Hitachi C10LA - 10" Cabinet Saw Support and Manuals
Get Help and Manuals for this Hitachi item
This item is in your list!
View All Support Options Below
Free Hitachi C10LA manuals!
Problems with Hitachi C10LA?
Ask a Question
Free Hitachi C10LA manuals!
Problems with Hitachi C10LA?
Ask a Question
Popular Hitachi C10LA Manual Pages
Instruction Manual - Page 3
... area and work . PRODUCT SPECIFICATIONS
MOTOR HP (Maximum developed 3.5
Type Induction Amps 15/7.5 Voltage 120/240 Hz 60 RPM (no load 3450 Overload Protection YES
SAW Table Size with approved safety equipment, such as dust masks that you read and understand these safety rules. It must be connected to the table saw .
- 3 - Before using your...
Instruction Manual - Page 4
...table saw . Failure to follow these safety rules.
KEEP WORK AREA CLEAN. All visitors should be properly adjusted, repaired or replaced.
21. DO NOT FORCE THE TOOL. Non-slip footwear is in some cases, a fire hazard. CHECK FOR DAMAGED OR LOOSE PARTS... benches invite accidents.
7. Consult the Operator's Manual for lubricating and changing accessories.
5. LEARN the...
Instruction Manual - Page 5
... making your table saw blade and by keeping the splitter, anti-kickback pawls and guards in detail. ALWAYS USE a push stick, especially when ripping narrow stock. PROVIDE ADEQUATE SUPPORT to prevent motor damage.
20. Clean out sawdust from the interior of the saw to a complete stop.
10. NEVER CUT METALS or materials that is covered...
Instruction Manual - Page 6
... at 240V, replace the 120V
GROUNDING INSTRUCTIONS
IN THE EVENT OF A MALFUNCTION OR
plug with ALL local codes and
ordinances.
- 6 -
To operate the table saw as shown. sure the saw is properly wired and in doubt, use proper circuit protection. grounded in any way. Always use a separate electrical circuit for 120V operation. If it repaired by a quali...
Instruction Manual - Page 7
... on the next page and the "Table
of Loose Parts" to make assembly easier, keep contents of automobile wax to assemble the table saw, plug in the power cord, or turn the switch ON until the missing or damaged part is obtained and is 13/16". Check each
R Support rod X Push stick
2 1
part with a clean dry cloth.
Instruction Manual - Page 10
... angle cut .
- 10 - OVERLOAD RESET SWITCH - Measures the distance the rip fence is tilted when set . English
GLOSSARY OF TERMS
HITACHI PROFESSIONAL TABLE SAW TERMS
MITER GAUGE -
The shaft on either side of a workpiece are , the greater the set for rip cutting that has hardened. TABLE SCALE - The amount of the workpiece. BLADE TILTING HANDWHEEL - A guide used for...
Instruction Manual - Page 11
... styrofoam (4) under the motor.
2
4. Replace the back cover (2) and then tighten the
screws (1), three for the right extension table. B-1, B-2)
NOTE: Front of the table extension before front rail fixed.
3. Attach the right front side cover (1) into right front
table rail (2). When
the front rail is removed from the cabinet stand.
4. English
ASSEMBLY AND ADJUSTMENTS...
Instruction Manual - Page 16
...right side of the saw is not in a scrap piece of the miter gauge to the desired angle. English
INSTALLING THE TABLE INSERT (FIG. K)
The table insert has been previously installed on all four ...gauge
body (3) to the miter gauge bar by using a combination square. Make sure that the table insert is square to set the pointer (4) at 0O , 15O , 30O , 45O , 60O both right and left side...
Instruction Manual - Page 17
...upward to properly align the fence can cause "kickback" and serious injury could occur. Front and rear guide the fence. Push the handle (3) down to come out of an inch. The right side is... turn the adjusting screw more than 1/4 turn at a time. 3. To change the position of the table saw blade, and turning micro-set knob (2) left or right.
4
1
- 17 - P) of the fence on the
back rail ...
Instruction Manual - Page 18
...operate the saw blade for the motor to cool, push in the switch.
To tilt the saw with the hose in the OFF position, grasp the end (or yellow part) of the table saw OFF, ...Wait about five minutes for bevel cutting, loosen the lock
knob (2) and turn the saw . English
OPERATION
BASIC SAW OPERATIONS
RAISE THE BLADE (FIG. R-1) The ON / OFF switch has a removal key. R) To raise...
Instruction Manual - Page 19
...crosscutting. forward only on the table and against the fence and must...off the table top.
The... ripping
of the table. 10.Never pull the piece...both of the table (2), finish the cut is set to cause careless ...table saw . 2. To avoid...to the table. 3....
Before using the saw ON and wait for the .... 4.
Turn the saw each and every time... the front of the saw to an angle other ...
Instruction Manual - Page 20
...not interfere with screws. Tighten miter lock handle at bevel angle other than the top of your table
saw to the desired angle, and tighten the blade bevel lock knob.
2. Remember that you can... right side groove (2) because the bevel angle may cause the blade guard to make a simple outfeed support by clamping a piece of plywood to the side of the blade that even a careless fraction of...
Instruction Manual - Page 23
... tilting mechanism should be kept clean and free of the blade raising mechanism or tilting mechanism, contact Hitachi Authorized Service Center immediately.
EE) After each five hours of your table saw cabinet and the motor.
2. Observe any other parts may create a hazard.
5. If excessive looseness is observed in any movement of the blade raising mechanism...
Instruction Manual - Page 72
...SET PLATE COVER DUST GUARD GUIDE BLOCK SPONGE WHEEL SET PLATE RETAINING CLIP LOCATION SEAT ARM BRACKET WASHER COLLAR POINTER ROLLING WHEEL
PARTS LIST
MODEL...COLLECTOR UPPER SUPPORT SUPPORT ROD ...10" STATIONARY TABLE SAW
PARTS LIST FOR SCHEMATIC
HKU# I .D. HD. HD. HD. COUNT HD. RE. SCREW CR. RE. RE. TRUSS HD. C10LA
Size #06
6203ZZ 5/16*5/8-1/16 φ6*13-1 φ16*30-3 φ10...
Parts List - Page 1
...10" STATIONARY TABLE SAW
PARTS LIST...GUIDE BLOCK
726698 237X
SPONGE
726699 237Y
WHEEL
726700 237Z
SET PLATE
326114 238D
RETAINING CLIP
726702 238G
LOCATION SEAT
726705 238K
ARM BRACKET
726707 238M
WASHER
726710 238R
COLLAR
PARTS LIST
MODEL NO. C10LA
Size
6203ZZ 5/16*5/8-1/16 φ6*13-1 φ16*30-3 φ10...REAR COVER DUST COLLECTOR UPPER SUPPORT SUPPORT ROD BRACKET BODY SHELL ...
Hitachi C10LA Reviews
Do you have an experience with the Hitachi C10LA that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Hitachi yet.
Earn 750 points for your review!