HP ProLiant 8000 Support and Manuals
Get Help and Manuals for this Hewlett-Packard item
View All Support Options Below
Free HP ProLiant 8000 manuals!
Problems with HP ProLiant 8000?
Ask a Question
Free HP ProLiant 8000 manuals!
Problems with HP ProLiant 8000?
Ask a Question
Popular HP ProLiant 8000 Manual Pages
ProLiant Server Troubleshooting Guide - Page 59
In either case, replace the PPM.
If errors are occurring, be sure that the proper drivers and support exist on your server and that you are required to enable this technology. The PPM is installed correctly. The system will continue to run without the server being powered down.
HP Servers Troubleshooting Guide
2-17 If you are having problems with PCI or PCI-X Hot...
ProLiant Server Troubleshooting Guide - Page 238
.... Use the Options ROMPaq utility to upgrade firmware on another controller and reconnected to the original controller while data was in Array Accelerator.
POST Error Messages
Table C-13: 1700 Series POST Error Messages continued
Error Code
Audible Beeps
Probable Source of Problem
1770-Slot X Drive Array - SCSI Drive Firmware Update Recommended -
Check file system to the secondary...
ProLiant 8000 Intel Pentium III Xeon 700MHz Servers Maintenance and Service Guide - Page 107
... system configuration detected. RAM failure detected. RAM failure.
Replace or remove malfunctioning memory module as indicated. Verify placement of the log. 3-10 Compaq ProLiant 8000 Intel Pentium III Xeon 700MHz Servers Maintenance and Service Guide
Table 3-2 POST Error Messages continued
Error Code
Audible Beeps
163-Time & Date Not Set
2 short
164-Memory Size Error
2 short
172...
ProLiant 8000 Intel Pentium III Xeon 700MHz Servers Maintenance and Service Guide - Page 113
... or COM4. A hardware conflict is cleared. continued 3-16 Compaq ProLiant 8000 Intel Pentium III Xeon 700MHz Servers Maintenance and Service Guide
Table 3-2 POST Error Messages continued
Error Code
Audible Beeps
806-NVRAM has
None
been reset
Please power off position.
Refer to reassign the serial port address and manually resolve the conflict.
Both external and internal serial ports...
ProLiant 8000 Intel Pentium III Xeon 700MHz Servers Maintenance and Service Guide - Page 119
... -
This
access physical system memory
controller is successful.
Try reprogramming the ROM on any cards that will resume when Array Accelerator has been reattached. 3-22 Compaq ProLiant 8000 Intel Pentium III Xeon 700MHz Servers Maintenance and Service Guide
Table 3-2 POST Error Messages continued
Error Code
Audible Beeps Probable Source of installed ISA Card(s) or run Options...
ProLiant 8000 Intel Pentium III Xeon 700MHz Servers Maintenance and Service Guide - Page 123
.... Check that the array controller is attached properly. Replace defective drive X and/or cable(s). Defective drive and/or cables detected.
Try upgrading the System ROM. continued 3-26 Compaq ProLiant 8000 Intel Pentium III Xeon 700MHz Servers Maintenance and Service Guide
Table 3-2 POST Error Messages continued
Error Code
Audible Beeps
1782-Disk Controller
None
Failure
1783-Slot...
ProLiant 8000 Intel Pentium III Xeon 700MHz Servers Maintenance and Service Guide - Page 125
...SCSI ID 0
Select F1 to continue with recovery of Problem System in Interim
Recovery Mode. Automatic Data Recovery Previously ...error from another replacement drive.
-Or-
Replace defective cables.
Replace drive X as soon as possible.
2. 3-28 Compaq ProLiant 8000 Intel Pentium III Xeon 700MHz Servers Maintenance and Service Guide
Table 3-2 POST Error Messages continued
Error Code...
ProLiant 8000 Intel Pentium III Xeon 700MHz Servers Maintenance and Service Guide - Page 127
....
