User Manual
Page 1
45600 Wireless Lighting Control Remote Manual 18 • Individual Z-Wave devices • Groups • Lighting scenes Groups can include up to 232 devices Scenes can include up to 32 devices Compatible with all Z-WAVE products.
45600 Wireless Lighting Control Remote Manual 18 • Individual Z-Wave devices • Groups • Lighting scenes Groups can include up to 232 devices Scenes can include up to 32 devices Compatible with all Z-WAVE products.
User Manual
Page 2
... this guide for purchasing the GE SmartHome™ Remote. For best results, please read and perform all refer to 232 Z-Wave enabled devices. Please note: The terms "Device", "Node" and "Light" all the remaining instructions before using the remote. You can act as the primary controller. All other applications. This remote allows you must be operated in...
... this guide for purchasing the GE SmartHome™ Remote. For best results, please read and perform all refer to 232 Z-Wave enabled devices. Please note: The terms "Device", "Node" and "Light" all the remaining instructions before using the remote. You can act as the primary controller. All other applications. This remote allows you must be operated in...
User Manual
Page 3
...control the On/Off status of old batteries promptly and properly. Press LIGHT again. (Green LED blinks rapidly) 5. Do not burn or bury them to your home network without assigning it sends its user settings while replacing the batteries. NOT FOR USE WITH MEDICAL OR LIFE SUPPORT EQUIPMENT Z-Wave... that can also be referred to as include a node, group or scene. ADDING A DEVICE (NODE / LIGHT) TO THE NETWORK In order to control the lights, they must be referred to use the remote for an extended period, remove the batteries. Press ADD once. (Red LED blinks once) 3. Remove a ...
...control the On/Off status of old batteries promptly and properly. Press LIGHT again. (Green LED blinks rapidly) 5. Do not burn or bury them to your home network without assigning it sends its user settings while replacing the batteries. NOT FOR USE WITH MEDICAL OR LIFE SUPPORT EQUIPMENT Z-Wave... that can also be referred to as include a node, group or scene. ADDING A DEVICE (NODE / LIGHT) TO THE NETWORK In order to control the lights, they must be referred to use the remote for an extended period, remove the batteries. Press ADD once. (Red LED blinks once) 3. Remove a ...
User Manual
Page 9
...once. NOTE: If the red LED emits one long, steady blink, the device has not been successfully deleted from All Control. Press the digit key for GE Z-Wave devices is activated. 2. Repeat steps 1-2 if this occurs. Any ON or OFF button can be needed if the device... All-On and All-Off commands. 1. Deleting Devices (Lights / Nodes) from All Control. 5. 8 CONTROLLING SCENES To control a scene, perform the following steps: 1. Press SCENE once. (Red LED blinks once) The remote will stay in this occurs. Turning All Devices (Lights / Nodes) On or Off To turn all devices on...
...once. NOTE: If the red LED emits one long, steady blink, the device has not been successfully deleted from All Control. Press the digit key for GE Z-Wave devices is activated. 2. Repeat steps 1-2 if this occurs. Any ON or OFF button can be needed if the device... All-On and All-Off commands. 1. Deleting Devices (Lights / Nodes) from All Control. 5. 8 CONTROLLING SCENES To control a scene, perform the following steps: 1. Press SCENE once. (Red LED blinks once) The remote will stay in this occurs. Turning All Devices (Lights / Nodes) On or Off To turn all devices on...
User Manual
Page 13
...reset your network, perform the following steps: 1. Enter 9 6 7 on the numeric keypad. 3. Add devices, groups, and scenes to the GE SmartHome™ remote, as well as receives information from the network NOTE: If the red LED emits one long, steady blink, the network has not been successfully.... Enter 9 6 9 on deleting devices from this occurs. Reset all device and Z-Wave network information. Put the source remote into programming mode so that it sends its information to the new remote as instructed in the section on the numeric keypad. 3. When the green LED blinks twice...
...reset your network, perform the following steps: 1. Enter 9 6 7 on the numeric keypad. 3. Add devices, groups, and scenes to the GE SmartHome™ remote, as well as receives information from the network NOTE: If the red LED emits one long, steady blink, the network has not been successfully.... Enter 9 6 9 on deleting devices from this occurs. Reset all device and Z-Wave network information. Put the source remote into programming mode so that it sends its information to the new remote as instructed in the section on the numeric keypad. 3. When the green LED blinks twice...
User Manual
Page 15
... button on the GE remote. Operation of the device." Assign Z-Wave controlled appliances to be removed from "All" control setting. Z-Wave devices controlling appliances should be pressed before pressing device numbers 10-18. 2. Do Not include Z-Wave devices in a different room than the controlled appliance, also an unintentional activation may be powered on control. Do Not use Z-Wave devices to the...
... button on the GE remote. Operation of the device." Assign Z-Wave controlled appliances to be removed from "All" control setting. Z-Wave devices controlling appliances should be pressed before pressing device numbers 10-18. 2. Do Not include Z-Wave devices in a different room than the controlled appliance, also an unintentional activation may be powered on control. Do Not use Z-Wave devices to the...
User Manual
Page 16
... screen TV, etc.) between the remote controller and the destination device, the type of construction and the number of Z-Wave enabled devices installed in China Hecho en China 45600-2 © JASCO 2009 Z-Wave is a registered US trademark or Zensys A/S Z-Wave enabled devices should never be used ...dead-spots". www.jascoproducts.com Made in the control network. Things to work properly alongside 802.11 wireless computer networks, Bluetooth and other 2.4GHz or 5.8GHz devices. 15 Wireless Range: This device complies with the Z-Wave standard of open-air, line of sight transmission...
... screen TV, etc.) between the remote controller and the destination device, the type of construction and the number of Z-Wave enabled devices installed in China Hecho en China 45600-2 © JASCO 2009 Z-Wave is a registered US trademark or Zensys A/S Z-Wave enabled devices should never be used ...dead-spots". www.jascoproducts.com Made in the control network. Things to work properly alongside 802.11 wireless computer networks, Bluetooth and other 2.4GHz or 5.8GHz devices. 15 Wireless Range: This device complies with the Z-Wave standard of open-air, line of sight transmission...
