Installation Instructions
Page 1
with a closed loop alarm contact and a closed loop tamper switch. The 6000 series comes with high density (HD) performance lens Installation Instructions T T Back housing Circuit board C NC Ð + Shield 267 266 266 Lens Front housing Figure 1. Fax: 888.723.4773 - RFI, lightning... a height of 7 to 9 feet (2.1 to undo the latch on the wall or in residential applications. 6000 Series PIR Model PI6000 - Email: [email protected] These detectors utilize dual pyroelectric sensors with 30 lb. The lens is below 14°F (-10°C) or above 122°F (50°C). ...
with a closed loop alarm contact and a closed loop tamper switch. The 6000 series comes with high density (HD) performance lens Installation Instructions T T Back housing Circuit board C NC Ð + Shield 267 266 266 Lens Front housing Figure 1. Fax: 888.723.4773 - RFI, lightning... a height of 7 to 9 feet (2.1 to undo the latch on the wall or in residential applications. 6000 Series PIR Model PI6000 - Email: [email protected] These detectors utilize dual pyroelectric sensors with 30 lb. The lens is below 14°F (-10°C) or above 122°F (50°C). ...
Installation Instructions
Page 2
...at mounting heights above 8 feet (2.4m), the locking tab must be installed at the standard 7 to 8 feet (2.1 to facilitate mounting and removal of the detector. Make sure animals cannot get within 6 feet (1.8m) of the detector's line of sight or climb on the back housing is properly positioned...circuit boards or wear a grounding strap. J4 LED - Route wiring to lock down when flat wall mounting Figure 3. Circuit Board Installing the Detector 1. Wire entry hole for surface wire runs Primary wire entry hole for corner Primary mounting hole for flat wall mounting Locking tab ...
...at mounting heights above 8 feet (2.4m), the locking tab must be installed at the standard 7 to 8 feet (2.1 to facilitate mounting and removal of the detector. Make sure animals cannot get within 6 feet (1.8m) of the detector's line of sight or climb on the back housing is properly positioned...circuit boards or wear a grounding strap. J4 LED - Route wiring to lock down when flat wall mounting Figure 3. Circuit Board Installing the Detector 1. Wire entry hole for surface wire runs Primary wire entry hole for corner Primary mounting hole for flat wall mounting Locking tab ...
Installation Instructions
Page 3
...the lens in place and gently pulling the shield away from the front housing. Email: [email protected] Maintaining the Detector When installed and used properly, the detectors provide up to the letter on the lens. 3. Clean the inside of service with a soft bristled brush or ...compressed air. Unsnap the shield from the front cover by grasping the edge of lens PI6000 Pet Immune L K J I H G F E D C B A 6000 High Density W V U T S R Q P O N ...
...the lens in place and gently pulling the shield away from the front housing. Email: [email protected] Maintaining the Detector When installed and used properly, the detectors provide up to the letter on the lens. 3. Clean the inside of service with a soft bristled brush or ...compressed air. Unsnap the shield from the front cover by grasping the edge of lens PI6000 Pet Immune L K J I H G F E D C B A 6000 High Density W V U T S R Q P O N ...
Installation Instructions
Page 4
...rating Alarm output Alarm duration Cover tamper contacts Rating Operating temperature Humidity Pulse count RFI immunity Static Immunity Lightning immunity Detection range: PI6000 Pet Immune 6000 High Density Mounting Dimensions: Width Depth Height Color 10 to 16VDC 14mA Typical 20mA max. 16 VDC, 50mA...81cm) White The unit should be connected to 1000MHz 20 kV 2.4 kV, 1.2 joules max. The equipment should be installed in accordance with tamper Listing C-UL US C-UL US g GE Security 12345 SW Leveton Drive Tualatin, OR 97062 Phone: 503-692-4052 USA & Canada: 800-547-2556 Technical Service:...
...rating Alarm output Alarm duration Cover tamper contacts Rating Operating temperature Humidity Pulse count RFI immunity Static Immunity Lightning immunity Detection range: PI6000 Pet Immune 6000 High Density Mounting Dimensions: Width Depth Height Color 10 to 16VDC 14mA Typical 20mA max. 16 VDC, 50mA...81cm) White The unit should be connected to 1000MHz 20 kV 2.4 kV, 1.2 joules max. The equipment should be installed in accordance with tamper Listing C-UL US C-UL US g GE Security 12345 SW Leveton Drive Tualatin, OR 97062 Phone: 503-692-4052 USA & Canada: 800-547-2556 Technical Service:...