial, match the speed to the sander while sanding.
Instruction Manual - Page 13
...and-loop type as with the sanding paper, the polyester buff can be sanded.
Switching the sander ON and OFF The power can be mounted by setting the lever to ON (1) and turned off by... just pressing it onto the pad (Fig. 9). 3. English
Fig. 8 NOTE:
Never turn the sander off and unplug it. ⅷ Since the sander may suck in dust and debris, be careful not to place...
Instruction Manual - Page 14
.... Inspecting the sanding paper Since use . WARNING: Using this tool should ONLY be performed by a HITACHI AUTHORIZED SERVICE CENTER. Inspecting the carbon brushes For your continued safety and electrical shock protection, carbon brush inspection and replacement on this random orbit sander with the tool to the pad, replace the sanding paper as soon as excessive abrasion is...
Instruction Manual - Page 15
... 308522 308523
⅜ Polyester buff (Code No. 308515)
NOTE: Specifications are subject to use with your tool.
Contact HITACHI if you are not intended for use a particular replacement part or accessory with this tool. STANDARD ACCESSORIES
(1) Sanding paper (Velcro type) (Grain: #120) (Code No. 308519 1 (2) Dust bag (Code No. 323004 1
OPTIONAL ACCESSORIES sold separately...
Similar Questions
If I Want To Move The Tv 100miles, Do I Need To Secure Any Components. Thanks
(Posted by Gsasanfar 10 years ago)
Unlock Key Pad Lost Remote
How to unlock the key pad for the hitachi cpx 400
How to unlock the key pad for the hitachi cpx 400
(Posted by mcbeverly9 10 years ago)
My Tv Is An Older Model. I Have Tried To Put In Random Codes, All Of Which Were
wrong. I need a 3 number code
wrong. I need a 3 number code
(Posted by collettebrenda9 11 years ago)
Key Pad
When you push the input button,the screen reads "key pad locked"
When you push the input button,the screen reads "key pad locked"
(Posted by bfoster6 12 years ago)