This indicates that while the system was in the array accelerator memory. Array accelerator batteries failed. Run Compaq Diagnostics and replace failed assembly as indicated.
3-30 Compaq ProLiant 8000 Intel Pentium III Xeon 700MHz Servers Maintenance and Service Guide
Table 3-2 POST Error Messages continued
Error Code
Audible Beeps
1789-Slot X Drive
None
Array SCSI Drive(s)
Not...
ProLiant 8000 Intel Pentium III Xeon 700MHz Servers Maintenance and Service Guide - Page 129
...Compaq ProLiant 8000 Intel Pentium III Xeon 700MHz Servers Maintenance and Service Guide
Table 3-2 POST Error Messages continued
Error Code...memory.
Check fans for proper operation.
4. None
Drive(s) Disabled due
to accept data loss and re-enable logical drive. Adjust as needed before restarting the server... to loss of data in which the server is currently operating, and compare to continue...
ProLiant 8000 Intel Pentium III Xeon 700MHz Servers Maintenance and Service Guide - Page 131
... Utility and retest. 5. 3-34 Compaq ProLiant 8000 Intel Pentium III Xeon 700MHz Servers Maintenance and Service Guide
100 - 199, Primary Processor Test Error Codes
The 100 series of diagnostic error codes identifies failures with processor and system board functions. Port 61 error occurred. CMOS interrupt test failed. Interprocessor Communication test failed. Replace the system board and retest...
ProLiant 8000 Intel Pentium III Xeon 700MHz Servers Maintenance and Service Guide - Page 141
... information from the SmartStart and Support Software CD. 3. The time it takes to the drives, destroy data, or change or remove configuration information. To generate an ADU report, select File then Save Data from the System Utilities menu. 3-44 Compaq ProLiant 8000 Intel Pentium III Xeon 700MHz Servers Maintenance and Service Guide
Array Diagnostic Utility
Array Diagnostic...
ProLiant 8000 Intel Pentium III Xeon 700MHz Servers Maintenance and Service Guide - Page 145
... first. 3-48 Compaq ProLiant 8000 Intel Pentium III Xeon 700MHz Servers Maintenance and Service Guide
Table 3-16 ADU Diagnostic Messages continued
Message
Description
Controller is located in special "video" slot
Controller is used in this does not work , the drive may be a problem with a signature of an operating system device driver. If controller is installed in this slot...
ProLiant 8000 Intel Pentium III Xeon 700MHz Servers Maintenance and Service Guide - Page 147
... after 36 hours, replace the array accelerator board. Battery pack on the controller has been upgraded and the System Configuration Utility was not run the System Configuration Utility. Allow sufficient time for batteries to check the controller identification data. 3-50 Compaq ProLiant 8000 Intel Pentium III Xeon 700MHz Servers Maintenance and Service Guide
Table 3-16 ADU Diagnostic...
ProLiant 8000 Intel Pentium III Xeon 700MHz Servers Maintenance and Service Guide - Page 149
... array controller, but there is corrected, preventing access to be lost. continued Then, replace the original drive that failed with one or more logical drives may be in this slot. 3-52 Compaq ProLiant 8000 Intel Pentium III Xeon 700MHz Servers Maintenance and Service Guide
Table 3-16 ADU Diagnostic Messages continued
Message
Description
Logical Drive X status = OVERHEATING
The...
ProLiant 8000 Intel Pentium III Xeon 700MHz Servers Maintenance and Service Guide - Page 177
... has been reached, resulting in base memory following errors. If errors occur, information about the errors is supported.
continued 3-80 Compaq ProLiant 8000 Intel Pentium III Xeon 700MHz Servers Maintenance and Service Guide
Server Health Logs
In some servers, Server Health Logs are stored in this chapter for Server Health Log, records memory errors, as well as catastrophic hardware and...
HP ProLiant 8000 Reviews
We have not received any reviews for HP yet.