Manual/User Guide
Page 1
CHAPTER 3 Installation Conditions 3.1 Dimensions 3.2 Mounting 3.3 Connections with Host System This chapter gives the external dimensions, installation conditions, surface temperature conditions, cable connections, and switch settings of the hard disk drives. C141-E245 3-1
CHAPTER 3 Installation Conditions 3.1 Dimensions 3.2 Mounting 3.3 Connections with Host System This chapter gives the external dimensions, installation conditions, surface temperature conditions, cable connections, and switch settings of the hard disk drives. C141-E245 3-1
Manual/User Guide
Page 2
Installation Conditions 3.1 Dimensions Figure 3.1 illustrates the dimensions of the connector pins Figure 3.1 Dimensions 3-2 C141-E245 All dimensions are in mm. *1 The PCA and connectors are not included in these dimensions. *2 Dimension from the center of the user tap to the base of the connector pins *3 Length of the connector pins *4 Dimension from the outer edge of the user tap to the center of the connector pins *5 Dimension from the outer edge of the user tap to the innermost edge of the disk drive.
Installation Conditions 3.1 Dimensions Figure 3.1 illustrates the dimensions of the connector pins Figure 3.1 Dimensions 3-2 C141-E245 All dimensions are in mm. *1 The PCA and connectors are not included in these dimensions. *2 Dimension from the center of the user tap to the base of the connector pins *3 Length of the connector pins *4 Dimension from the outer edge of the user tap to the center of the connector pins *5 Dimension from the outer edge of the user tap to the innermost edge of the disk drive.
Manual/User Guide
Page 3
... the system frame to touch parts (cover and base) other than parts to Signal Ground (SG). The mounting frame is connected to which the HDD is zero. IMPORTANT Use M3 screw for the mounting screw and the screw length should satisfy the specification in any direction. (2) Frame The MR head bias of the HDD disk enclosure (DE) is attached. C141...
... the system frame to touch parts (cover and base) other than parts to Signal Ground (SG). The mounting frame is connected to which the HDD is zero. IMPORTANT Use M3 screw for the mounting screw and the screw length should satisfy the specification in any direction. (2) Frame The MR head bias of the HDD disk enclosure (DE) is attached. C141...
Manual/User Guide
Page 4
if it is not possible to satisfy them, contact us. Bottom surface mounting DE 2 A Frame of system cabinet 2.5 2.5 2.5 Side surface 2.5 mounting PCA B Frame of system cabinet 3.0 or less Screw Details of mounting Note) These dimensions are recommended values; Installation Conditions (3) Limitation of A 3.0 or less Screw Figure 3.2 Mounting frame structure 3-4 C141-E245
if it is not possible to satisfy them, contact us. Bottom surface mounting DE 2 A Frame of system cabinet 2.5 2.5 2.5 Side surface 2.5 mounting PCA B Frame of system cabinet 3.0 or less Screw Details of mounting Note) These dimensions are recommended values; Installation Conditions (3) Limitation of A 3.0 or less Screw Figure 3.2 Mounting frame structure 3-4 C141-E245
Manual/User Guide
Page 5
For breather hole of Figure 3.3, at least, do not allow its around φ 3 to close during mounting. Locating of breather C141-E254 3-5 3.2 Mounting IMPORTANT Because of breather hole mounted to the HDD, do not allow this to block. Figure 3.3 Location of breather hole is shown as Figure 3.3.
For breather hole of Figure 3.3, at least, do not allow its around φ 3 to close during mounting. Locating of breather C141-E254 3-5 3.2 Mounting IMPORTANT Because of breather hole mounted to the HDD, do not allow this to block. Figure 3.3 Location of breather hole is shown as Figure 3.3.
Manual/User Guide
Page 6
... points and standard values No. Regardless of the DE. Measurement point Temperature 1 DE cover 60 °C max 3-6 C141-E245 Installation Conditions (4) Ambient temperature The temperature conditions for a disk drive mounted in a cabinet refer to prevent the DE surface cover temperature from the disk drive. The ambient temperature must satisfy the temperature conditions described in Section 1.4, and the airflow must meet the standards...
... points and standard values No. Regardless of the DE. Measurement point Temperature 1 DE cover 60 °C max 3-6 C141-E245 Installation Conditions (4) Ambient temperature The temperature conditions for a disk drive mounted in a cabinet refer to prevent the DE surface cover temperature from the disk drive. The ambient temperature must satisfy the temperature conditions described in Section 1.4, and the airflow must meet the standards...
