GE NX-320E - Security NetworX Power Supply Support and Manuals
Most Recent GE NX-320E Questions
Popular GE NX-320E Manual Pages
Installation Guide - Page 2
...
Technical Support Sales & Literature
888-437-3287 800-547-2556
2
NX-320E Power Supply
Please refer to the current GE Security product catalog for the purchaser's purpose, the matter should be referred to cover all details or variations in part nor shall its customer solely to any third party without the written approval of the equipment described. These instructions...
Installation Guide - Page 4
... feet. A maximum of eight (8) power supply modules can be used as part of a UL Commercial Fire security system:
Unit is a microprocessor controlled remote power supply module for residential applications only. Shielded wire is not recommended that can be used for a total output count of 32, of this manual).
GENERAL DESCRIPTION
The NX-320E is compatible with the following...
Installation Guide - Page 5
...been constructed. Diagram 1: The black plastic PCB guides are grooved on one of both guides. Diagram 2: Place the first black plastic PCB guide in securely.
Once mounted, screw it in the large ...600 mA 1 Amp 1 Amp 1 Amp 1 Amp 1 Amp 1 Amp 1 Amp 1 Amp
NX-320E Power Supply
5 The smaller hole is for either vertical or horizontal placement of holes -- A screwdriver should slide...
Installation Guide - Page 6
...for any device powered from the NX-320E to 1.9 Amps. Ê
Common terminal for buss extension. Programmable output current limited to 1.9 Amps.Ê
Programmable output current limited to all devices, including the NX320E is NOT recommended. WIRING REQUIREMENTS
Table VII:1
For UL COMMERCIAL FIRE installations, a minimum of this manual.
Connect to the NX-320E board. This...
Installation Guide - Page 7
... alarm circuits must be installed using FPL, FPLP, FPLR, CL3, CL3R, or CL3P, or substitute cable permitted by National Electrical Code ANSI/NFPA70 and the Class 2, Class 3 and power-limited fire alarm circuit... DURING A BURGLAR ALARM.
THE BELL OUTPUT IS VOLTAGE ONLY. LAYOUT
NX-320E Power Supply
Recommended: Basler Model BE30614001 120VAC 60Hz 16.5VAC 50VA Class II
BELL CIRCUIT CURRENT LIMITED ...
Installation Guide - Page 8
...Service" LED will illuminate. To set the address, use the table below. User codes will only glow dimly when connected to the NetworX control panel (refer to the data terminal. The following chart furnishes the indications of this particular power supply...this manual).
8
NX-320E Power Supply UNDERSTANDING THE LEDS
The power supply module has four (4) red LEDs, which time the "Service" ...
Installation Guide - Page 9
...is saved.
& À
The new data is valid, the "Service" LED will flash and the 5 function LEDs will emit a triple error beep (beep, beep, beep), and remain in the Program Mode ... now in that segment awaiting a valid entry.
NX-320E Power Supply
9 PROGRAMMING
A. If the "Go To Program Code" is saved.
Programming a Location:
If an attempt is
`^XZ
Enters the Program Mode.
XII...
Installation Guide - Page 11
...NX-320E Power Supply
11 As before, you will emit a triple beep, indicating an error, and remain in that corresponds to select the particular event that numerous features can be displayed. If an attempt is selected for the specific events that location. After the desired setting...Siren (temporal) 26 Fire Trouble
5 Line Seizure
16 Any ....) 21 Armed
32
Code Entry (set to the next segment...
Installation Guide - Page 14
...14).
14
NX-320E Power Supply Segment 1 corresponds to user 20. Segment 10 corresponds to restrict certain codes from activating certain outputs. C (see Table XII:2 on page 14). LOCATION 9
CODES 11-20 ...A - The LEDs correspond to user 31; "Off" if it will not.
3 "On" if code will activate Output B; "Off" if it will activate Output A; C (see Table XII:2 on page...
Installation Guide - Page 15
...before a report is sent or a Service light will report a Siren Tamper to outputs A -
The LEDs correspond to the central station.
5-8 Reserved
NX-320E Power Supply
15
Segment 1 corresponds to user 81...enabled, the power supply module will report Low Battery to the central station.
4 On enables Siren Tamper/Trouble reporting
If enabled, the power supply module will illuminate...
Installation Guide - Page 16
...= Partition 5 6 = Partition 6 7 = Partition 7 8 = Partition 8
_ _
5 = Partition 5 6 = Partition 6 7 = Partition 7 8 = Partition 8
16
NX-320E Power Supply XIII. "Off" for inverted output.
5 = "On" disables output during listen-in 1 = Partition 1
seconds.
2 = Partition 2
2 = "On" if latched until code is
entered.
4 = "On" for inverted output.
5 = "On" disables output during listen...
Installation Guide - Page 17
...
2
2
2
2
2
2
2
2
Output #C 3
3
3
3
3
3
3
3
3
3
10
14 Codes 21-30 Output Enable (Circle the numbers to program)
User
21 22 23 24 25 26 27 28 29 30
Output ...Codes 91-99 Output Enable (Circle the numbers to program)
User
91 92 93 94 95 96 97 98 99
Output #A 1
1
1
1
1
1
1
1
1
Output #B 2
2
2
2
2
2
2
2
2
Output #C 3
3
3
3
3
3
3
3
3
NX-320E Power Supply...
Installation Guide - Page 18
Off follows control 2=On enables periodic battery test 3=On enables low battery reporting 4=On enables siren tamper/trouble reporting
DEFAULT 5 0
5=Reserved 6=Reserved 7=Reserved 8=Reserved
DATA ___ ___
18
NX-320E Power Supply LOC 18
19
PAGE 15
15
DESCRIPTION A/C Delay (in minutes) Dynamic Battery Test (in minutes) Device Options (Circle the numbers to program) 1=On for...
Installation Guide - Page 20
... Fire control
Main
800-727-2339
Outside the US
903-845-6941
Web: www.gesecurity.com
Technical Support 888-437-3287 Sales & Literature 800-547-2556
NX320EIG05 REV G (June 2005) SPECIFICATIONS
NX-320E DIMENSIONS
CURRENT DRAW
AUXILIARY POWER BATTERY OPERATING TEMPERATURE SHIPPING WEIGHT
2.0" Wide 9.0" High 4.0" Deep
AC Input: 120V, 60Hz, 650mA 10 mA Standby 16...
GE NX-320E Reviews
Do you have an experience with the GE NX-320E that you would like to share?
Earn 750 points for your review!
We have not received any reviews for GE yet.
Earn 750 points for your review!