Manual/User Guide
Page 3
... the screw length should satisfy the specification in any direction. (2) Frame The MR head bias of the HDD disk enclosure (DE) is zero. C141-E245 3-3 When attaching the HDD to the system frame, do not allow the system frame to touch parts (cover and base) other... than parts to which the HDD is connected to Signal Ground (SG). The tightening torque must be mounted in Figure 3.2. 3.2 Mounting 3.2 Mounting For information on mounting, see the "FUJITSU 2.5-INCH HDD INTEGRATION GUIDANCE (C141-E144)." (1) Orientation The disk drives can be 0.49N•m (5kgf•cm)....
... the screw length should satisfy the specification in any direction. (2) Frame The MR head bias of the HDD disk enclosure (DE) is zero. C141-E245 3-3 When attaching the HDD to the system frame, do not allow the system frame to touch parts (cover and base) other... than parts to which the HDD is connected to Signal Ground (SG). The tightening torque must be mounted in Figure 3.2. 3.2 Mounting 3.2 Mounting For information on mounting, see the "FUJITSU 2.5-INCH HDD INTEGRATION GUIDANCE (C141-E144)." (1) Orientation The disk drives can be 0.49N•m (5kgf•cm)....
Manual/User Guide
Page 5
Figure 3.3 Location of Figure 3.3, at least, do not allow its around φ 3 to close during mounting. For breather hole of breather C141-E254 3-5 3.2 Mounting IMPORTANT Because of breather hole is shown as Figure 3.3. Locating of breather hole mounted to the HDD, do not allow this to block.
Figure 3.3 Location of Figure 3.3, at least, do not allow its around φ 3 to close during mounting. For breather hole of breather C141-E254 3-5 3.2 Mounting IMPORTANT Because of breather hole is shown as Figure 3.3. Locating of breather hole mounted to the HDD, do not allow this to block.
Manual/User Guide
Page 7
...fields. C141-E245 3-7 Do not touch the printed circuit board, but hold it too hard, the cover and the spindle motor contact, which may cause damage to the disk drive. Ensure that the disk drive is not affected by the edges. (6) Handling cautions Please keep the following cautions, ...and handle the HDD under the safety environment. Mounting screw hole Cable connection Mounting screw hole Figure...
...fields. C141-E245 3-7 Do not touch the printed circuit board, but hold it too hard, the cover and the spindle motor contact, which may cause damage to the disk drive. Ensure that the disk drive is not affected by the edges. (6) Handling cautions Please keep the following cautions, ...and handle the HDD under the safety environment. Mounting screw hole Cable connection Mounting screw hole Figure...
Manual/User Guide
Page 8
Do not place HDD vertically to avoid falling down. HDD is occasionally damaged by the impact of the driver. (2) Please observe the tightening torque of a low impact when you use an electric driver. Recommended equipments ... Maker SUMITOMO 3M Achilles HIOS 3-8 C141-E245 Installation (1) Please use the driver of the screw strictly. M3 0.49N • m (5 kgf • cm). - Do not hit HDD each other. Do not stack when carrying. Figure 3.6 Handling cautions - Do not drop. ESD mat Shock absorbing mat Place the shock absorbing mat on the...
Do not place HDD vertically to avoid falling down. HDD is occasionally damaged by the impact of the driver. (2) Please observe the tightening torque of a low impact when you use an electric driver. Recommended equipments ... Maker SUMITOMO 3M Achilles HIOS 3-8 C141-E245 Installation (1) Please use the driver of the screw strictly. M3 0.49N • m (5 kgf • cm). - Do not hit HDD each other. Do not stack when carrying. Figure 3.6 Handling cautions - Do not drop. ESD mat Shock absorbing mat Place the shock absorbing mat on the...