Haier IT9002 Support and Manuals
Get Help and Manuals for this Haier item
View All Support Options Below
Free Haier IT9002 manuals!
Problems with Haier IT9002?
Ask a Question
Free Haier IT9002 manuals!
Problems with Haier IT9002?
Ask a Question
Popular Haier IT9002 Manual Pages
User Manual - Page 1
Service Manual
User Manual - Page 2
IT9002
Cooker Hood
INSTALLATION AND USER'S MANUAL
User Manual - Page 3
...if they have been given supervision or instruction concerning use of the cooker hood.
...part of the cooker hood are
excessively greasy!
• When in extraction mode, air in order to the sharp edges inside the cooker hood especially during
installation and maintenance such as light bulb replacement... to it must be replaced by the manufacturer, its
service agent or similarly qualified persons...
User Manual - Page 4
...parts can not be removed for servicing or maintenance except by following incorrect installation or misuse of the appliance or use in a commercial environment. The minimum distance between the supporting... after installation of a fault with the instructions. - Under no circumstances should stay away unless they are not replaceable. Important
This instruction manual is not...
User Manual - Page 5
... upper and lower parts)
(3) Hose connector
(4) Upper wall bracket
(5) Lower wall bracket
(6) ø 4mm x 10mm Screw (6 pcs)
2
(7) Washer (2 pcs)
(8) Wall plug (8 pcs)
(9) ø 4mm x 35mm Screw (8 pcs)
3
(10)
Exhaust hose (ø15cm)
(11) Carbon filter (required for circulating air mode)
4
(12)
Cable tie
5
6
7 8
Technical specifications
Model
Voltage Product dimension...
User Manual - Page 7
The height should be measured from the top of the burners If the instructions for installation for venting outside)
When the cooker hood is to be taken into account. Installation (for the gas hob specify a greater distance, this has to be installed above an electric hob or a gas hob, the minimum distance between the hob and cooker hood must exceed 700mm.
User Manual - Page 8
Installation (for venting outside)
Tools required
Mark wall as required (see Fig. 6)
8
Fig. 5 Drill holes for mounting the body. Fig. 7 Secure hood (tighten all screws).
10mm
Fig. 8 Fit ducting adaptor. Fig. 6
Fix support plate on the wall by screws with expanding plugs.
Fig. 9
Fig. 10
User Manual - Page 10
... use . Check with your cooker hood, you do not have an outlet for exhausting air, the exhaust hose (part [10]) is not required, and the installation is similar to the one shown in the section "Installation (for replacement.
8 If you should replace the carbon filter every 2~3 months, depending on the frequency of the carbon filter...
User Manual - Page 11
...will reduce the fan speed from high to medium, to high speed. The display will return to set after the end of cooking.
Please note, the clock will show the symbol .
9 When pressed... on the extractor 15 minutes before starting to cook and leave it to confirm. Clock Setting
• To set , press key to run for approximately 15 minutes after which you should switch on /o...
User Manual - Page 12
... as shown in Fig. 14.2. You can clean your cooker hood effectively by simply using a dilute solution of fire. After rinsing and drying the filter, replace it with a clean cloth.
Care and Maintenance
IMPORTANT : DO NOT PERFORM MAINTENANCE OR CLEANING OF THE COOKER HOOD WITHOUT FIRST SWITCHING OFF THE ELECTRICITY SUPPLY...
User Manual - Page 13
...At the end of life, the appliance should not be supported by user. For more information, please contact your local ...hood
ENVIRONMENTAL PROTECTION:
This product is not shown in the user manual. It will then be dismantled by a system of selective ...human health due to the presence of the cooking process).
(13)
Install the cooker hood in a proper place where there is efficient ventilation...
User Manual - Page 14
...
as user manual. 3. Defective fan 1. Make sure power supply works normally or call electrician for fan.
3. Make sure main body mounting is burnt down.
1. Enlarge common venting hole
diameter to adjust suction. 2. The lamp is stable enough.
2. Defective installation for after service.
2. Plug-in or poor plugin.
2. Press on light button.
2. Replace lamp (please...
User Manual - Page 17
Remove 4 screws to take out maintainence cover. Then from air outlet. Remove 8 screws from damper and 4 screws from reverse side of body to take out cover sheet.
7. Maintainence cover Remove 12 screws to remove one M5 screw. Then repair fan and motor.
8.
User Manual - Page 18
9.LED light and switch control wire Use flat screwdriver to remove LED light. Switch Disconnect all responding wire
connectors for replacement.
10.
Haier IT9002 Reviews
We have not received any reviews for Haier yet.