Manual/User Guide
Page 7
... cautions, and handle the HDD under the safety environment. C141-E245 3-7 Do not touch the printed circuit board, but hold it too hard, the cover and the spindle motor contact, which may cause damage to the disk drive. Pressing it by external magnetic fields. 3.2 Mounting (5) Service area Figure 3.5 shows how the drive must be accessed (service areas) during and after installation.
... cautions, and handle the HDD under the safety environment. C141-E245 3-7 Do not touch the printed circuit board, but hold it too hard, the cover and the spindle motor contact, which may cause damage to the disk drive. Pressing it by external magnetic fields. 3.2 Mounting (5) Service area Figure 3.5 shows how the drive must be accessed (service areas) during and after installation.
Manual/User Guide
Page 8
...driver Model JX-1200-3056-8 SKY-8A (Color Seiden Mat) SS-6500 Maker SUMITOMO 3M Achilles HIOS 3-8 C141-E245 HDD is occasionally damaged by the impact of the driver. (2) Please observe the tightening torque of a low impact when you use an electric driver. ESD mat Shock absorbing mat Place the shock absorbing mat on the operation... table, and place ESD mat on it. Do not place HDD vertically to avoid falling down. Do not drop. Do not stack when carrying. Do not hit HDD each other. Installation (1) Please use the driver of the screw strictly....
...driver Model JX-1200-3056-8 SKY-8A (Color Seiden Mat) SS-6500 Maker SUMITOMO 3M Achilles HIOS 3-8 C141-E245 HDD is occasionally damaged by the impact of the driver. (2) Please observe the tightening torque of a low impact when you use an electric driver. ESD mat Shock absorbing mat Place the shock absorbing mat on the operation... table, and place ESD mat on it. Do not place HDD vertically to avoid falling down. Do not drop. Do not stack when carrying. Do not hit HDD each other. Installation (1) Please use the driver of the screw strictly....
Manual/User Guide
Page 9
SATA interface PCA and power connectors Figure 3.7 Connector locations C141-E245 3-9 3.3 Connections with Host System 3.3 Connections with Host System 3.3.1 Device connector The disk drive has the SATA interface connectors listed below for connecting external devices. Figure 3.7 shows the locations of these connectors and terminals.
SATA interface PCA and power connectors Figure 3.7 Connector locations C141-E245 3-9 3.3 Connections with Host System 3.3 Connections with Host System 3.3.1 Device connector The disk drive has the SATA interface connectors listed below for connecting external devices. Figure 3.7 shows the locations of these connectors and terminals.
Manual/User Guide
Page 10
... and select it from the PCA side Figure 3.8 Power supply pins (CN1) 3.3.3 Connector specifications for host system Table 3.2 lists the recommended specifications for the host system indicate only that its equivalents (compatibles). 3-10 C141-E245 Accordingly, the number connecter insertion/extractions including hot plugging is confirmed. Installation Conditions 3.3.2 Signal segment and power supply segment Figure 3.8 shows each segment of the connection with the SATA interface connecter is...
... and select it from the PCA side Figure 3.8 Power supply pins (CN1) 3.3.3 Connector specifications for host system Table 3.2 lists the recommended specifications for the host system indicate only that its equivalents (compatibles). 3-10 C141-E245 Accordingly, the number connecter insertion/extractions including hot plugging is confirmed. Installation Conditions 3.3.2 Signal segment and power supply segment Figure 3.8 shows each segment of the connection with the SATA interface connecter is...
Manual/User Guide
Page 11
3.3 Connections with Host System 3.3.4 SATA interface cable connection The cable that connects the disk drive to the host system must be compliant with the Serial ATA 1.0a specification. 3.3.5 Note about SATA interface cable connection Take note of the following precaution about plugging a SATA interface cable into the SATA interface connector of the disk drive and plugging the connector into a host receptacle: When plugging together the disk drive SATA interface connector and the host receptacle or SATA interface cable connector, do not apply more than 10...
3.3 Connections with Host System 3.3.4 SATA interface cable connection The cable that connects the disk drive to the host system must be compliant with the Serial ATA 1.0a specification. 3.3.5 Note about SATA interface cable connection Take note of the following precaution about plugging a SATA interface cable into the SATA interface connector of the disk drive and plugging the connector into a host receptacle: When plugging together the disk drive SATA interface connector and the host receptacle or SATA interface cable connector, do not apply more than 10...