Manual/User Guide
Page 3
When attaching the HDD to the system frame, do not allow the system frame to touch parts (cover and base) other than parts to Signal Ground (SG). C141-E245 3-3 ... in any direction. (2) Frame The MR head bias of the HDD disk enclosure (DE) is attached. The mounting frame is connected to which the HDD is zero. 3.2 Mounting 3.2 Mounting For information on mounting, see the "FUJITSU 2.5-INCH HDD INTEGRATION GUIDANCE (C141-E144)." (1) Orientation The disk drives can be 0.49N•m (5kgf•cm). The tightening...
When attaching the HDD to the system frame, do not allow the system frame to touch parts (cover and base) other than parts to Signal Ground (SG). C141-E245 3-3 ... in any direction. (2) Frame The MR head bias of the HDD disk enclosure (DE) is attached. The mounting frame is connected to which the HDD is zero. 3.2 Mounting 3.2 Mounting For information on mounting, see the "FUJITSU 2.5-INCH HDD INTEGRATION GUIDANCE (C141-E144)." (1) Orientation The disk drives can be 0.49N•m (5kgf•cm). The tightening...
Manual/User Guide
Page 5
3.2 Mounting IMPORTANT Because of breather C141-E254 3-5 Figure 3.3 Location of breather hole mounted to the HDD, do not allow this to block. Locating of Figure 3.3, at least, do not allow its around φ 3 to close during mounting. For breather hole of breather hole is shown as Figure 3.3.
3.2 Mounting IMPORTANT Because of breather C141-E254 3-5 Figure 3.3 Location of breather hole mounted to the HDD, do not allow this to block. Locating of Figure 3.3, at least, do not allow its around φ 3 to close during mounting. For breather hole of breather hole is shown as Figure 3.3.
Manual/User Guide
Page 7
Do not touch the printed circuit board, but hold it too hard, the cover and the spindle motor contact, which may cause damage to the disk drive. Pressing it by external magnetic fields. Static: When handling the device, disconnect the body ground (500 kΩ or greater)....3.2 Mounting (5) Service area Figure 3.5 shows how the drive must be accessed (service areas) during and after installation. Ensure that the disk drive is not affected by the edges. (6) Handling cautions Please keep the following cautions, and handle the HDD under the safety environment. C141-E245 3-7 Damage: Do ...
Do not touch the printed circuit board, but hold it too hard, the cover and the spindle motor contact, which may cause damage to the disk drive. Pressing it by external magnetic fields. Static: When handling the device, disconnect the body ground (500 kΩ or greater)....3.2 Mounting (5) Service area Figure 3.5 shows how the drive must be accessed (service areas) during and after installation. Ensure that the disk drive is not affected by the edges. (6) Handling cautions Please keep the following cautions, and handle the HDD under the safety environment. C141-E245 3-7 Damage: Do ...
Manual/User Guide
Page 8
... driver. Do not drop. Figure 3.6 Handling cautions - General notes Wrist strap Use the Wrist strap. M3 0.49N • m (5 kgf • cm). - Do not hit HDD each other. HDD is occasionally damaged by the impact of the driver. (2) Please observe the tightening torque of a low impact when you use the driver of the... 3-8 C141-E245 ESD mat Shock absorbing mat Place the shock absorbing mat on the operation table, and place ESD mat on it. Do not place HDD vertically to avoid falling down.
... driver. Do not drop. Figure 3.6 Handling cautions - General notes Wrist strap Use the Wrist strap. M3 0.49N • m (5 kgf • cm). - Do not hit HDD each other. HDD is occasionally damaged by the impact of the driver. (2) Please observe the tightening torque of a low impact when you use the driver of the... 3-8 C141-E245 ESD mat Shock absorbing mat Place the shock absorbing mat on the operation table, and place ESD mat on it. Do not place HDD vertically to avoid falling down.