Manual/User Guide
Page 3
... Figure 3.2. C141-E245 3-3 3.2 Mounting 3.2 Mounting For information on mounting, see the "FUJITSU 2.5-INCH HDD INTEGRATION GUIDANCE (C141-E144)." (1) Orientation The disk drives can be 0.49N•m (5kgf•cm). When attaching the HDD to the system frame, do not allow the system frame to touch parts (cover and... base) other than parts to which the HDD is connected to Signal Ground (SG). ...
... Figure 3.2. C141-E245 3-3 3.2 Mounting 3.2 Mounting For information on mounting, see the "FUJITSU 2.5-INCH HDD INTEGRATION GUIDANCE (C141-E144)." (1) Orientation The disk drives can be 0.49N•m (5kgf•cm). When attaching the HDD to the system frame, do not allow the system frame to touch parts (cover and... base) other than parts to which the HDD is connected to Signal Ground (SG). ...
Manual/User Guide
Page 5
For breather hole of Figure 3.3, at least, do not allow its around φ 3 to close during mounting. 3.2 Mounting IMPORTANT Because of breather hole mounted to the HDD, do not allow this to block. Locating of breather C141-E254 3-5 Figure 3.3 Location of breather hole is shown as Figure 3.3.
For breather hole of Figure 3.3, at least, do not allow its around φ 3 to close during mounting. 3.2 Mounting IMPORTANT Because of breather hole mounted to the HDD, do not allow this to block. Locating of breather C141-E254 3-5 Figure 3.3 Location of breather hole is shown as Figure 3.3.
Manual/User Guide
Page 7
...keep the following cautions, and handle the HDD under the safety environment. Damage: Do not press the cover of the disk drive. C141-E245 3-7 Pressing it by external magnetic fields. Do not touch the printed circuit board, but hold it too hard, the cover and the spindle motor contact,... which may cause damage to the disk drive. 3.2 Mounting (5) Service area Figure 3.5 shows how the drive must be accessed (service areas) during and after installation. Static: When ...
...keep the following cautions, and handle the HDD under the safety environment. Damage: Do not press the cover of the disk drive. C141-E245 3-7 Pressing it by external magnetic fields. Do not touch the printed circuit board, but hold it too hard, the cover and the spindle motor contact,... which may cause damage to the disk drive. 3.2 Mounting (5) Service area Figure 3.5 shows how the drive must be accessed (service areas) during and after installation. Static: When ...
Manual/User Guide
Page 8
...-8 SKY-8A (Color Seiden Mat) SS-6500 Maker SUMITOMO 3M Achilles HIOS 3-8 C141-E245 Installation Conditions - General notes Wrist strap Use the Wrist strap. HDD is occasionally damaged by the impact of the driver. (2) Please observe the tightening torque of a low impact when you use an electric driver. Figure 3.6 ...Handling cautions - Do not hit HDD each other. ESD mat Shock absorbing mat Place the shock absorbing mat on the operation table, and place ESD mat on it.
...-8 SKY-8A (Color Seiden Mat) SS-6500 Maker SUMITOMO 3M Achilles HIOS 3-8 C141-E245 Installation Conditions - General notes Wrist strap Use the Wrist strap. HDD is occasionally damaged by the impact of the driver. (2) Please observe the tightening torque of a low impact when you use an electric driver. Figure 3.6 ...Handling cautions - Do not hit HDD each other. ESD mat Shock absorbing mat Place the shock absorbing mat on the operation table, and place ESD mat on it.