Manual/User Guide
Page 3
... system frame to touch parts (cover and base) other than parts to which the HDD is connected to Signal Ground (SG). 3.2 Mounting 3.2 Mounting For information on mounting, see the "FUJITSU 2.5-INCH HDD INTEGRATION GUIDANCE (C141-E144)." (1) Orientation The disk drives can be 0.49N•m (5kgf•cm). The tightening torque must be mounted in...
... system frame to touch parts (cover and base) other than parts to which the HDD is connected to Signal Ground (SG). 3.2 Mounting 3.2 Mounting For information on mounting, see the "FUJITSU 2.5-INCH HDD INTEGRATION GUIDANCE (C141-E144)." (1) Orientation The disk drives can be 0.49N•m (5kgf•cm). The tightening torque must be mounted in...
Manual/User Guide
Page 5
Figure 3.3 Location of breather hole is shown as Figure 3.3. 3.2 Mounting Because of breather hole mounted to the HDD, do not allow this to block. Locating of breather C141-E274 3-5 For breather hole of Figure 3.3, at least, do not allow its around φ 3 to close during mounting.
Figure 3.3 Location of breather hole is shown as Figure 3.3. 3.2 Mounting Because of breather hole mounted to the HDD, do not allow this to block. Locating of breather C141-E274 3-5 For breather hole of Figure 3.3, at least, do not allow its around φ 3 to close during mounting.
Manual/User Guide
Page 7
...such as loud speakers. Ensure that the disk drive is not affected by the edges. (6) Handling cautions Please keep the following cautions, and handle the HDD under the safety environment. Do not touch the printed circuit board, but hold it too hard, the cover and the spindle motor contact, ...which may cause damage to the disk drive. C141-E274 3-7 Damage: Do not press the cover of...
...such as loud speakers. Ensure that the disk drive is not affected by the edges. (6) Handling cautions Please keep the following cautions, and handle the HDD under the safety environment. Do not touch the printed circuit board, but hold it too hard, the cover and the spindle motor contact, ...which may cause damage to the disk drive. C141-E274 3-7 Damage: Do not press the cover of...
Manual/User Guide
Page 8
...ESD mat on it. Figure 3.6 Handling cautions - Installation (1) Please use an electric driver. M3 0.49N · m (5 kgf · cm). - Do not hit HDD each other. General notes Wrist strap Use the Wrist strap. Recommended equipments ESD Shock Contents Wrist strap ESD mat Low shock driver Model JX-1200...-3056-8 SKY-8A (Color Seiden Mat) SS-6500 Maker SUMITOMO 3M Achilles HIOS 3-8 C141-E274 Do not place HDD vertically to avoid falling down. HDD is occasionally damaged by the impact of the driver. (2) Please observe the tightening torque of a low impact when you use ...
...ESD mat on it. Figure 3.6 Handling cautions - Installation (1) Please use an electric driver. M3 0.49N · m (5 kgf · cm). - Do not hit HDD each other. General notes Wrist strap Use the Wrist strap. Recommended equipments ESD Shock Contents Wrist strap ESD mat Low shock driver Model JX-1200...-3056-8 SKY-8A (Color Seiden Mat) SS-6500 Maker SUMITOMO 3M Achilles HIOS 3-8 C141-E274 Do not place HDD vertically to avoid falling down. HDD is occasionally damaged by the impact of the driver. (2) Please observe the tightening torque of a low impact when you use ...